Treadmill not working?
ฝัง
- เผยแพร่เมื่อ 12 พ.ค. 2020
- Joe the Treadmill Hero walks you through questions to ask yourself if your treadmill isn't working. He'll also show you what to look for and test on the machine itself. Maybe you can fix it yourself!
Hello and thank you for tuning into another Treadmill Heroes video!
If you need further assistance, please call our technicians at our sister company, The Fitness Graveyard. Their number is 563-949-0799. If you are looking for parts for your machine, please visit fitnessgraveyard.com.
If you are living in the US and are looking for new and used fitness equipment, please visit our website treadhero.com.
Thank you! 😄
great video ,you are helping a lot of people , but not me😞 because i have maybe another probleme ,i was raining for 35 minutes by the rate of 5.5 km/h and it start beaping ,a long beep that wont stop ,i got scared and i turned it off know whenever i start it ,it strat beeping and still turning at the lowest rate 0.8 km/h ,so i hope you answer to the this and help me plz
ps : i am from algeria north africa so i can't just come to your place or contact your number
One of the clearest, most helpful videos I've used on TH-cam. You are a natural educator.
Thanks legend.
I had the 2nd case: not used treadmill for some time and also shifted from one room to another so per your guidance I unplugged the Data cable and replugged it again and it starts working. WOW. So simple, yet technical. You Saved my time and money. Hats off to you.
This was a great find. Although it did not help me directly with my problem, I found you and I am grateful. I have already reached out to your team to narrow down my issue. Thank you very much in taking the time to do this.
What's the solution then.??
Someone left there treadmill at my new house and I just want to thank you because I just needed to know where the power switch was to see if it worked and it does. So thank you!
Very good video, very informative, especially the ways to check the motor status. I don't need to repair my treadmill now, however it's always good to get prepared. Thanks a lot!
This clip helped me isolate the problem, that it wasn't the motor or the belt and maybe the control board. Another video about the blinking light on that board may assist in your diagnosis. That showed my board to be working too. When I pull off the black and red wires from the board and checked the motor with my drill battery, as Joe suggested here, the motor ran perfectly. When I reconnected the wires the whole Nordictract c850 s ran perfectly. Poor contact to the motor due to mild corrosion. Problem solved until next time. Thanks Joe.
Couldn’t figure out why my treadmill wasn’t working. I had given up - not very mechanically inclined. However, as a last resort I thought I’d check TH-cam.
As soon as you mentioned recently moving your treadmill, it clicked. I found the Ethernet cable and realized I had bent one of the pins when I reconnected. A few adjustments with needle nose pliers, and I’m back in business. Thanks!
Thanks for the great instructional video. This treadmill had just been moved. I checked the data cable and found that when I plugged it back together (multi pin connector), 2 of the pins were pushed part way out. I pushed them back in and the belt belt is turning. Thanks again.
Thank you very much Jo, can’t thank you enough, it’s was your very last closing remark- Power AND , the Safety Catch- The latter saved my Treadmill from being scrapped, God bless you.
This is such a great comment to read!! Thank you.
This is great. My safety key was *only partly* plugged in. It wasn't obvious at first. All I had to do was plug it back in all the way and voilà, its working. Thanks!
thank you joe, the feed wasn't getting through to the top screen, took it apart and the wire had snap completely in half. was difficult to reconnect as wires were so tiny but with care n patients manage to strip them back enough to twist each colour together then using plenty black insulating tape to separate and make safe.... also wound some the tape around the rest the lead to hopefully strengthen it from future damage etc.
I couldn't believe how dusty it was especially where the motor sits etc. all cleaned up and ha presto it's working again, many thanks joe for your video and help, son n wife happy again.
Man this was so helpful! It was my stop cord the whole time! Was about to hire someone for this lol... Thank you!!!
Very good video -- very well explained -- My old WESLO has not been used for a year or more, and not moved. When attempt to use it would not work. Too late now but tomorrow I will thanks to all your guidance check it out. If only many other repair videos were explained in the same direct manner of instructions and video. Thanks for taking the time and effort for making this video - even if my treadmill IS completely dead.
If you need any help diagnosing issues along the way, you can always give our company, Fitness Graveyard, a call at 563-949-0799. We have in house technicians that you can speak with. Thanks!
@@treadheroes you're the man! Thanks so much for a great video!!!
Thanks for this video. You just saved me 400$ in parts/labor due to my part still being under warranty. This was a huge help. Appreciate it.
Great to hear!
Thanks for the video! My belt wasnt working but everything else did. It turned on and it inclined/declined just fine, but the belt didnt work. I checked the motor per your instruction by connecting it to a drill battery and the belt worked perfectly. I was thinking its was the data cable because the motherboard looks fine with no corrosion. After a thorough inspection of the data cord is found the the "spokes" on the male data cord was bent and not aligned so it wasnt plugging with the female part correctly. After straighting it out, it works! Thanks so much!!!!!
Thanks for your time and effort in providing such a nice video, it really was helpful.
I just talked to Drew at The Fitness Graveyard - VERY helpful in helping me narrow down my issue. Hopefully, I can 'adjust' my problem out, but if not, he told me exactly what is most likely my problem part and how to deal with it. I appreciate it - I'll report back when I figure it out.
By far, the MOST HELPFUL video! Thank you!
Another repair down in the books. Thank you. I had a bad power wire to the panel, then found out one of the magnets in the motor came loose. Welp I cleaned and epoxied it back in. Now I got a $500 treadmill for $1.53 from the thrift store.
Time to start running. 😁
Just had our home treadmill die and was flying blind testing stuff, this is an awesome video and gives me a place to start from
Great vid! This totally helped me resolve my issues in just a few minutes:)
💯 thanks!! I learned how to test my drive motor. 18V cordless drill battery 🔋 worked! Control board is being fixed; wanted to confirm motor was good. 👍
Decent video. Explains a lot. Thank you for sharing 👍😁
great!!! love your expertise... stay blessed my beloved brother
This seems like a great video to help the average person try and trouble shoot. Well done.
I will echo the comments by @EricaChiarkas that you are a natural educator. So many presenters on TH-cam rush through their dialog, but you took your time like talking to a friend or neighbor across the way. I was able to solve a power issue with my old Triumph T400. Just taking the top cover off allowed me to see that the white power lead had disconnected from the circuit board. I had replaced the power cord a while back and didn't leave enough slack on the wires inside, so of course when I folded up the platform one day after use, the wire was pulled off. Thank you Treadmill Hero!
Thanks for the nice comment
thank you so much . I have an old Image 10 that is 22 years and has been moved a few times but still working fine. I hadn't used it in a couple months though and when I went to start it it wouldn't start. Nothing. After watching your post when you mentioned that the key has to be in thats when I remembered. The key. Oh yeah. It would be good to mention the reset button early on too. I had tried that.
You explain it in a great way fully..! Thank you..!
Glad I found this video - we were given a Trojan 210 treadmill, the treadmill powers on - counts down and we get a L51 error. Checked the motor with a 12v battery and the motor is good. As mentioned before the console counts down, a 3rd light glows up - no click, error and the 3rd light dims again :(
Will find out why by hook or by crook :)
Great video! Thanks so much for making this!!!
AWESOME VIDEO!!!! Thanks for the tips. 🇺🇸🤙🏽
Good information,,,, thanks for taking the time,,,Ready to jump on it with this new knowledge ...lol
Great video. Very helpful. The mice got in to our treadmill and chewed the powercord, which I soldered back together. They had also nested on the pcb. Now the console powers up but the motor won’t turn. The mat is hard to turn which thanks to your explanation about the motor becoming a magnet tells me the motor is good but is shorted somewhere. Thanks for the video!
This is what happened to mine…did you ever resolve the problem?
@@picsbyandrea No sorry i didn't. The frame got converted into a table for my screen printing press and the rest got thrown out (apart from the motor which may get used for a future project)
Thank you for the tips. Extremely helpful!
Glad it was helpful!
Excellent presentation.
Great vid! Super helpful!
Thank you🙏
Wow Excellent excellent explanation thank you for all the help 😊👍👍
Thanks for this video! Wealth of knowledge 👍🏻
brilliant info w/the battery check!
Great tips on troubleshooting, appreciate it.
I really like the part where you teach us on how to test the treadmill motor if it is still good it really helped me a lot thank you.
It is working now thanks It makes anything possible when a HERO has your back! A team plays harder when there is a heroic quarterback behind them.
Excellent technical experience and information. Thanks
Thanks for the positive vibes
Wanted to thank you for your trouble shooting video. It was a move resulting in a disconnected data cable. If I am in need of any parts you will be the busy I call. I will refer your company to anyone I know who is having treadmill issues. Thank you again.
thank you it was really helpful.
My treadmill(PRO-FORM 590QS Quiet Deck) starts and works as long as I am only walking but once I get to running speeds then it stops after a few seconds to a minute. What should I look for?
I’ll definitely run the diagnostic that you have explained here.
Another thing, for past few years the tread has become quite loud. It hasn’t bother me since it’s been moved from bedroom to the garage and I usually have my AirPods on but it used to be very quiet for the longest time. Don’t know if it’s aged or some parts can use some lubricants to make it quiet again?
Btw, very well explained and easy understand video👍, thank you for sharing 🙏
Question
Proform Crosswalk 380
I press start and it goes for about 1 second and turns off. It was working until one time I pulled the safety key by accident right after starting the walk workout. Have not recently moved the machine. control panel works. One thing there's a small black wire not connected to anything. This wire is right along side the main power cable that goes to the wall. What should I do?
Thank you so much for this video!
Having motor issue on PaceMaster as shown in video. Motor has power but not enough to move belt consistently with person walking/running. Will start out working fine then slowly come to a stop. Suggestions for what to troubleshoot?
Thanks very helpfull I will check both
Just wondering if you have a closer view of the item you called the spine of the treadmill? Mine stopped working after it was moved.
Thanks a lot for your explaination
Hello Joe, I was about to give up trying to fix the incline setting which was stuck in number 10 nobody wanted to used it . Then You mention cables loose due to moving the unit from one area to another. To pleasant surprise I found a cable disconnected plug 🔌 it in and problem resolved. Thank you very much great video.
Great troubleshooting
Great info! Thanks!!
Great video! Thank you!
NOTE: This product works exactly as described. th-cam.com/users/postUgkxguEIMc_Qwab-3QMTpF6jaRL80hiOOsIN It originally earned a four-star review due to a minor defect (see below). However, the manufacturer's customer service rep (Lita) went above and beyond the call of duty and deserves five stars now. I wish I could give even more!I purchased this item which arrived quickly. Assembly instructions were easy to follow. There was only one problem: One bolt did not screw into the hole properly. I called the company. Their customer service rep (Lita) was terrific! She took all my information and submitted a request to replace the defective part. I'm hoping to finish assembly and start using this treadmill soon. (Fingers crossed...)FOLLOW UP: Lita called back to inform me that the company will send a replacement part AND a technician(!!) to install it properly. AMAZING CUSTOMER SERVICE!! Thank you!!
Hey I have a question about a NordicTrack treadmill I have. A few weeks ago, the power switch began to shut off on its own at high speed like 11mph. Now it’s happening on lower speeds. The deck is oiled, and I tried a new control board so I’m not sure what could be wrong
"The data cable is the spinal cord of the treadmill" - great description.
Would body weight have anything to do with it stopping after a couple of minutes?
Hi what does it mean E1
Very helpful. Thank you.
Glad it was helpful!
Hello, my proform 330i treadmill turns on without inserting the key and the stop button does not react and it does not turn off when I remove the key, what do you recommend?
Mr. Joe, I need your helpful advice, please.
I have ct9.3 horizon folding treadmill. It suddenly stops and there starts coming clicking sound from the motor control board. After a long time it resets itself automatically and again stops and same clicking sound starts coming from the control board.
Can you please advise what trouble this can be and how to fix it.
Thanks.
Any way to feed the upper console 12v to confirm it still powers on with the battery? To possibly further point to it being a cable or lower control board issue…
I heard a pop then smoke when I plugged it in , haven’t used it in a while . What do u think it could be ?
I have a Bowflex BXT216 and today after my workout as I was finishing up my workout, started slowing it down by pushing on the speed decrease button. That was it. The button never stopped klicking. Stop button doesn’t do anything. The start button is working, but speed increase/decrease doesn’t do anything. But the Kees keep clicking on their own. I’ve unplugged it then plugged back in still the clicking sound doesn’t stop.
Error message says key button stuck.
Any advice? Thanks
My treadmill stops when I step on it and throws a E2 code. Xterra trx3500. Any idea of what the problem is? as long as I'm not on it it runs fine at all speeds and all incline levels. Only when weight is applied is when it stops
Your the man. I fixed my treadmill. I though it was the drive motor.
Hey joe I have a question for you.
Do the Circuit boards have to be exactly the same I cannot find the circuit board for my treadmill so I’m wondering will I be able to use any kind of circuitboard for the treadmill? If you could please get back to me would be greatly appreciated.
Thank you so much for this video
Motor is fine I tested with battery and it’s work but when it’s plugged belt doesn’t run error 94 comes up
Can you recommend a site which gives the reset sequence to reset my reebok zR8?
I have a Temp Evolve treadmill, and while the motor still works, I have to put my foot on the belt and move it backwards to get it going. I wonder if lubricating the belt will fix this problem?, Or is there some other solution?
We went thru the whole procedure of removing the cover and testing everything. Come to find out it was the on/off switch on the case next to were the power line goes in was switched to off. I don't know how it could of been switched off during our walking.
Hi what can you do when no power on the console at all and the light is there on the mother board check the harnes and nothing check the motor and is working any tips
Excellent vid
You are the main dude DIY for the win thanks to youtube and doers. Just fixed it
I have a bh fitness model t8 pro it’s showing a E1 code any ideas
Any thoughts for belt stops suddenly then restarts on its own? Landice L7
Nice explanation
Hi. Would you know the white wire which comes from the mother board is Neutral or Live wire please?
It was like you were directly talking to me with my issue. How do you replace the relay switch?
mine got wet with rain and doesn't do anything, can it still be fixed?
Hi, just curious if you can help me. My treadmill A Proform is 5 years old.
Recently during excercise the belt stops. Motor is running and if I step off the deck she starts running again. If I step back on deck she stops. I have lubricated with sicone spray, nothing is overheating so I think o5 may be a tension thing. Any he,p would be great. Neil
Great video, my treadmill shows E6 and is a maxed brand. Any idea what could be the probs?
Great video. Thank you!
So I don't hear the "click" when I try to start it up. Do you have a video on how to replace a relay?
My motor powers on with a 9v battery and the relay clicks over but the motor still won't turn over. Bad board or relay?
Can u help me mines worked before i moved it now it doesn't. I plugged it up it powers up incline works but wont move i did the battery thing n it moved.
Thank you for taking the time to produce your excellent videos on maintaining a treadmill.
I need your assistance. I have a Sole F80 and while I’m running (7MPH) or walking (4MPH) every now and then the treadmill will stop then speed up rapidly (Fast) and it will give me an Error Code 5 message on the screen. I’ve been thrown off the treadmill twice and I’m lucky it hasn’t caused me a serious injury. Do you have any idea what could be causing this happen?
Thank you.
Hi,
I have a Treadmill CT81, I verify the motor with a 9 volts battery and the motor is working fine.
Now having the motor controller on hand p/n JC22-001 or 032671-HF replacement no.
My question is what could I check with a multimeter if this controller is good?
Nothing seem to have heated up, everything look fine visually!
Thank in advance if you could help!
Pierre
Thanks for explain.
Is there a video on testing relays or replacing them
Hi Joe we moved our treadmill worked fine before we moved it. It turns on but nothing else happens, The Data plug is in so that not the issue. Any help would be great
Hello Joe, so my problem it starting out smoking kinda like a electrical smell so my son shut it off now my Son it's been maxing out at 10 so he has been putting a lot of work on the treadmill, I went on it to try it out and for a bit it was good then the smoke started coming back then immediately I heard and saw a couple of flashes then I turned the machine off I just seen this video and I tested the motor with the battery and it did go the clips where getting red hot but in the mean time the motor was going, any input that you might think could be? Thank you...
thanks for the vide and suggestions, trick testing motor saved me $300 mine working just fine tried w my drill battery
Hey guys I have a Horizon CST3.6 everything lights up on the dash but treadmill won’t start I did try the test for the motor with the battery and everything works as far as it goes. I can hear the clip but I don’t know what else to test
Any idea why my whole thing would just stop working? Turned it on, screen turned out, hit end button and then it just completely shut off, does not turn on now, does not do anything at all. I csnt figure it out. Console does nothing now. 😢
Hey what should you look for when the screen works fine but the buttons don’t - press the buttons and nothing works? Cheers
Hey bud, any fix suggestions for treadmill going slow then fast continuously?
Good tips! Used drill battery to test, motor works. Trying to figure out what E6 code is on xterra 2500 means right now.
Great vid. Great conent