You're the real MVP! My G400s resurrected this way, after editing onboard GPU VRAM on BIOS (custom BIOS), looks like it bricked the EC. Now my old G400s live again!
Another question it can program only ene chips. Like ite newton or another io chips. Kbc 9012 programs pin same in io or not. Another kbc 9012 chip with other motherbord it change only keybord conecter pins or not
@@Pixell_Eletronica eu fui fechar um notebook da acer e5 473 e ele da uma luz bem fraquinha na tela, e tipo como se ligasse sem as lampadas, mas trava ali n da pra ver as letras no fundo da tela. Acredito que seja a bios do super IO mas não sei regravar ela com meu regravador Ch341
@@Odepressivocompusivo Entendi mais menos seu problema pelo o que voce explicou, mas acredito nao ser a bios do super IO, acredito ser um problema diferente, da Tela ou Flat cable da tela, ou do Inverter que fica ali embaixo da tela. Verifica primeiro esses componenentes pois o sintomas de um notebook sem gravacao no Super IO, é de nao ligar nada, nem ao menos acender o Led de liga e nem girar a ventoinha. Se o seu esta ligando, parece nao ser o IO.
how to program kb9052qd, is there a schematic because in neoprogrammer and as programmer there is no kb9052 series how do you have a solution or a schematic
It is certainly possible to burn an ATMega328 or Tiny85 with a bootloader and set the fuse. In serial mode it is then possible to load a program with RX / TX.
@@Aditya11ttt Could you help me just by telling me which signal is the one that goes to gnd of the kb9028 I have the other 4 signals but I can't find the gnd. greetings from Mexico
i try this method for kb9026q using ch341 with neo programmer...in neo just detect kb9012 in list ic...I use as kb9012...and can read write...but many problem on my board...can't see succes or not...
@@Aditya11ttt I've connected the CH341A GND to KSO3 PIN 18 of KEYBOARD connector and connected the board's GND to KSO3 PIN 18 of KEYBOARD Connector. Is this correct?? My laptop charging led stopped glowing! but it was glowing before. But still iam getting IC Not responding 😒
I've tried connecting my Motherboard to TL866II Plus ICSP Connector but it reads with 00's. BTW I don't use SPI Driver for TL866II PLUS. I'd connected the KEYBOARD Pinouts directly to the ICSP Connector of TL866II PLUS! Please Help
Good evening, I'm looking into doing this with a 9028 chip but I have heard from people that the CH341 works on 5v, and these ENE chips are 3.3v chips. I assume it works OK anyways?
Try yourself | and check | if u keep listening the people throughout your life you will only keep listing throughout your life ! If wanna learn something to it yourself and test and learn ! Good luck 🙂
Ci have two questions. 1. How do I know 5 wires data connection..means which one is gnd ,di,do,mois,mosi . 2. Can be possible re program ite,nuvoton smac iochilwith thehelp ofch314
Hi, is it possible to program an Atmega32L and Atmega32A QFP-44 chip with this programmer, and how to prepare it for this? Thank You in advance for Your help!...
Amigo vi seu comentário no outro, pelo jeito está faltando Backlight no seu notebook? Ele deu vídeo normal externo? Você precisa desmontar seu notebook e medir as tensões Lvds
@@DiaconoAdao ele não da video em monitor externo e nem acende o botão numloock do teclado externo, é tipo como se ele acendesse os leds la no fundo da tela mas trava e fica ali, quando desliga da pra perceber que a tela apaga. Ja tentei ver se aparece letras no fundo mas não, parece que ele fica travado nisso
Amigo se ele não da vídeo externo então tem que baixar o esquema elétrico e ver o que está faltando... não adianta regravar o super io sem saber o que realmente falta
My keyboard and touchpad not working Then i open laptop top cover and this chip is damaged Is it used for keyboard and mouse But laptop working with external keyboard
This would have been a good video if you removed all the 'course' ads u put in there.. and why did you put the logo bigger than the video? around 11:20 ? makes no sense... u coulda offered the course at the beginning and the end.. short n sweet... i realize this was 2 yrs ago.. but c'mon... more content... less ads... then maybe u will *GAIN* subscribers
Very good and clear tutorial. I successfully fixed a laptop after watching this. Thanks a lot!
You're the real MVP! My G400s resurrected this way, after editing onboard GPU VRAM on BIOS (custom BIOS), looks like it bricked the EC. Now my old G400s live again!
Thank you for this tutorial, very useful, this is very important for the community.Greetings from Venezuela
thank you i just saved a laptop because of your video
Thanks a lot 🙏 very helpful, in the newer ch341a models it's a lot faster to program, it took me around 10 minutes
It’s the cheapest programmer , if u are professional buy a good programmer simple !
I was not complaining about it and have many pro programmers 😊
Very informative. Its very explain well thanks bro keep it up. So amazing at awesome
Thank Bhai you are great and great work
Thank you Sirji..Wonderful details
Gracias amigo me quitaste las dudas, tenia pensado comprar un SVOD (300USD) pero al ver que era un SPI norma justamente pensé en el ch341a.
English please
@@Aditya11ttt Thanks, you saved me from buying a 300USD SPO programmer.
It was a simple SPI protocol of the same ch342a
Make sure you select the " detect KB..." option, under "Options> detection options", I've spend hours not able to detect the KB90 chip...
Best tutorial thanks brader
HAPPY IT'S WORKING.. KBC9022 but takes more Time
Already said in the video it takes time but will work ! Not professional ! But ok for temporary work or low cost work !
your the best, thank you
I was thinking about the benifit of those pins side of the programer.Thank you👍
Very nice. Thank you.
Is working 💪 good for you
Is this same with ene kb9022q? Dlid4/d5 La-g202p
is there a dedicated website where you can download the SIO chip programs?
great work tanks
Just great!
Congratulations very good---Muito bom funcionou perfeitamente
Very useful and informative.... Where do we get those Jumper Connector Cables ?
We sale !
Good Job
Excellent tutorial. Thank you so much for posting. How long would the svod3 tool take for the same process? Which tool is the fastest on the market?
SVOD 3 is best ! And easy to use if need contact via what’s app ! For pricing and details !
Hello Sir Aditiya hope u r good in health i just want ask can we also program ITE 8 series chip with RT809F programmer
Did you flash the same backup file?
Hello, good video, I congratulate you. Could you try it with the kb9542qe? Would the same method work?
Thank you for your helpful video, can we program other super IO chip with ch341a programer?
No only ene
Another question it can program only ene chips. Like ite newton or another io chips. Kbc 9012 programs pin same in io or not. Another kbc 9012 chip with other motherbord it change only keybord conecter pins or not
Nuvoton no | ite no | Ene yes
@@Aditya11ttt So there is no way to program ITE or Lenovo EC chips using this device (CH341A) connecting it in a different way? Thanks in advance!
@tomaszpluta5839 via this programmer no for now
Execellent. BR. Obrigado cara, deu tudo certo com KB9022 da placa LA-C571P. Thank you very much.
Rodrigo, você pode me ajudar?
Eu estou com um problema e acredito que seja a bios do super IO mas não sei gravar com minha gravadora que é dessa simples ch341
@@Odepressivocompusivo Opa beleza? Qual o seu problema?
@@Pixell_Eletronica eu fui fechar um notebook da acer e5 473 e ele da uma luz bem fraquinha na tela, e tipo como se ligasse sem as lampadas, mas trava ali n da pra ver as letras no fundo da tela. Acredito que seja a bios do super IO mas não sei regravar ela com meu regravador Ch341
@@Odepressivocompusivo Entendi mais menos seu problema pelo o que voce explicou, mas acredito nao ser a bios do super IO, acredito ser um problema diferente, da Tela ou Flat cable da tela, ou do Inverter que fica ali embaixo da tela. Verifica primeiro esses componenentes pois o sintomas de um notebook sem gravacao no Super IO, é de nao ligar nada, nem ao menos acender o Led de liga e nem girar a ventoinha. Se o seu esta ligando, parece nao ser o IO.
Hi there , please make more tutorial video in English . thnakyou
Will be in Hindi and English !
i got SIO chip ITE . Did you know proframer can suppeort for that chip
how to program kb9052qd, is there a schematic because in neoprogrammer and as programmer there is no kb9052 series how do you have a solution or a schematic
very good video, i have been waiting for this for long, thanks. please the link to the programmer software.
in the link added check!!
Thanks. Does it work with IT8227E?
No
Will it program 1gb bios chip??
i have the Xgecu TL866II plus, it works for program ENE KB9542GF?? where i can conect the VCC line on my programmer??
Use direct adoptor to MBD ! Dc in vcc no need from programmer
Thank you so muche for your efforts. .. please from where I get the flashing bin file of ..KB9016QF A3
Sorry to say that sir getting bored with your advertisement..but your concept always helpful ✌️
For add free stuff pay 💰!! 🤓
do you have a video for ITE chip?
This programmer can’t flash ite
Will this work for KB9022?
Yes
it can be same ite 8226 ?
Very nice
Please I want an explanation for connecting the Atmega649v processor in the same way, if you please
Not possible in this programmer !
I need to program and ec for a all in one board, does not have keyboard port, i have ch341a, svod3 and rt809h's pcb for kb9012, how can i program it?
Is the pinout of the ene chip the same for all ene chip sir? Or they are different according to their part number?
Pin out are same for all ene. But keyboard pin out can differ
@@Aditya11ttt thanks..but where can we download firmware for the ene chip if it is corrupted?
We have paid service
Alternatively u can try google ! For free !!
It is certainly possible to burn an ATMega328 or Tiny85 with a bootloader and set the fuse.
In serial mode it is then possible to load a program with RX / TX.
Try ! I have not tested !
Yes yoy can use serial mode set by jumper
Thanks you
Hi, I'm from Bangladesh. Can i use ch341a and neo-programmer for flash ITE chip? In software not available ITE chip ID.
Ch341a is not for ite
Program nuvoton pin ?
@@Williamross-v3x can’t
Can the same approach be used to flash ITE IT8587E?
No , you need svod 4
@@Aditya11ttt
Thanks
ITE & Nutoton IO ka program Ch314a se hoga keya?
No
thank you bro
i am asking why i cant detect kb3930 ????? error ic not responding
Kb90xx is supported about kb39xx I guess not
@@Aditya11ttt thank you bro
is programming needed for intel 945 boards SMSC SCH5127 super IO chips ? plz reply asap.
I don’t think so !
it works with it sio?
the ch341 can program a it8886he ? And thanks for the contribution.
No
Ch341 programber support teaxs, microchip all device ?? Lqfp80, lqfp64 pin ic?? Sir
No
What programmer used in professional work? That compatible with almost every chip on the planet?
Bee programmer
Svod 3
Rt809h
And there are many other !
@@Aditya11ttt thank you for the answer I'm gonna buy one of those programmer I never encountered a IO chip problem yet mostly are corrupted bios.
Sir i have a doubt, is it also match ite8056 io ic?
Not clear
the ch341 can program a ENE KB9028Q C? And thanks for the contribution.
Yes
@@Aditya11ttt Could you help me just by telling me which signal is the one that goes to gnd of the kb9028
I have the other 4 signals but I can't find the gnd. greetings from Mexico
@@gerardomartinez6508 gnd u will get in whole MBD ! And it’s every where connect anywhere ! Gnd is common !
Same
@kd drama kb9028q c
nombre pin ec ch341
EDI_CS 59 cs
EDI_CLK 60 clk
EDI_DIN 61 mosi
EDI_DO 62 miso
ENEABLE 42 gnd
luck.
Excellent video. I have tried to do it but when I start to read the chip the computer shuts down after a few seconds
Check with another system
Helpful video
Are the wires specifically designed for the program
Where to buy the wires
Thanks
Normal wire
hi.any info if it can flash kb9028q ?
Try same method for all ENEkb90xx
Will EC chip fail during Bios Update ? My Laptop does not turn on after Bios Update
Possible
what is keyboard pin pitch? 0.5mm? Not going to solder, just get FPC/FFC 26 pin cable and run to CH341a
hi, does it work for ite super io?
No
what is the connection if the keyboard if 32 pins
Check with schematics
Hello, I need dump for ec kb9022q D for dell 5565 board is BAL23 LA-804P, do you have it? thanks
Write on what’s app or telegram
Will be prepaid service
i try this method for kb9026q using ch341 with neo programmer...in neo just detect kb9012 in list ic...I use as kb9012...and can read write...but many problem on my board...can't see succes or not...
First solve the “many problems” than re try again
Please clarify the GND Connections for BDL50 LA-D702P. For CH341A. Neo programmer ic not responding error please
Gnd is common for all ! Take from any corner of MBD
@@Aditya11ttt I've connected the CH341A GND to KSO3 PIN 18 of KEYBOARD connector and connected the board's GND to KSO3 PIN 18 of KEYBOARD Connector. Is this correct??
My laptop charging led stopped glowing! but it was glowing before. But still iam getting IC Not responding 😒
I've tried connecting my Motherboard to TL866II Plus ICSP Connector but it reads with 00's. BTW I don't use SPI Driver for TL866II PLUS. I'd connected the KEYBOARD Pinouts directly to the ICSP Connector of TL866II PLUS! Please Help
@Individual.Eleven no idea with tl866ll
@Individual.Eleven no idea with tl866ll
Good evening, I'm looking into doing this with a 9028 chip but I have heard from people that the CH341 works on 5v, and these ENE chips are 3.3v chips. I assume it works OK anyways?
Try yourself | and check | if u keep listening the people throughout your life you will only keep listing throughout your life ! If wanna learn something to it yourself and test and learn ! Good luck 🙂
tried it but ic not responding ene kb9022c
Ci have two questions.
1. How do I know 5 wires data connection..means which one is gnd ,di,do,mois,mosi .
2. Can be possible re program ite,nuvoton smac iochilwith thehelp ofch314
1. It’s written on pdf
2. Only Ene others not !
@@Aditya11ttt can I have the pdf plz..
@@devsabuj4818 search as per model !
Hi, is it possible to program an Atmega32L and Atmega32A QFP-44 chip with this programmer, and how to prepare it for this? Thank You in advance for Your help!...
No
@@Aditya11ttt What programmer do i need?
Only it can program kbc 9012???
Enekb90xx
@@Aditya11ttt sir Does it support kbc enekb9028 chip?
Hello This usb programer can read/write ite8518E?
Nope
and if instead of a laptop, it was a desktop motherboard, would there be any way to reprogram it too?
Yes
can you program IT5570e-128 with ch341a ?
No
Obrigado... Brasil agradece
Vc pode me ajudar? Estou tentando fazer isso
Amigo vi seu comentário no outro, pelo jeito está faltando Backlight no seu notebook? Ele deu vídeo normal externo? Você precisa desmontar seu notebook e medir as tensões Lvds
@@DiaconoAdao ele não da video em monitor externo e nem acende o botão numloock do teclado externo, é tipo como se ele acendesse os leds la no fundo da tela mas trava e fica ali, quando desliga da pra perceber que a tela apaga.
Ja tentei ver se aparece letras no fundo mas não, parece que ele fica travado nisso
Amigo se ele não da vídeo externo então tem que baixar o esquema elétrico e ver o que está faltando... não adianta regravar o super io sem saber o que realmente falta
@@DiaconoAdao vou ter que fazer isso
can it program ite sio for lenovo?
No
@@Aditya11ttt awe, whats cheaper and good programmer sir? It ene programmer or rt809f?
@@aw4106 spi + I2c + ene
my brother can you teach us how to identify CLK MS MSI MSO GND Pinout on any PCB Board ????
Use data sheet of Ic
can it flash the kb930 ene?
If it has flash inside it can !
@@Aditya11ttt Its from a lenovo laptop but I cant reflash it it says not porgrammable in the websites? Im using sas jig
@@Aditya11ttt I didnt found inside it says Icnot supported so I tried sasjig cant flash or write
Than it may be non programmable
My keyboard and touchpad not working
Then i open laptop top cover and this chip is damaged
Is it used for keyboard and mouse
But laptop working with external keyboard
This usb programer can read/write ite8587E?
No
why my ch341 can write kb9022 in few minutes?
I don’t know! May be your programmer connection has issue or it’s super fast
why is not working for kb9026q c? already follow instruction but it detected as microchip not ene sir, any solution?
Try read and write in what it detects and try ur luck, or search new software!
Kbc 9022 it can program or not
Did not test !!
Same protocol !!
Try !!
How can one connect an I2C CHIP TO CH341A PROGRAMMER AND READ AND WRITE IT?
Watch the video on Ch341a
Hello sir, how can i read nand128w3a2bn6 chip by ch341a?
No
Hi friend. I need programmer Mec5035, is possible?
SVOD 4
how to flash it8586
Svod 3
This programer read/write in Winbond 25q128fvsq???
Cesar Cortés Rojas yes
Windows select ic has appear, but ic kb9012 nothing for selected. What's wrong bro ?
🤔
Hi there , where do you download the files from to flash to the ene chip
Have paid support group for bios and schametics pay join get for details contact via what’s app link in the discriptipon of the video
KSO3 is not GND
Need firmware for hard disk ST350413AS JC66 firmware as bios ic is corrupted
What is the problem of that laptop?
Why you repgorm that chip?
Why you reprogram that chip?
Demonstration of how u can program ene io ! Using ch341a
@@Aditya11ttt ahhh ok sir . Good job. So smart
@@Aditya11ttt can you help me of my laptop?
whats the problem with motherboard? dead or..?
Demonstration of how u can program ene io !
This would have been a good video if you removed all the 'course' ads u put in there.. and why did you put the logo bigger than the video? around 11:20 ? makes no sense... u coulda offered the course at the beginning and the end.. short n sweet... i realize this was 2 yrs ago.. but c'mon... more content... less ads... then maybe u will *GAIN* subscribers
2 years old content !!
Vpg😮😮😮😮😮😮😮😮😮😮😮😮😮
Thank you....
how to soft io microchip