That sensor is the crankshaft position sensor. If you are using the engine in an older car just remove the sensor and run OBD1 ECU and distributor. I’ve done it many times. Nice build.
hey bro, so pull the entire position sensor and then install a OBD1 ECU and Distributor? I'm sticking a h22A4 from a 97 into a 94 and i think i am running into an issue with this.
When installing the cams, make sure the key is pointing upwards. Once the cam gears are installed there will be an arrow on each one pointing up. There will be 2 timing marks on each cam gear. You want to line these up with the top of the head and make sure the gears are lined up with each other. It can be difficult to keep them in place because there will be some tension on the cam lobes. They do make a tool that holds the gears in place while installing the timing belt, but I was able to make it work without the tool.
Hello underneath the center cam cap is there just an o ring that goes in that circle groove or is there an actual oil restricter piston that is removable?
Hi I have a 4th gen 1995 prelude 2.2 vtec the h22a4 I believe, are the timing belt kits the same between 4th, 5th gen and accord type r's? As I'm struggling to find a timing belt kit for the 4th gen. Needs cambelt, tensioner balancing belt and water pump? Thanks
It can be a bit tricky to keep everything lined up. If everything is lined up right, it should slip on fairly easy. My belt was a bit tight from being so cold out, so ended up having to lightly pry on it with a plastic trim tool. Not the ideal way to do it, but it worked. Hope it works out for you buddy 🤙🏻
That sensor is the crankshaft position sensor. If you are using the engine in an older car just remove the sensor and run OBD1 ECU and distributor. I’ve done it many times. Nice build.
hey bro, so pull the entire position sensor and then install a OBD1 ECU and Distributor? I'm sticking a h22A4 from a 97 into a 94 and i think i am running into an issue with this.
Glad I ran into this video 🤌🏼im new to the h series stuff and this really did help me a lot appreciate you 🤙🏼
Glad I could help, thanks for watching🤙🏻
Same I was a D 😅
Mine had that sensor on the crank too, I just ran a 0bd1 dizzy and it works fine
That's cause In the older cars it is in the dizzy just take that out and run a obd1 dizzy and ecu
Question about the balance shaft belt, the rear balance shaft gear has a Dot on it, where is it suppose to be pointing?? 11 o clock position??
Hey Bud,I wanna ask about how to tight the timing belt? I so struggling to make it tight😅...Can U make the video for that?...
How did you make sure the cams were set at TDC?
When installing the cams, make sure the key is pointing upwards. Once the cam gears are installed there will be an arrow on each one pointing up. There will be 2 timing marks on each cam gear. You want to line these up with the top of the head and make sure the gears are lined up with each other. It can be difficult to keep them in place because there will be some tension on the cam lobes. They do make a tool that holds the gears in place while installing the timing belt, but I was able to make it work without the tool.
how did you get the motor to top dead center just lign all the marks up
Where the dowels easy to get out? what did you use? BTW Nice engine.
Awesome vid. Nice to see more h22 builders , have a instagram to follow?
Thanks buddy! Our ig is mtgarage_official. Haven’t been very active on there in a while. But will try to get on it again.
Dang that engine is looking niiice.
So scared to scratch it now 😅
Can someone help me with my timing belt for my 96 prelude Si. It snapped and I have no idea how to TDC the cams before installing a new timing belt.
my 98 bb8 h22a8 does not have a crank possition sensor
Hello underneath the center cam cap is there just an o ring that goes in that circle groove or is there an actual oil restricter piston that is removable?
The o ring goes on the orfice not above the orfice like he had installed.
Hi I have a 4th gen 1995 prelude 2.2 vtec the h22a4 I believe, are the timing belt kits the same between 4th, 5th gen and accord type r's? As I'm struggling to find a timing belt kit for the 4th gen. Needs cambelt, tensioner balancing belt and water pump? Thanks
96 in the bastard year... They put out obd1 an obd2
Love the vidoe
Awesom work man. 👌🏻👌🏻👌🏻👌🏻👌🏻
cool!
You sure do have some girly soft looking hands you touch that engine with the upt most soft touch anyone has ever seen lol gjgj
Yo how did u get the belt to slide on the last cam gear it cut off…. Im struggling lol
It can be a bit tricky to keep everything lined up. If everything is lined up right, it should slip on fairly easy. My belt was a bit tight from being so cold out, so ended up having to lightly pry on it with a plastic trim tool. Not the ideal way to do it, but it worked. Hope it works out for you buddy 🤙🏻
Nice 👍.
What ecu and trans are you using
Currently running a chipped P28 by clubbed inc for the NA setup. will be running a Hondata S300 for the new engine with boost.
instructions unclear, my wiener is now stuck in the engine
jokes aside great vid