The WORST Axle Bearing I've EVER SEEN - How To REPLACE Classic VW Swingaxle Axle Bearing
ฝัง
- เผยแพร่เมื่อ 21 ธ.ค. 2023
- Taylor replaces a bad axle bearing on the mystery beetle.
Fritz Tools Bearing Puller -
www.thesamba.com/vw/classifie...
Follow @wickedwerks on Instagram! - ยานยนต์และพาหนะ
That puller is a game changer
Really is! He’s got a couple of helpful tools
perfect timing, I was looking at the 59 and both sides have tell tale signs that the seals are both leaking. I probably should NOT flat tow that home 30 miles. Thanks !! And I think I did buy that same puller off the samba bceause getting that f n bearing off is a bear - I welded to my first one (62 bug). But we are to get smarter as time progresses.
What a fantastic puller I've spent hours getting those bearings out!!
Great How To Video. Im glad the tool worked as intended. I appreciate the shout out and link to the ad. Keep on Veedubbin!
Of course! Thanks for watching! ✌🏻
Happy Holidays sir. 🎄
Wow !! Like you I’ve never seen a leak like that ,good that job cane to you and fix . Happy new year
Job well done, amazing how much easier it is with the correct tools. Have a good Christmas, bearded one.
This is the very next job I need to do on one of mine. Great video, subscribed. Many thanks
You’re welcome, thanks for watching and good luck!
Great job !
Another great video! I noticed the rusty sludge started oozing out of the bottom of the new bearing. Where was the rusty sludge coming from? Is the residual sludge just so nominal that one need not worry about it? I'll be doing all this on my Beetle sometime in the next few months so I'll put this video and your comments in my how-to library.
It’s coming from the axle tube. I sprayed the bearing out with brake clean before putting the cap back on. Once I get a couple 100 miles on it, I’ll change the gear oil again. Only way to get the majority of the schmoo out with pulling the axle tube to wash it out. This video will NOT apply to your Super Beetle as you have an IRS rear end. I have a video on doing the rear suspension on my bay window Bus that is applicable to your Super. Good luck!
@@wickedwerks Thanks for the great response and great advice. I will go look for that video and put that in my how-to library!
👍👍
According to the Bentley manual for pre 59 cars, they don’t show the paper gasket for the carrier area. Would you use it anyway? Bentley only shows the O ring seals.
Yes.
Thanks. What sealer do you use on the paper gasket?
@@jeffbannon1345 permatex “right stuff”
@@wickedwerks thanks!
Where can I get one of those pullers
Link in description for an ad on thesamba.
Sounds like you're fighting the weather also
Yeah, it’s stupid cold and that propane heater doesn’t do much 😂
Should you not have put plenty of bearing grease into the new bearing before sliding it onto the shaft?
No, bearing is lubricated by the transmission oil.
Sehr gutes Video.. 👍 weiter so 🤙🏻Abonniert ✌️
hammering a new bearing into place, really.
If it can’t handle a few light taps with a hammer, it shouldn’t be on the car.
@@wickedwerks And when they are hard to fit on the shaft ,hammer more,come on, teach the right way, or not at all. Bound to be new guys/girls doing this.
Sometimes I wouldn’t mind seeing how you clean parts and stuff.
Sometimes I do, most of the time I can’t be bothered 😂 in this case I just used simple green, hot water and a bristle brush. Hit the seal surfaces with 0000 steel wool.
really.../? .brake clean, cotton rag... picture that..
@@rrs1550 everyone has their own way.
Great video. I just picked up a 1960 VW and it’s making a weird sound from the rear.
I found this video on TH-cam and it’s exactly what mines is doing
th-cam.com/users/shortsjDOTO4ipL8U?si=Uq1l8wZVukgbRqu9
Is that the same thing yours was doing? Thanks