I got that same model. It was runny at first but used your tip to change the orafice and helped it a lot. I had to play around with the dilution ratio, putting more soap than water probably about 4 oz, the rest water. I also bumped up the + button to add more foam (It’s thicker but still a bit runny) . And yes it does use a lot of product. I would say, it’s gone doing one round for a whole car. I’ll upgrade later in the future but for now, I’m pretty content with it. Thank you for your videos!
Thanks for the review. I changed out the orifice and thought I was doing something wrong, but I'm glad its not just me and the foam cannon just doesn't produce enough foam.
I got the same results with the Trinova. As a new detailer, I thought I was doing something wrong and couldn't figure it out! Honestly glad to see this video and know it's not me!
Hey josh from Brooklyn NY! Love your content man I’ve learned a lot especially about changing the orifice but i think you should give the Trinova another shot. I got mines before watching your video about switching the orifice, and after doing so it made a dramatic difference for me. I think the reason your results were different is because of the soap/water ratio your using. Like you noted, it’s a much bigger foam cannon but I think you had too much water. I use 2oz of soap and about 16oz of water with a 1600psi 1.7 gpm AR blue clean electric pressure washer. I also think that fan spread was effected when you removed the black head piece because mines does spread wider. I could be bias but for me it honestly preforms well for the price. I will say though it is heavier to handle because of the Sz and it does suck up more solution.
I've got essentially the same foam cannon from Tool Daily, and like you, I changed the orifice to a 1.1, as my unit came with BOTH a 1.1 and a 1.25, and I am using an electric pressure washer. HOWEVER, if I might make a few small suggestions that might increase the consistency and accuracy or your reviews: : You spoke about adding a somewhat random amount of soap and then "sort of filling" the container. I think this would cause you to have inconsistent soap to water ratios from unit to unit. EVERY soap manufacturer I have seen or used recommends some specific soap to water RATIOS, I.E. 1:10, 1:15, etc. Also, I always use Reverse Osmosis or Distilled water to mix with the soap concentrate, something else I picked up as a tip along the way that made sense. By mixing my soap 1:10 with RO water and using the 1.1 orifice, with a generic electric pressure washer with 1.6 rpm, I get REALLY great "shaving cream" foam. Just my thoughts as to a couple of things that could possibly provide more CONSISTENCY as you compare foam cannons. Give the consistent ratio idea a try and see if you don't get more relatable results. Obviously if you mix soap at different ratios, you will get different results, and without mixing to known ratios and just filling some soap and filling the different size containers, you are going to get different ratios. Something to think about and consider. I been a subscriber for some time, and really thoroughly appreciate your channel and the analyses that you do around pressure washing car gear.
@@gabepelletier3602 Gabe: when my Foam Cannon arrived, it had the 1.25 orifice installed, and I just immediately changed it to the 1.1. If in doubt, OR, if yours perhaps came WITH the 1.1 already installed, simply remove whatever orifice is installed, and compare the two, then choose the smaller orifice. FWIW, especially given Winter Weather, I really don't do a full pressure washer and foam cannon wash very often, and ONLY when the car is REALLY dirty, I.E. mud, etc. I've been experimenting with Yvan Lacroix's advice about using a Rinseless Wash to pre-spray the car even before a Foam Cannon wash, however doing a Rinseless Wash the MAJORITY of the time. Bottom line: it has been working BEAUTIFULLY, has drastically reduced my external cleaning/washing time and work, and in carefully examining the surface, I am NOT getting increased micro-scratching, it appears to be even LESS than when I was Foam Washing more frequently. In my case in particular, I am in my 70's, and have a VERY Bad Back, so this makes a significant difference in my ability to continue to do my Car Finish Detailing, something I have enjoyed for over 35 years. Have Fun!! I don't mind at all if you have any additional questions.
Ok so heres a real life review. I bought this foam cannon about 5 yrs ago. This was after owning the mtm hydro pf22 for 6 months..eventually the threads on my bottle were shot so I saw this for $35 on amazon. Now, at the time i was using a gas powered 2200 psi Briggs&Stratton. This was by far jus as good as the $100 mtm. Huge amounts of foam and it also has a larger reservoir with a wider mouth. You cant go wrong with this is $40 is all ur looking to spend. I personally give it 5 stars..great product.
I have the Trinovea foam cannon and it works well for me on an electric Pressurer washer. Just changed to a 1.1 MM orface today. Cant wait to try it out. Very nice foam before the change..Thanks for all your tips. Cris
It does unscrew but they are incredibly tight from the factory. I had to remove the top mix valve so I could grab the body in my vice then unscrew the front. There's nothing fancy in it, it's a standard stainless foam pill. I've ordered the denser / heavier pills from Aliexpress to test with. I've tried several things and while I'm much closer to the foam my MJJC will produce I haven't got there yet with this unit. The bottle will hold about 50oz filled to the top so it's easy to get a usable 48 in it but not 2L.
Hey Josh. I just got my 1600 psi Ryobi pressure washer today after watching your video. I also got the Sunjoe foam cannon and switched it to the 1.1 mm orfice.
Just reminding you on one of your soap challenge videos you mentioned doing a foam cannon maintenance video. Maybe you can possibly added it while doing another foam cannon review.
I have the Tool Daily which is very similar. I have to adjust to the - for more foam. Still doesn’t make much even after changing to a 1.1. I don’t know how there were so many 5 star reviews…
Same results. I honestly thought it would be more foam. Like you said..mesh might not be woven as tight as some of the others. Hopefully you can get to it and be able to change it and test it with other. Good luck 🤞
Not sure what’s wrong with yours but my Trinova makes super thick foam with my active pressure washer. The only soaps that I’ve used is Mr Pink, Honeydew, and Tough Mudder. All have made super thick foam.
Maybe because since it’s a bigger bottle, you should have started out with more soap. If it’s a 2 liter bottle you had more water in it then if you used a 1 liter bottle. I don’t believe it was the mesh that was the problem.
I have the trinova and agree the build quality is very good, certainly worth the money. However, I switched to 1.1 AND switched the mesh filter and still don’t get the super thick foam, not sure what the issue is but now am becoming curious to solve it somehow. As for your question on how to access the mesh filter, I put mine in a bench vise and backed it off with a big wrench. You can get to it, but it’s very tight, you have to back off one of those brass hex nuts once you take off the black plastic piece. You were on the right track.
My first cannon was the Amazon Tool Daily which is nearly identical to the Trinova. It works OK...consumes a lot of product, though. It came with a defective nozzle which didn't adjust much like yours, but they sent me a new one and was fine. I agree no way yours is a 2L...looks like 1.5L like the Tool Daily. Even at 1.5L it's pretty heavy on a stubby gun. Worth the $25 I paid...I'd say yes. My Griot's Brilliant Finish puts it to shame with foam quality, as expected.
Great reviews ! One more thing you may want to ad is a pin gage set to see what hole size actually is. Since most of box info is not accurate. So I would say the holes on tips are not what they say !
I have A Griot's and A Trinova...haven't used them yet. I'm using My MaxShine! I have one for foaming... one for foaming wheels with brake buster or Adam's wheel&tire cleaner.
I bought the Trinova and wasn't that impressed even after switching the orifice. I bought a Bravex foam cannon - it comes with the 1.1 orifice and seems to foam much better. I did start having better luck with the trinova by lowering the amount of water in the bottle. The larger bottle size seems to throw off the ratios.
Got the Bravex one off Amazon and really enjoying it. Don't have any anything to compare it to but it foams thick as I expect it to. Funny because the TriNova was also on my list, whew. Could just be a bad one.
I also just picked up a Bravex, very happy with the foam, using P&s Perl and the Ryobi 1900psi pressure washer. Much better than the tool daily cannon I used prior.
imjoshhv… To get to the foam filter you need to pull off the back larger oring carefully (pulling off the oring is necessary so your wrench fits flat and also so the oring doesn’t get damaged) and put one wrench on those machined flats - then put another wrench on the flats that you had the wrench on towards the front. Hold the back wrench in the tightening position and use the front wrench to loosen the front section. It’s going to take a some force because the units come torqued down pretty good. The filter is a standard mesh filter. Hope this helps!
I have this foam cannon. I changed my orifices out to a 1.1 using a ryobi 1.2 gpm, 2000 psi and i get crazy thick foam with chemicals guys water melon and meguiar's gold class soap
What do you mean by "twist the knob all the way to"? All the way to what? Are you saying it's backwards from other cannons and you turn the knob all the way to THE LEFT (counter clockwise, loosen) instead of the typical tightening it clockwise to the right?
@@haroldwhite7464 no, usually you are advised to close it by turning it in to the right which is negative (-). Negative is less water. You can see in the video that he turns it all the way to the right to close it. Are you saying he should have tuned to the left?
@@10SecondZ06 yep, he turned it the wrong way. I have the Trinova with the 1.1mm orifice, with Mr Pink and my foam is twice as thick compared to what you see in this video.
Josh, I have the TriNova which I bought last year and it works great with my gas powered pressure washer. After watching your review of the Greenworks 1700 psi 1.2 GPM electric pressure washer (from Lowes), I bought it and it works great… EXCEPT it will not produce good foam even after changing the orifice to the 1.1 and even using Adams MegaFoam. After watching your review of the Griott’s foam cannon, I bought it, installed the 1.1 orifice, but the Greenworks 1700 electric pressure washer will not produce any good foam with either foam cannon so I’m really bummed out about that.
Wondered if you do a video questioning the effectiveness of phone cannon's? I think it's cool, I like spraying the car fully with foam I have to keep going in a bucket except maybe a Rinse bucket once a while.Seems like it can be more efficient. Otherwise I don't think foaming a car actually does anything Is implied
I really think you need to be more consistent on your solution. Instead of using markings on the bottle since every bottle is so different, use an actual measurement and make it the same for all your reviews. Also try all the cannons on different settings. I think you should go through all your "bad" with these new rules and you will get differences
This is a rebranded one on Amazon called tool daily, same stuff, I changed to 1.1 orifice, holds like a quart of product but will go through it all quick
Thanks. I looked it up. It comes with a 1.1 orifice too. I was about ready to buy the trinova 1. But if it's the same, and it comes with the 1.1 to swap in period that I'll get that 1
@Srikanth Prabha More foam means that it sticks to the surface longer, so the soap can do its job better. More runny means that the soap is running right off pretty quickly.
I have this foam Cannon and I was expecting much thicker, richer foam after switching to a 1, but it stayed runny like in the video. I tried it with Adams strip wash, megafoam and a Maguires soap from Costco and it just didn't perform
Try changing the Foam maker to a more dense one, you can get to the phone maker by taking off the plastic sleeve in the front of the sprayer and unscrewing the tip and it will reveal the foam maker
You know how difficult it was for me to find out the answer to what orifice this came with?- very hard , no one had answers even the sellers. Thanks for answering the size
I've used a $40 foam cannon and a $9 one..after putting the 1.1 orifice in them, I can't tell any difference. That orifice is the only thing that matters unless your using a powerful gas washer that does over 2000psi. It's weird you saw no difference...you should maybe change the foam mesh piece that's on the other end of the housing.
@@VegasStacker702 I think 1.1 should still be fine because you want it to be small as to get more foam out of it. You could buy a 1.1 and a 1.2...on electric pressure washers there's a noticeable difference between 1.1 and 1.2
I'm pretty disappointed in mine. Got a new orfice after watching your other videos and it's still not great. Added more soap and it's still runny. Waste of money.
I got the exact same results that you did and returned the cannon immediately for the MJJC
I got that same model. It was runny at first but used your tip to change the orafice and helped it a lot. I had to play around with the dilution ratio, putting more soap than water probably about 4 oz, the rest water. I also bumped up the + button to add more foam (It’s thicker but still a bit runny) . And yes it does use a lot of product. I would say, it’s gone doing one round for a whole car. I’ll upgrade later in the future but for now, I’m pretty content with it. Thank you for your videos!
Thanks for the review. I changed out the orifice and thought I was doing something wrong, but I'm glad its not just me and the foam cannon just doesn't produce enough foam.
Mine came Chunked up as well but worked fine. However i did change mine over to a ridge washer 1.1 orifice and it is amazing. Foam comes out Thick.
I got the same results with the Trinova. As a new detailer, I thought I was doing something wrong and couldn't figure it out! Honestly glad to see this video and know it's not me!
Hey josh from Brooklyn NY! Love your content man I’ve learned a lot especially about changing the orifice but i think you should give the Trinova another shot. I got mines before watching your video about switching the orifice, and after doing so it made a dramatic difference for me.
I think the reason your results were different is because of the soap/water ratio your using. Like you noted, it’s a much bigger foam cannon but I think you had too much water. I use 2oz of soap and about 16oz of water with a 1600psi 1.7 gpm AR blue clean electric pressure washer.
I also think that fan spread was effected when you removed the black head piece because mines does spread wider. I could be bias but for me it honestly preforms well for the price.
I will say though it is heavier to handle because of the Sz and it does suck up more solution.
I got this foam cannon and I switched to the 1.1 orifice and it got me good thick foam
I've got essentially the same foam cannon from Tool Daily, and like you, I changed the orifice to a 1.1, as my unit came with BOTH a 1.1 and a 1.25, and I am using an electric pressure washer.
HOWEVER, if I might make a few small suggestions that might increase the consistency and accuracy or your reviews: :
You spoke about adding a somewhat random amount of soap and then "sort of filling" the container. I think this would cause you to have inconsistent soap to water ratios from unit to unit.
EVERY soap manufacturer I have seen or used recommends some specific soap to water RATIOS, I.E. 1:10, 1:15, etc.
Also, I always use Reverse Osmosis or Distilled water to mix with the soap concentrate, something else I picked up as a tip along the way that made sense.
By mixing my soap 1:10 with RO water and using the 1.1 orifice, with a generic electric pressure washer with 1.6 rpm, I get REALLY great "shaving cream" foam.
Just my thoughts as to a couple of things that could possibly provide more CONSISTENCY as you compare foam cannons.
Give the consistent ratio idea a try and see if you don't get more relatable results. Obviously if you mix soap at different ratios, you will get different results, and without mixing to known ratios and just filling some soap and filling the different size containers, you are going to get different ratios. Something to think about and consider.
I been a subscriber for some time, and really thoroughly appreciate your channel and the analyses that you do around pressure washing car gear.
Quick question, I also bought the tool daily foam cannon and don’t know if the 1.1 orifice was already installed or was it in the baggie.
@@gabepelletier3602 Gabe: when my Foam Cannon arrived, it had the 1.25 orifice installed, and I just immediately changed it to the 1.1. If in doubt, OR, if yours perhaps came WITH the 1.1 already installed, simply remove whatever orifice is installed, and compare the two, then choose the smaller orifice.
FWIW, especially given Winter Weather, I really don't do a full pressure washer and foam cannon wash very often, and ONLY when the car is REALLY dirty, I.E. mud, etc.
I've been experimenting with Yvan Lacroix's advice about using a Rinseless Wash to pre-spray the car even before a Foam Cannon wash, however doing a Rinseless Wash the MAJORITY of the time.
Bottom line: it has been working BEAUTIFULLY, has drastically reduced my external cleaning/washing time and work, and in carefully examining the surface, I am NOT getting increased micro-scratching, it appears to be even LESS than when I was Foam Washing more frequently.
In my case in particular, I am in my 70's, and have a VERY Bad Back, so this makes a significant difference in my ability to continue to do my Car Finish Detailing, something I have enjoyed for over 35 years.
Have Fun!!
I don't mind at all if you have any additional questions.
@@gabepelletier3602 Oh, sidebar, if I was to replace the cannon I have, I WOULD most likely get the MJJC.
Ok so heres a real life review. I bought this foam cannon about 5 yrs ago. This was after owning the mtm hydro pf22 for 6 months..eventually the threads on my bottle were shot so I saw this for $35 on amazon. Now, at the time i was using a gas powered 2200 psi Briggs&Stratton. This was by far jus as good as the $100 mtm. Huge amounts of foam and it also has a larger reservoir with a wider mouth. You cant go wrong with this is $40 is all ur looking to spend. I personally give it 5 stars..great product.
You think a 1800psi electric pw would produce less foam than a 2000+ psi gas pw? Meaning a gas pw with more psi creates thicker foam?
I have the Trinovea foam cannon and it works well for me on an electric Pressurer washer. Just changed to a 1.1 MM orface today. Cant wait to try it out. Very nice foam before the change..Thanks for all your tips. Cris
It does unscrew but they are incredibly tight from the factory. I had to remove the top mix valve so I could grab the body in my vice then unscrew the front. There's nothing fancy in it, it's a standard stainless foam pill. I've ordered the denser / heavier pills from Aliexpress to test with. I've tried several things and while I'm much closer to the foam my MJJC will produce I haven't got there yet with this unit. The bottle will hold about 50oz filled to the top so it's easy to get a usable 48 in it but not 2L.
Hey Josh. I just got my 1600 psi Ryobi pressure washer today after watching your video. I also got the Sunjoe foam cannon and switched it to the 1.1 mm orfice.
Happy you took my advice and started using the sportscar to test. Now you can see the foam
You're blessing Josh! Helping all of us detailers!
Just reminding you on one of your soap challenge videos you mentioned doing a foam cannon maintenance video. Maybe you can possibly added it while doing another foam cannon review.
thanks for the honest review , with the ryobi machine.
I have the Tool Daily which is very similar. I have to adjust to the - for more foam. Still doesn’t make much even after changing to a 1.1. I don’t know how there were so many 5 star reviews…
Same results. I honestly thought it would be more foam. Like you said..mesh might not be woven as tight as some of the others. Hopefully you can get to it and be able to change it and test it with other. Good luck 🤞
Not sure what’s wrong with yours but my Trinova makes super thick foam with my active pressure washer. The only soaps that I’ve used is Mr Pink, Honeydew, and Tough Mudder. All have made super thick foam.
Maybe because since it’s a bigger bottle, you should have started out with more soap. If it’s a 2 liter bottle you had more water in it then if you used a 1 liter bottle. I don’t believe it was the mesh that was the problem.
I have the trinova and agree the build quality is very good, certainly worth the money. However, I switched to 1.1 AND switched the mesh filter and still don’t get the super thick foam, not sure what the issue is but now am becoming curious to solve it somehow. As for your question on how to access the mesh filter, I put mine in a bench vise and backed it off with a big wrench. You can get to it, but it’s very tight, you have to back off one of those brass hex nuts once you take off the black plastic piece. You were on the right track.
My first cannon was the Amazon Tool Daily which is nearly identical to the Trinova. It works OK...consumes a lot of product, though. It came with a defective nozzle which didn't adjust much like yours, but they sent me a new one and was fine. I agree no way yours is a 2L...looks like 1.5L like the Tool Daily. Even at 1.5L it's pretty heavy on a stubby gun. Worth the $25 I paid...I'd say yes. My Griot's Brilliant Finish puts it to shame with foam quality, as expected.
Can you please do a review on the tool daily foam canon on Amazon
Great reviews ! One more thing you may want to ad is a pin gage set to see what hole size actually is. Since most of box info is not accurate. So I would say the holes on tips are not what they say !
I have A Griot's and A Trinova...haven't used them yet. I'm using My MaxShine! I have one for foaming... one for foaming wheels with brake buster or Adam's wheel&tire cleaner.
👍👍
I bought the Trinova and wasn't that impressed even after switching the orifice. I bought a Bravex foam cannon - it comes with the 1.1 orifice and seems to foam much better. I did start having better luck with the trinova by lowering the amount of water in the bottle. The larger bottle size seems to throw off the ratios.
Got the Bravex one off Amazon and really enjoying it. Don't have any anything to compare it to but it foams thick as I expect it to. Funny because the TriNova was also on my list, whew. Could just be a bad one.
I also just picked up a Bravex, very happy with the foam, using P&s Perl and the Ryobi 1900psi pressure washer.
Much better than the tool daily cannon I used prior.
Sorry if I missed it but you should do a video of your TOP 10 Foam Cannons and pressure washers... Or which ones do you recommend... Thx
imjoshhv… To get to the foam filter you need to pull off the back larger oring carefully (pulling off the oring is necessary so your wrench fits flat and also so the oring doesn’t get damaged) and put one wrench on those machined flats - then put another wrench on the flats that you had the wrench on towards the front. Hold the back wrench in the tightening position and use the front wrench to loosen the front section. It’s going to take a some force because the units come torqued down pretty good.
The filter is a standard mesh filter.
Hope this helps!
Awesome thanks so much!!
I have this foam cannon. I changed my orifices out to a 1.1 using a ryobi 1.2 gpm, 2000 psi and i get crazy thick foam with chemicals guys water melon and meguiar's gold class soap
You have to twist the knob all the way to - it’s backwards on that cannon
yeap, same on mine as well when i bought one 1 month ago
What do you mean by "twist the knob all the way to"? All the way to what? Are you saying it's backwards from other cannons and you turn the knob all the way to THE LEFT (counter clockwise, loosen) instead of the typical tightening it clockwise to the right?
@@10SecondZ06 usually you are advised to run it turned all the way to the positive sign + but on this you adjust it the opposite way to negative -
@@haroldwhite7464 no, usually you are advised to close it by turning it in to the right which is negative (-). Negative is less water. You can see in the video that he turns it all the way to the right to close it. Are you saying he should have tuned to the left?
@@10SecondZ06 yep, he turned it the wrong way. I have the Trinova with the 1.1mm orifice, with Mr Pink and my foam is twice as thick compared to what you see in this video.
Josh, I have the TriNova which I bought last year and it works great with my gas powered pressure washer. After watching your review of the Greenworks 1700 psi 1.2 GPM electric pressure washer (from Lowes), I bought it and it works great… EXCEPT it will not produce good foam even after changing the orifice to the 1.1 and even using Adams MegaFoam.
After watching your review of the Griott’s foam cannon, I bought it, installed the 1.1 orifice, but the Greenworks 1700 electric pressure washer will not produce any good foam with either foam cannon so I’m really bummed out about that.
Try the Bravex, great performer at a decent price
Not sure why. I have the same 1700 great works. Cheap FOAM cannon Amazon I get good FOAM
Wondered if you do a video questioning the effectiveness of phone cannon's? I think it's cool, I like spraying the car fully with foam I have to keep going in a bucket except maybe a Rinse bucket once a while.Seems like it can be more efficient. Otherwise I don't think foaming a car actually does anything Is implied
I really think you need to be more consistent on your solution. Instead of using markings on the bottle since every bottle is so different, use an actual measurement and make it the same for all your reviews. Also try all the cannons on different settings. I think you should go through all your "bad" with these new rules and you will get differences
I didn't like it, did have good results even after a 1.1 orifice.
Got the arm and hammer foam Cannon and love it with a 1.1 swap
I had the same issue
Thank you for the review Josh. Have you reviewed the "Ordenado" cannon?
I just add more soap. Change the product to water ratio and it gets thicker.
trinova uses more product than any other foam cannon ive used
Mechanics usually call them JETS, but you can continue to check your ORIFICES if you like.
MJJC still on top for me
This is a rebranded one on Amazon called tool daily, same stuff, I changed to 1.1 orifice, holds like a quart of product but will go through it all quick
Thanks. I looked it up. It comes with a 1.1 orifice too. I was about ready to buy the trinova 1. But if it's the same, and it comes with the 1.1 to swap in period that I'll get that 1
@@miragexl007 yup they're the same, Trinova just gets marketed more because of the name
Unfortunately I only got good results with Adams mega foam. And didn't care for the fan adjustments..
Does more foam mean better? I guess more liquid is better as it may be have better surface tension to break the dust and debris
@Srikanth Prabha
More foam means that it sticks to the surface longer, so the soap can do its job better. More runny means that the soap is running right off pretty quickly.
I have this foam Cannon and I was expecting much thicker, richer foam after switching to a 1, but it stayed runny like in the video. I tried it with Adams strip wash, megafoam and a Maguires soap from Costco and it just didn't perform
Try changing the Foam maker to a more dense one, you can get to the phone maker by taking off the plastic sleeve in the front of the sprayer and unscrewing the tip and it will reveal the foam maker
Great video
What conector adapter feat to that foam canon?
U otfto pull off the adjustable nob. And hold it with a wrench. Then pull the end with a nxt wrench
Is it hooked up to a air compressor?? Or a water hose
Honestly change that soap.That small amount of Mr Pink with that much water is terrible.
Instead of turning the knob to the positive sign(+) it doesn’t foam as much for this one you turn it to the negative sign (-)
Mi-T-M best pressure washer PERIOD
You know how difficult it was for me to find out the answer to what orifice this came with?- very hard , no one had answers even the sellers. Thanks for answering the size
I've used a $40 foam cannon and a $9 one..after putting the 1.1 orifice in them, I can't tell any difference. That orifice is the only thing that matters unless your using a powerful gas washer that does over 2000psi. It's weird you saw no difference...you should maybe change the foam mesh piece that's on the other end of the housing.
So what orfice should I use with a gas pressure washer with 2300 psi? I do have a pressure adjuster on the handle too
@@VegasStacker702 I think 1.1 should still be fine because you want it to be small as to get more foam out of it. You could buy a 1.1 and a 1.2...on electric pressure washers there's a noticeable difference between 1.1 and 1.2
What foam cannon do you recommend for a 2.5gpm .. 3200psi gas pressure washer?
Mine works real good
Great review! Bummer about the foam.
Hey, can you please fix the link to the 1.1 mm orifice, it goes to a blank page on Amazon. Thank you
Whats the best cannon to use with the 1600 ryobi pressure washer?
Well that was disappointing foam, can’t win them all, great review 👍😁
Mine didn't come with the tube. Now I know why it wasn't working for me.
yea that will do it
I'm pretty disappointed in mine. Got a new orfice after watching your other videos and it's still not great. Added more soap and it's still runny. Waste of money.
I like 👍 the trinó va perfecto 👌
Wow mind does not have plastic threads
6:45 "First things first guys, let's go ahead and check the orifice"..🔎No, should put on gloves before that. 👍
Griots still king
👍👍
Amazon cannon had far better results
Not impressed wit that cannon I paid less for the one I bought and mine blows that one away
sheesh
1st
👍