Husqvarna 455 Chainsaw Not Oiling...Fixed!
ฝัง
- เผยแพร่เมื่อ 4 ส.ค. 2023
- Customer complaint is that the saw is not oiling. We confirm that and I show you how I repaired it. Along the way we discover clutch problems and I show you how to replace the clutch. #smallenginerepair
- ยานยนต์และพาหนะ
![เจอประจำ ตอน พักเที่ยง [EP.32]](http://i.ytimg.com/vi/jvqk6uJoVks/mqdefault.jpg)
Thank you Scott for your spot on instruction for this fix, you made it super easy for me to do this repair. I watched this vid two times and went to the shop and tore into it and now the old 455 Rancher is oiling just like she used to. You sir saved me a bunch of time and money, I appreciate it. Thanks again.😎👍🏻
You're welcome and thanks for watching!
Thanks for showing this! Followed what you did and this fixed the oil problem on my Husqy!
@@chrishorton6605 good job on that repair!
Thanks for the helpful info. I really appreciate your 'talking bubble' as you're a spectator with us and the instructor at the same time. 👍😊
I started doing that because I can't narrate a repair while in a shop at work. It seems to work this way. Thanks for watching!
Yes that clutch was done! Good job!
Ya you could tell it was slipping and heating up.
Quickest video straight to the point which is what most people need when coming to you tube. Thanks for your time. Going out to check now. Liked and subscribed!
Thanks for watching!
She’s Oiling Now 😀 Nice Find 😊👍🏼It Amazes Me How Micro Pieces of Saw Dust Get Past The Oil Tank Filter and Make There Way Between The Pump and Line or In The Bottom of The Pump Itself
Ya, I expected to at least find some junk in the tank but nothing.
I learn from each video. Thanks!!
@@alans.4658 You're welcome and thanks for watching!
Nice work on the 455 oiler. That impact is a big timesaver to removing the clutch it beats using the rope in the cylinder
It really is. Some people have claimed that they've sheared the flywheel key doing it this way so beware. I've never had a problem using it.
@@TheGreasyShopRag i actually have never done it but I must improve on my skills and technique….righty Lucy
Not to change the subject but I watched your video on your tool box that thing is a beast, it's on my bucket list. Great box thanks for the video.
I'm overdue for an update video on that box. Thanks for watching!
@@TheGreasyShopRag I watched a video today of a guy who said he learned about that new spark plug tester you used on your channel. Could you possibly show that again please in an upcoming video. That was a very impressive tool. Thank you.
@@drmikeyb1 I have over 200 repairs on file waiting to be edited. I'm sure some of them show that tool in use. Stay tuned!
@@TheGreasyShopRag awsome, thank you. I'm a disabled vet 57 years young working on chainsaws and weedeaters for a local company. I've learned a ton from your channel and I wanted to thank you for sharing. I could spend hours on a call with you on just questions regarding tools, repairs etc.. thank you again.
My chainsaw hasnt been on for at least 5 years; the oil pump was stuck and its teeth eaten up. 12eur later for a new pump fixed it and is now good as new.
Good job on that repair!
Good video keep them coming!!!
Thanks for watching!
Great Video!
Thanks for watching!
So what gets in there and clogs it, saw dust? Nice job on the fix
Whatever debris is clinging around the fill cap. A paint brush might be a good thing to carry in your saw case. Debris could be wiped away before the cap is removed.
Thanks man .
I like this saw over some other new saws, but they are still a pain in the ass to take apart, and its just ridiculous that such a small amount of sawdust can clog the entire system. I've used the 455 for 4 years and its powerful, works fine, but my Sachs Dolmar 111 is over 30 years old and has never had a problem with the oiler, even if it did I wouldn't have to take the clutch off to replace it.
Shows you how things have changed, that being said, I've had the pullcord system on most of my vintage saws fail multiple times, mostly due to bad design. The Husky and all my new saws have never had pull cord problems which saves me a lot of time on repairs
Yep, sometimes things improve and other times we long for the good ole days.
People are lucky your honest. Is it bad design or people? Recommend low pressure for the tank? Great job. Take care.
I was surprised to find a clean tank and now I'm wondering if the owner cleaned it in an effort to fix the problem? My air hose is regulated way down below tank pressure but its still higher than what I should have been pusing in that oil tank. I should have made some statement about "do as I say, not as I do" but in the end it all worked out.
@@TheGreasyShopRag shoot I’ve seen TH-camr’s using shop vacs. You can’t remember to say everything. We need to research too.
My k770 cutoff saw starts but once i turn it off it takes forever to start again, and it makes pops like theres pressure buildup and it just wont start it will keep making pops out of the exhaust
Have you crossed anything off the list yet? How is the compression and is the cylinder scored?
@@TheGreasyShopRag idk brotha, i bought it and blew out the filter and cleaned up the top, havent gotten deeper into it, when it runs, it runs like a champ. Just has a hard time turning back on quickly. My mazda rx8 had the same problem but i dont think its similar, idk why it would start and run perfect then not wanna start after, to me the cylinder should be fine bc it runs perfectly when it does run, wierd. Should i go to a small engine mechanic? Or what should i try first bro? Maybe carburetor?
@@graysonquenelle Certainly there are many possibilities why it won't restart but on a concrete saw I always suspect low compression. They have so much potential to suck in dirt and wear out that I always check that first.
@@TheGreasyShopRag It sounds like the connecting rod bearings are finished. You might as well tear it down and replace the parts or get a new saw, I had a similar problem with a weed wacker that was easily fixed with some spare parts I had lying around
Same issue with a brand new Poulan 4218 I bought in 2020, it ran for a couple of months then it would consistently turn off after 5mins of use, there isn't even anything wrong with the piston, its just very cheap and temperamental. Sometimes the saw is poorly designed or may have a defect so it ends up having a lot of issues that aren't worth dealing with.
I realized this when I bought a vintage 70s Homelite XL with a completely scored piston, the surprising part, it runs 10 times better than my 2020 Poulan does. Those Homelite saws are practically indestructible, I have an XL2 from the same era that runs even better, again, with a scored piston.
I have at least 5 box store saws from the early 2000s with no scoring on the pistons, I tore them down and cleaned them, but for some reason they wont start or refuse to stay running. Probably have worn out bearings as well but they are not worth fixing
Nice video, next time slam the tools harder!!!
Thanks for watching!
Cool
Thank you master
Thanks for watching!