Note that if flashrom is giving you an error "Couldn't open device 1a86:5512. Error: Programmer initialization failed." make sure that a jumper is placed on the pins next to the big plastic block. You can clearly see it in the video at 1:30. This changes the programmer device from UART mode to SPI mode and allows flashrom to use it. My device came without the jumper installed and I spent several hours trying to figure out why it wouldn't work, until I came across a patch for the source code of flashrom that hinted there might be a jumper necessary to switch modes.
Good information, I hope those who use CH341a will follow your discovery. Oh, I wish the chip makers would mention these in their tech manuals. Another such example is when I replaced a Compaq mobo which then had a BIOS error "Serial number not found" after a BIOS update. I had to patch BIOS with a 3rd party flash to install (tattoo as they call it) the serial number into the BIOS to bypass the irritating error screen and boot w/o issue.
Thanks for the informative video. Couldn't connect with the clamp, impossible. Mine is defective, the teeth on one side are about 1mm longer than the other. Found another video, check out these connectors, they seem to be quite the find and I will be planning to look into them! th-cam.com/video/r7j7KThqTXM/w-d-xo.html
Awesome video man, you explained it so well even I can do it. Just orderes my CH341A chip and clamp. Thank you very much, hope to see more videos like this one. Cheers!
Thank you for the video! I'm getting a "FW Version Error" message. I am going to try and flash the bios chip with the programmer. UPDATE I was able to flash the bios but had to hold the clip on the chip because it wasn't making contact. Took me a while to figure that out.
@@killerks7379tl be written on the chip the starting number will have either an alphabet followed by 24 or 25 or in worst case just look for the number 24 or 25 on the ic itself
First you can try the autodetect function in the program. The CH341A will only deliver 3.3V to the chip. If you need 1.8V you need an adapter. 5V will require a modification of the CH341A. Other than that all SPI chips should be compatible. It is an interface, and they all use the same pins.
I am encountering an issue where my CH341a disconnects (I get the USB disconnect sound) when I attach the clip to the bios chip on my motherboard. I think it might be drawing to much power?
@@martyhorten3743 Probably a PSU issue. Lots of flat-screen TVs have this issue at some point of their life. It's often because of a dead capacitor which prevents the TV to turn on.
What were the symptoms? I have a LG 38UC99-W that shows it’s getting power (bottom button LED lights up) but it won’t charge any devices and it shows no display or backlight
thank you for your informative video, its about time ,be able to catch up with this as i need it to fix my laptop bios stuck with forgotten password thanks a lot
Hey would this work on an ASUS M2-VM motherboard bios? The Bios is soldered to the board... I'm assuming it would need smaller clips to connect to some of the legs... My BIOS was being upgraded and the entire board got bricked. Truth is, I've moved on to other PCs and even have two other ASUS replacement boards. But lately, I've thought of trying to fix this old one and use it for something like linux or tinker around with steamOS or something. Be fun to actually be able to fix it
where's the info on how to fix the built in 3.3v fail that all of the older versions of this reader have? get te new model ch341a v1.6 ; how can any review about thiis be complete without that info?
Thanks for the tutorial. My thunderbolt controller got corrupted on my laptop and the only way of flashing it is externally. I got the parts. Wish me luck.
THANK YOU for your service to the tech world. Just think how many hours and dollars you have saved people due to your generosity. I love how it didn't work the first time, just like the real world lol. And you remembered to mention possible trip-ups. Outstanding! EDIT: some of the commenters on Amazon mentioned (complained) that they had to physically hold the clamp in place for it to stay. Just an fyi.
Thanks bro I used Asprogrammer to unprotect the laptop vbios chip and clear then write and verify it worked got it to flash up and running. I downloaded Asprogrammer from the github site . Be well bro.
To flash the bios to a laptop do i have to remove the motherboard or i flash it on the laptop with motherboard on by only removing the battery from the motherboard
Tomahawk B450 bricked when I did "instant flash". Ordered the programmer and clip and this video is very informative thank you. Here's hoping it'll save my board.
Thank you, I just bought the programmer to try writing a correct bios to a fake 1060 6GB gpu I bought off ebay and I was wondering how that would work. Hope I find a bios that makes the card being properly detected afterwards.
You should make a video of you doing this with a raspberry pi if you have one. The CH341A isn't even needed if you have a Pi and the test clip. Just have to find a way to connect the test clip to the Pi's GPIO port/header or get just a clip with some female to female jumper cables/wires to connect from the clip the Pi.
Flashrom have problem if u have 4mb chip and 236kb file its can't write but in window its write and work i test it...in flashrom if u do its give u error file size didn't match to chip size i don't know why and the developers didn't fix it ..fow window asprogrammer write and work fine
Can you recommend a good quality programmer and test clip? I know you are using a CH341A, but the ones I am looking at have some reviews complaining of poor quality and excess voltage. I'm wondering if there's a good manufacturer out there.
I have a k5000 graphics card that I want to flash to have Mac boot on it, I bought the 512k chipset since the original is 256k and the file size is slightly bigger. How can I write onto that chip? Also looking at it, it doesnt have a dot in the upper right corner.
Hey my dell 7567 got bricked cause of dells stupid dell support automatically downloading and installing the bios on its own. My previous bios was 1.11.0 is it safe to install one of the older bios or will old bios cause issues?
You're lucky if it works without removing the chip. Often one finds that the other circuitry around the chip make it impossible to provide enough power to the chip and/or enough signal to program it.
I can't use the clamp, the spring is extremly thigh, everytime I put it on the chip it just gets out and it feels and sounds like its breaking the chip.
my programmer doesn't work. It seems that the programmer is faulty. not a single bios chip connects to it. it doesn't read the chip the power light just dims which means that there is a short somewhere. and it doesn't matter which way i put the test clip on it still just thinks that its shorted.
Hi! Great video, I am using the windows version of the program, it's more simple. But after a couple of success, now it's like the clamp doesn't work anymore, when I place it on the bios it always slip me out, it cannot stay firmy on the chip. DO you know why? The plastic is gone? This clamp probably sucks, I don't know if I can find on internet a better clamp. Is it possibile?
hi i need help knowing what bios chip my notebook has its very difficult to read and some of the text is worn off isint there a program or data base i can search for my bios chip name and manufacture ?
Thanks for sharing this on Win/Linux. Do you think I will be able to re-flash a Asus B450F Gaming MB Bios Chip with this? (I bricked it ;) Thanks for Reply, Roger
8:13 Linux already loads the CH341a w/o installing a driver? Nice! "flashrom" is the CH341a driver? If I run MXLinux (or Linux Lite) will the repositories be Ubuntu or any Linux? Thanks!
Greetings, interesting resolve being clueless such a fix existed. Considering I've been spending endless hours attempting to normalize my corrupt BIOS that invaded my gravity standing sideways. I have a dysfunctional Lenovo YOGA 730-15IKB Laptop, question; Are the flasher Test clip Devices universal for all computers or device specific for specific model computers? Thank you very much for posting this vital educational post for all of us, remain well...
the controller is universal, depending on where you buy ot from it will be ready to flash BIOS for motherboard/GPU just double check on your chip what kind of voltage it needs so you don’t fry your chip. It usually comes setup for 3.3/5V but some chips are 1.8V and you’ll need an adapter for them, look up everything before doing the procedure so you don’t have any problems!
those programmers usually run at 5v. that bios chip and most bios chips run at 1.8v you either need the 1.8v adapter or you'll bake the chip... im assuming.
In the file for the 341a programmer, there's a bunch of documents. Read the section on modding for 3.3v use as some devices won't program. If you get any verification errors, check all the options under the write drop menu item. Until I did that I kept getting errors.
Thanks for the sharing. I have 2 questions 1. My bios chip is Mx25L12873, can I replace it by another mx25 bios chip or w25Q? 2. I tried to flash my bios chip using the ch341a and the test clip but after that my laptop don't power on and the charging led is blinking white and orange. Could you please help? Many thanks to all
Great tutorial, buddy! I've got the same ch341a programmer, I know where to start from, but just wanted to confirm, other hackers have used it successfully. Thanks!
Note that if flashrom is giving you an error "Couldn't open device 1a86:5512. Error: Programmer initialization failed." make sure that a jumper is placed on the pins next to the big plastic block. You can clearly see it in the video at 1:30. This changes the programmer device from UART mode to SPI mode and allows flashrom to use it.
My device came without the jumper installed and I spent several hours trying to figure out why it wouldn't work, until I came across a patch for the source code of flashrom that hinted there might be a jumper necessary to switch modes.
Good information, I hope those who use CH341a will follow your discovery. Oh, I wish the chip makers would mention these in their tech manuals.
Another such example is when I replaced a Compaq mobo which then had a BIOS error "Serial number not found" after a BIOS update. I had to patch BIOS with a 3rd party flash to install (tattoo as they call it) the serial number into the BIOS to bypass the irritating error screen and boot w/o issue.
Thanks for the informative video. Couldn't connect with the clamp, impossible. Mine is defective, the teeth on one side are about 1mm longer than the other. Found another video, check out these connectors, they seem to be quite the find and I will be planning to look into them! th-cam.com/video/r7j7KThqTXM/w-d-xo.html
Thank you for this!
wtf how did you clip it so fast man ive been here an hour and im pulling my hair off shits pissing me off it wont clip!
Nice and clear explanation, not top slow or rushed.
Thanks for taking the time to do this 👏👏
Awesome video man, you explained it so well even I can do it. Just orderes my CH341A chip and clamp. Thank you very much, hope to see more videos like this one. Cheers!
Thank you for the video! I'm getting a "FW Version Error" message. I am going to try and flash the bios chip with the programmer.
UPDATE
I was able to flash the bios but had to hold the clip on the chip because it wasn't making contact. Took me a while to figure that out.
Yeah, I'm sketchy about the clothespin clip, as you see he took a few reclippings to get a read.
What is a 24 or 25 series?
its the bios chip model
@@vancabrera8833bro how can i know my chip model ?
@@killerks7379tl be written on the chip the starting number will have either an alphabet followed by 24 or 25 or in worst case just look for the number 24 or 25 on the ic itself
Also helpful vid is in th-cam.com/video/-ln3VIZKKaE/w-d-xo.html , showing what to do if you need 3.3V logic support.
What happens if there's no logo or other identifying information on the IC chip except for numbers?
First you can try the autodetect function in the program.
The CH341A will only deliver 3.3V to the chip. If you need 1.8V you need an adapter. 5V will require a modification of the CH341A.
Other than that all SPI chips should be compatible. It is an interface, and they all use the same pins.
I am encountering an issue where my CH341a disconnects (I get the USB disconnect sound) when I attach the clip to the bios chip on my motherboard. I think it might be drawing to much power?
Where did you get the software that you use on windows, I've not been having luck with the various ones I've tried so far,
please tell me if you find one
@@marcuscoolin yeah, still no luck ae
You helped me to bring a very expensive ultrawide monitor back to life with this brilliant tutorial. THANK YOU!!!
Nice to know that monitors can be flashed, I have a TV monitor that has a power light, but not turning on - Maybe a BIOS fix?! Thanks!
@@martyhorten3743 Probably a PSU issue. Lots of flat-screen TVs have this issue at some point of their life. It's often because of a dead capacitor which prevents the TV to turn on.
@@lululock Yup have changed out caps for pennies on TV boards. Even hot wired one on an old rear projection whose vertical hold was kabloey.
What were the symptoms? I have a LG 38UC99-W that shows it’s getting power (bottom button LED lights up) but it won’t charge any devices and it shows no display or backlight
thank you for your informative video, its about time ,be able to catch up with this as i need it to fix my laptop bios stuck with forgotten password thanks a lot
Hey would this work on an ASUS M2-VM motherboard bios? The Bios is soldered to the board... I'm assuming it would need smaller clips to connect to some of the legs...
My BIOS was being upgraded and the entire board got bricked.
Truth is, I've moved on to other PCs and even have two other ASUS replacement boards.
But lately, I've thought of trying to fix this old one and use it for something like linux or tinker around with steamOS or something.
Be fun to actually be able to fix it
Can I flash bios with Arduino or raspberry pi pico ? Please help
where's the info on how to fix the built in 3.3v fail that all of the older versions of this reader have? get te new model ch341a v1.6 ; how can any review about thiis be complete without that info?
How do you know the difference between the 24 and 25 version?
Bro if u knowed tell me
Thanks for the tutorial. My thunderbolt controller got corrupted on my laptop and the only way of flashing it is externally. I got the parts. Wish me luck.
The flash worked! Now to see if it fixed my issue.
How do you know if you have a 24 or 25 series?
Find it,,, look up the numbers and letters.. if it's Mac. Be a genius 😂
i need to know how to download flashrom on windows. their site is no help to me and asprogrammer constantly shows new chips
does this device work for 16 pin bios chips?
assuming you have the correct test clip anyways
Sir is there a difference between the EZP2019 and CH341
Sorry, don't know brother... Google seems to say they are different, but I have no experience with EZP2019s
@@deftdawg
Can I flash it with linux if I have Ubuntu on an external SSD drive?
THANK YOU for your service to the tech world. Just think how many hours and dollars you have saved people due to your generosity. I love how it didn't work the first time, just like the real world lol. And you remembered to mention possible trip-ups. Outstanding!
EDIT: some of the commenters on Amazon mentioned (complained) that they had to physically hold the clamp in place for it to stay. Just an fyi.
For sure clamping can be tricky, especially if there's a bunch of other components around it
mine is CH341B* its B! what now?
How to download a bios file for hp elitebook 8470p
Why the clip not work on another programmer?
Can u provide links for the windows drivers and software you used.
Here you go: neon.kde.org/download
Thanks bro I used Asprogrammer to unprotect the laptop vbios chip and clear then write and verify it worked got it to flash up and running. I downloaded Asprogrammer from the github site . Be well bro.
To flash the bios to a laptop do i have to remove the motherboard or i flash it on the laptop with motherboard on by only removing the battery from the motherboard
Depends if you can get at the chip when you take the bottom off, if no gotta take it out. Either way disconnect battery and power.
Mpeg2 Rom file dawnload
Tomahawk B450 bricked when I did "instant flash". Ordered the programmer and clip and this video is very informative thank you. Here's hoping it'll save my board.
can u update the situation ?
how did it go?
Thank you, I just bought the programmer to try writing a correct bios to a fake 1060 6GB gpu I bought off ebay and I was wondering how that would work. Hope I find a bios that makes the card being properly detected afterwards.
You should make a video of you doing this with a raspberry pi if you have one. The CH341A isn't even needed if you have a Pi and the test clip. Just have to find a way to connect the test clip to the Pi's GPIO port/header or get just a clip with some female to female jumper cables/wires to connect from the clip the Pi.
Flashrom have problem if u have 4mb chip and 236kb file its can't write but in window its write and work i test it...in flashrom if u do its give u error file size didn't match to chip size i don't know why and the developers didn't fix it ..fow window asprogrammer write and work fine
Can you recommend a good quality programmer and test clip? I know you are using a CH341A, but the ones I am looking at have some reviews complaining of poor quality and excess voltage. I'm wondering if there's a good manufacturer out there.
Thank you so much for this. You explained everything perfectly. I wish all tutorials were this good.
I have a k5000 graphics card that I want to flash to have Mac boot on it, I bought the 512k chipset since the original is 256k and the file size is slightly bigger. How can I write onto that chip? Also looking at it, it doesnt have a dot in the upper right corner.
I use AS Programmer and Neo Programmer on msi laptop flashing bios but no luck black screen always :/
Hey my dell 7567 got bricked cause of dells stupid dell support automatically downloading and installing the bios on its own. My previous bios was 1.11.0 is it safe to install one of the older bios or will old bios cause issues?
Hi there, what is the difference between 24x and 25x on CH341A programmer? thnx
You're lucky if it works without removing the chip. Often one finds that the other circuitry around the chip make it impossible to provide enough power to the chip and/or enough signal to program it.
nice ! it's working with last gen graphic card ? like rx 6800? she is not detected anymore by atiflash :(
Thanks buddy, need to fix my daughters laptop, this will for sure save me time when the programmer arrives. Thank you.
dude i kinda feel ashamed for still falling for this stuff but i fell for the fake gpu, and this video helped me! thanks a lot
Thank you
I have question
Acer 5745Dg has 2 bios chip kbc spi and pch spi wich one to flash for bios?
I can't use the clamp, the spring is extremly thigh, everytime I put it on the chip it just gets out and it feels and sounds like its breaking the chip.
can i still flash the bios just using the test clip?
If chip fits and you can read the contents, you should be able to write to it as well.
how to determine if its 24 or 25 series?
Look at the number written on the chip package?
@@ras666 Some people get a little slow with age and forget to put on their reading glasses.
woohoo! like # 1000
I cant seem to find the programmer file anywhere, do you know where I could download it for windows?
thank you so much for your work bro,
my programmer doesn't work. It seems that the programmer is faulty. not a single bios chip connects to it. it doesn't read the chip the power light just dims which means that there is a short somewhere. and it doesn't matter which way i put the test clip on it still just thinks that its shorted.
Hi! Great video, I am using the windows version of the program, it's more simple. But after a couple of success, now it's like the clamp doesn't work anymore, when I place it on the bios it always slip me out, it cannot stay firmy on the chip. DO you know why? The plastic is gone? This clamp probably sucks, I don't know if I can find on internet a better clamp. Is it possibile?
in the 90's we just used UV light. lol I still prefer the old method..... but too bad the old method no longer works.
would this be able to unbrick my Red Devil RX 580 8GB?
hi i need help knowing what bios chip my notebook has its very difficult to read and some of the text is worn off isint there a program or data base i can search for my bios chip name and manufacture ?
Excellent video. Appreciate your taking the time to and effort to share this.
Do you know if there are similar deices ot use to read from a USB flash memory chip?
Thanks for sharing this on Win/Linux. Do you think I will be able to re-flash a Asus B450F Gaming MB Bios Chip with this? (I bricked it ;)
Thanks for Reply,
Roger
ty so much man
Can this device be used to strip away a forgotten password on the bios?
im on my 3d bios chip flasher. and none of these read any of my bios chips. would not recomend it.
For other modem models
From what site
Download the firmware file
15:18 "or u can edit it right in memory if ure crazy" hahahaaha XDDD
can i fix a bricked gtx 1070 with this method?
Thank you so much. This is very helpful!
8:13 Linux already loads the CH341a w/o installing a driver? Nice! "flashrom" is the CH341a driver? If I run MXLinux (or Linux Lite) will the repositories be Ubuntu or any Linux? Thanks!
Any standard ubuntu kernel will have it as a module... If you run a stripped down custom kernel, then it may not.
Greetings, interesting resolve being clueless such a fix existed. Considering I've been spending endless hours attempting to normalize my corrupt BIOS that invaded my gravity standing sideways.
I have a dysfunctional Lenovo YOGA 730-15IKB Laptop, question; Are the flasher Test clip Devices universal for all computers or device specific for specific model computers?
Thank you very much for posting this vital educational post for all of us, remain well...
the controller is universal, depending on where you buy ot from it will be ready to flash BIOS for motherboard/GPU just double check on your chip what kind of voltage it needs so you don’t fry your chip. It usually comes setup for 3.3/5V but some chips are 1.8V and you’ll need an adapter for them, look up everything before doing the procedure so you don’t have any problems!
those programmers usually run at 5v. that bios chip and most bios chips run at 1.8v you either need the 1.8v adapter or you'll bake the chip... im assuming.
Shouldn't assume that vin = vout
Clean and clear information so far
In the file for the 341a programmer, there's a bunch of documents. Read the section on modding for 3.3v use as some devices won't program. If you get any verification errors, check all the options under the write drop menu item. Until I did that I kept getting errors.
There is a jumper to select 3.3v or 5v on the board
the clip won’t stay :/
Thanks a lot for this informative video!
hlo bro ,how much will b charged for BIOS flashing?
Reminded me of the NES game lol
Thank you - saving me hours of research
Thanks man! Now Im all set up and ready to flash
Hi deftdawg,,, Have you ever attempted any Chromebook bios's with this outfit? Thanks for informative video
Only machine I tried it on was the Lenovo (windows laptop) shown in the video.
Awesome really good one
I NEED THIS REALLY BAD
Thank u for teaching
Hi can you tell me how the 8 wires go on the test clip
Keep stabbing the board with your screwdriver when pointing and you may knock some surface mount components off, be more delicate!
'twas on a 15 year old video card I pulled out of a old junk bin, not too worried about it. :D
@@deftdawg Your off a year. 14.. and that's if you got it the day it was released... just messing with ya. Good vid.
Very cool!! 😎 👍
Thanks for the sharing. I have 2 questions
1. My bios chip is Mx25L12873, can I replace it by another mx25 bios chip or w25Q?
2. I tried to flash my bios chip using the ch341a and the test clip but after that my laptop don't power on and the charging led is blinking white and orange. Could you please help?
Many thanks to all
Did u fix bro
@@tbskitt Yes I did
@@aliissa8347 how
master laptop
thanks so valuable knowledge!
In linux was a tool you could see and extract the partitions of such an image, do you know what I mean?
binwalk
@@deftdawg Thats it, thanks man!
MUCH BETTER!
thanks bro
Great video! Thanks for the clear explanation!
Awesome! thanks
so where can i download a bios bin? you forgot to put the link
Didn't think anyone would want a bios bin from a card that's more than 15 years old... do you need it? lol
@@deftdawg yes plesae
Hey please do it on Windows I don't understand Linux please
Okay, done... just skip to the second half of the video 😋
@@deftdawg thanks, does this work on a laptop
@@looterin8986 the clamp is far too small to clamp an entire laptop, it's meant for chips.
@@deftdawg I meant a laptop vbios chip
Thank you >>>>
Great video! I will be doing this in a few weeks when my CH341A arrives and this will be very helpful.
Great tutorial, buddy! I've got the same ch341a programmer, I know where to start from, but just wanted to confirm, other hackers have used it successfully. Thanks!
Is this supported with mxi25l6473e? Please help me 😭
Hey mate,
How does this work if the file is .rom type? For Amd RX cards.
They really need a version that just pushes down over the chip. The clips are a total pain in the ass.