After removing the original LCD, take a fine point sharpie and go over top of the display flex cable before removing it from the iron bar; this will help you line it up properly because if it's off EVEN SLIGHTLY, you're going to have issues with light leakage or the screws not going in properly. When putting the iron bar back on, line up the end holes with the (+) on the new LCD. TEST the display before removing the adhesive cover. There's nothing worse than adhering it down and having it not work then potentially breaking it when opening it back up and not being able to get a refund because of it.
@@inobevious8913 If you're talking thickness in terms of "length", for the bar, I use 5mm, but to go around the frame, I use 3mm. I start on the bottom and if I'm replacing the diffuser sheets, I go up to about a quarter inch before the tabs that hold them in place start on each side, then finish going from that ending point to the top after I've layed them down; otherwise, I run it all the way up and then go to the top corner and run it above the camera to the other corner.
@@dta8080 Hi, DTa, this tool is not sold on Taobao, but you can enter our purchase link and ask our online service for more details. Thank you for your comments. : )
In my opinion the most difficult task in retina screen replacing would be to not contaminate the backlight diffuser. Using an excess of alcool would mess up everything as well as touching it or punching it with the tweezers. The tool is nice but I don't think it will be enough to accomplish the task in the proper way...
Luigi Mazzoli your right, nothing special about their new tool, its like any thin prying tool in the market like iflux, plus its the same difficulty even with their method 😁
Hi my macbook lcd is broken, but not the glass panel, is it possible to just replace to the lcd? if so, how much would that be? and if not, what will be the price be for the whole display repair?
Greetings, I have a Mac like the one in the video with the following problem:The screen only works if its not extended past a 45 degree angle, If set to above 45 degree angle it will freeze up and show lines. But once set back below the 45 degree angle it works fine. Based on your experience, where could the fault be?
@@efxcomputer4054 I did the replacement. There were a lot of similarities, but it was a bit trickier with my model than the one shown. It's definitely doable though
请问下这个薄片叫什么名字？我想淘宝但是没找到. 谢谢了. what's the name of the air slice that was used to separate the lcd from top case in Chinese? I am looking to buy one just in case the flex cable on my MacBook died because of the shortened lcd cable.
Hello - I’ve an issue of damaged screen and I need to reset my password using Apple ID through recovery window on MacBook Pro 2016 16 inch. The recovery view of utility window shows up on the damaged laptop screen and not on extended monitor. If I remove the display connection only , without removing battery and Wi-Fi, will that transfer entire display on extended monitor, enabling me to see recovery screen and reset password
@@KurtBarcelona I have been using feeler gauges on iPad surface pros surface book and a few newer imacs and they work great. I use the thinnest one I can get away with. But be careful not to insert too far. And because the feeler gauge I am using is so thin if you push took hard you will fold it over.
@@MrOgger151 oh nice feeler gauges are cheaper (ten times cheaper) than the air mac part the video is using. Ill just use feeler gauges instead. Thanks!
Vasya Belov to show what the whole procedure is. As you said, cleaning the contacts would probably be enough but they wanted to do a tutorial o changing the screen
The problem is this is a very expensive repair the chance of failure and parts is high... Since screen is expensive and hard to get... It just be easier and cheaper to swap the whole top half off a used broken or locked unit and be done with it..
sujeet pandey did you manage to buy the LCD from any website?, I am looking for the A1502 Model (late 2013 MacBook Pro Retina display but I can not find it anywhere. thank you!
For quicky ordering, please feel free to visit REWA Online Shop ( shop.rewa.tech ). Any further demands please contact us at sales@rewatechnology.com Thank you :)
REWA Upgraded Repair Training Course - 2019 June Schedule
* iPhone Logic Board Repair (Beginner/No Experience), Jun. 10th - Jun. 15th, $1499
* High-Level iPhone Logic Board Repair (For Level 2 or above，1 Year Chip Level Repair Experience Around), Jun. 17th - Jun. 21st, $1199
* MacBook Logic Board Repair (Common Repair Solutions Related To Logic Board), Jun. 24th - Jun. 29th, $1499
* Broken Glass Refurbishing Training Course (Cracked Screen And Back Glass Refurbishing), 5 successive days in June, $1200
For the details: bit.ly/2WQkHAI
Enroll Now: bit.ly/2QpPLVD
Any further questions please contact us at: training@rewatechnology.com
REWA Technology where can I get the LCD screen A1502 model for the late 2013 MacBook Pro retina?, thank you!
After removing the original LCD, take a fine point sharpie and go over top of the display flex cable before removing it from the iron bar; this will help you line it up properly because if it's off EVEN SLIGHTLY, you're going to have issues with light leakage or the screws not going in properly.
When putting the iron bar back on, line up the end holes with the (+) on the new LCD.
TEST the display before removing the adhesive cover. There's nothing worse than adhering it down and having it not work then potentially breaking it when opening it back up and not being able to get a refund because of it.
Good tips
how thick of an adhesive tape should be used? 1mm?
@@inobevious8913 If you're talking thickness in terms of "length", for the bar, I use 5mm, but to go around the frame, I use 3mm. I start on the bottom and if I'm replacing the diffuser sheets, I go up to about a quarter inch before the tabs that hold them in place start on each side, then finish going from that ending point to the top after I've layed them down; otherwise, I run it all the way up and then go to the top corner and run it above the camera to the other corner.
Nice tips, helped me!
Can you use a heat mat like for phone and ipad lcd replacement?
FINALLY IVE BEEN WAITING SO LONG FOR SOMETHING LIKE THIS TO HAPPEN
MacBook Logic Board repair Training Course is coming. Check the link and book now: bit.ly/2CbDDSN
can u do video on these touchbar backlight issues from the lcd flex?????
Can anyone just answer this question
What is in your hand like the watch ??
That's Anti-static Wrist Strap: bit.ly/2LyJAyn
Here for the Air Slice Tool Set：bit.ly/2KVK4zp
Great job guys can I buy this thing off Taobao? Or do you ship to mainland also?
@@dta8080 Hi, DTa, this tool is not sold on Taobao, but you can enter our purchase link and ask our online service for more details. Thank you for your comments. : )
you guys did the unthinkable f u apple making me buy a new laptop because of a broken screen and dented botom panel
What tools do you use to test a screen without having a logic board handy?
In my opinion the most difficult task in retina screen replacing would be to not contaminate the backlight diffuser. Using an excess of alcool would mess up everything as well as touching it or punching it with the tweezers. The tool is nice but I don't think it will be enough to accomplish the task in the proper way...
Luigi Mazzoli
your right, nothing special about their new tool, its like any thin prying tool in the market like iflux, plus its the same difficulty even with their method 😁
I really hope Louis Rossmann is sees this.
yes send to apple care.
you are most welcome rewa technology
Hi my macbook lcd is broken, but not the glass panel, is it possible to just replace to the lcd? if so, how much would that be? and if not, what will be the price be for the whole display repair?
Greetings, I have a Mac like the one in the video with the following problem:The screen only works if its not extended past a 45 degree angle, If set to above 45 degree angle it will freeze up and show lines. But once set back below the 45 degree angle it works fine. Based on your experience, where could the fault be?
That's an LCD issue; I work for AGiRepair and have repaired literally thousands of MacBook LCDs and I've seen this issue many times.
These are fixable. #dustgate issue google for info.
how to enable true tone on macbook air m1 after display replacement
which camera u use for video recording???
Amazes me how people are able to do this. Even with the right tools I probably would have deformed the logo strip.
you need to practice
Вот оно решение flexgate 😂а качество отражателей не показал так как после такой замены остаются следы вскрытия !
)))) я вас тут нашел)))
I have MacBook Pro 2019 screen scratched. where to buy LCD from ? and I guess it can be repaired like you suggested. Thank you :)
Your reparing tools is awesome
Thanks, Saddam. ; )
I like the fact you didn’t use a heat gun to remove display glass.
Do you have an updated video for A2442 LCD only repair?
a little toc listing the individual steps in the video would help navigate the video. ie.
3:14 π display asm removed from body
Great video. Is webcam is linked to the board on T2 MacBooks? I am not seeing webcam after screen replacement on 2019 T2 Air
2018 and 2019 macbook air screen looks same but will have issues with camera and kb backlight if installed in different year
wil 0.1mm work for disassembly tool?
Will replacing the lcd on a 2018 model a1989 be similar to this repair?
It would be best to tear a damaged screen to figure it out. I am assuming it would be same if the part is available for sale.
@@efxcomputer4054 I did the replacement. There were a lot of similarities, but it was a bit trickier with my model than the one shown. It's definitely doable though
Nice job!! i will try it out :)
Thank you
How long take this replacement ?
half an hour.
@@rewatechnology2008 with the right tools of course
I have a question: where can I buy these layers behind the lcd inside of the display case? In my case they are broken and I need new ones...
Nice video sir
I like the fact you didn’t use a heat gun to remove the glass from the lcd.
e
请问下这个薄片叫什么名字？我想淘宝但是没找到. 谢谢了.
what's the name of the air slice that was used to separate the lcd from top case in Chinese? I am looking to buy one just in case the flex cable on my MacBook died because of the shortened lcd cable.
拆機鋼片
@@kuroli0108 谢谢回复。我找到的跟up主用的不是一个东西 我想买他们用的那款。请问你还有线索吗？
Amazed... it's a craft.
How much does lcd replacement cost for 13inch mac book pro
请问哪里可惜买到air slice?
Hello - I’ve an issue of damaged screen and I need to reset my password using Apple ID through recovery window on MacBook Pro 2016 16 inch. The recovery view of utility window shows up on the damaged laptop screen and not on extended monitor. If I remove the display connection only , without removing battery and Wi-Fi, will that transfer entire display on extended monitor, enabling me to see recovery screen and reset password
would you be able to do an iPhone X Face ID Not Working After Repairing fix i get the face id is unavailable error. thanks
Hi，StreetLess, here is the video for your reference: th-cam.com/video/bJCuMFeUiGU/w-d-xo.html Have a nice day! ; )
@REWA TECHNOLOGY How many mm does the used tape have? 10mm or 5mm? Thanks!
hello. after replacement my lcd bezels has light leaks some points. How can I fix it. Its very annoying. I already assembled my screen :(
can we use monitor only to pc because the logic/motheboard macbook was failed
Dam i have been using .05mm feeler gauges before I new this existed.
do feeler gauge sets work? or is it inconvenient?
@@KurtBarcelona I have been using feeler gauges on iPad surface pros surface book and a few newer imacs and they work great. I use the thinnest one I can get away with. But be careful not to insert too far. And because the feeler gauge I am using is so thin if you push took hard you will fold it over.
@@MrOgger151 oh nice feeler gauges are cheaper (ten times cheaper) than the air mac part the video is using. Ill just use feeler gauges instead. Thanks!
I have a MacBook pro flexgate issue can i get your contact gmail i have some question?
@@MrOgger151 can i get your gmail?
do feeler gauge sets work? for 0.05mm?
I would avoid using metal because you can damage the backlight
Why do you replasing screen ? Just clean contacts
Vasya Belov to show what the whole procedure is. As you said, cleaning the contacts would probably be enough but they wanted to do a tutorial o changing the screen
@@Jimbokoln no, the screen flex cable are damaged they need a new screen. or replace the screen ruban but nobody has done it yet
After replacing the lcd, the lid won't close fully. Any idea why?
2016 Macbook 13 -- where to buy repair screen flex cable?
The problem is this is a very expensive repair the chance of failure and parts is high... Since screen is expensive and hard to get... It just be easier and cheaper to swap the whole top half off a used broken or locked unit and be done with it..
Sir whare to buy the screen ..?
sujeet pandey did you manage to buy the LCD from any website?, I am looking for the A1502 Model (late 2013 MacBook Pro Retina display but I can not find it anywhere. thank you!
There is even for MacBook 12 ?
please help me 🙏,, If the screen has stripes when the engine is hot, what's wrong with that? but if the engine is cold, it's normal,
tried this, cracked the display in about 17 different places, must not me advanced enough to do a repair like this
what are those sheets under the display please
@5.27
Backlight , diffuser,etc sheets
This repair is much easier with a ipad heating pad to 75 C wearing gloves
Nice coming
sorry after changing the display works fine but the camera does not turn on someone knows what happens or how can I fix it?
Thanks a lot
Why someone use that?
where do I buy the flex cable?
But first check this seller
how to by screen macbook pro
if i replace my mac book air's screen but get a whole new panel with the lid and everything will i lose true tone?
Depends on the screen you are getting. All of them comes from China. Most of them shows true tone but not works like as in original
Great ✊
Need A1707 display plzzzz
Rewa 👍🏻👌🏻
Rubber gasket can get separate
Long nails is recipe for success)
i literally laughed out loud like im crazy
lol I ripped mine apart trying to remove it. now i just removed the screen entirely and use an external display XD
Disassembled the lcd but now its not fitting in 💀💀💀
Where can I get the lcd
For quicky ordering, please feel free to visit REWA Online Shop ( shop.rewa.tech ).
Any further demands please contact us at sales@rewatechnology.com
Thank you :)
hola amigo buen vídeo pero no se pueden los subtitulo solo dice música y no se entiende un saludo de mexico
отличное видео, собирал экран именно по нему!
спасибо!
but not asembly the original display
Hello, please can anyone help me to find glass for A1707? im googling for hours with no success. Thank you!
Hello, please contact us at sales@rewatechnology.com with your purchase demands. Thanks :)
Not bad)
Serious Question if i send you a phone can you edit it on the Specifications that i ask for money
14寸的Pro
Which screwdriver you used ?
For the details of screwdriver, please check this link as a reference.
( shop.rewa.tech/search/screwdriver )
Thanks :)
Sir
Mac Pro та штучка
Am I the only one from Nigeria here 🙄🙄🙄
👌👌👌👌👌
❤
I want to train in your river
We do offer training courses. You should come. Here's the course details for your reference: bit.ly/2V5FkHF
im fucked