Hello, just followed your post.. very much helpfull. I have the intrument cluster changed from the old owner, i was able to change the millage. The issue is that i cannot change the vin on the IKE. Its telling me that i need to factory reset before performing this action. The problem is that the factory reset is greyed out and cannot be click. Do you have any idea about this.
Hello, I would like to know if when we change a meter, we can no longer see the instant consumption, the time or the autonomy and is what it blocks the wheel to set the time. Thank you in advance.
Hi. I have a different case. My LCM is at the correct Odometer reading but my IKE Cluster is not. Can I code it using your method but for the Cluster instead of the LCM?
Hi, i‘m repairing a fire damaged E46 and have been supplied a used LCM, following your instructions to 1st check for correct algorithm in the support list, it only finds a partial algorithm match HC912-12 coloured in red and the part number is different, does this mean i cant match to the car.?
I changed my dash on E46CI and left traction and brake check what can i do? I have this point and i think i must change the VIN like this? Can you reply me what can i do or can you help me any way thanks ❤
Thank you so much for all of your videos! Best on yt for sure! Can you please post video about correct procedure for coolant change and bleeding system on n42/n46 engine? It's different than other e46 engines, and almost all info on the net is about m52/m54 engines. :/
Also would like to know this as well. Have a donor cluster with original LCM. Is software enough, or do we have to unsolder chip inside of cluster then reprogram?
Hi sir I change my cluster out with other one but I have the dot infront the miles and my fuel range, outside temperature etc is not working? Any ideas
To fix the odometer in the cluster you need to desolder the chip from the board and reprogram it (there are people on the internet that do this as a service). Desoldering is a problem if you dont have the skils and tools. Alternative is a hack where you set the speed factor so that the miles increase much faster (for example x100), you then drive the car precisely until you reach the desired miles and then reset the speed factor. This is a tricky hack, but can be done.
@@BimmerZen Hi, I have the same problem as you but in reverse, the previous owner changed the cluster because the crystals were broken, (fortunately the new cluster has the same mileage as the LCM at 1500km ready, I will write again the mileage on the cluster on the LCM) but my question is is it possible to write the VIN of the LCM on the new meter? Rather than the opposite as in the video.
![💻 [PA Soft] BMW Scanner on Windows 10 (Check for Codes and Settings on your BMW)](http://i.ytimg.com/vi/JjNkEYkDFMI/mqdefault.jpg)
![30 ชั่วโมงคนเดียว บนรถไฟชั้น 3 โซเวียต [Around The World Ep. 2]](http://i.ytimg.com/vi/MlE9boAVqDA/mqdefault.jpg)
Single handedly the best instruction video on youtube. Clear, concise, to the point and step-by-step! Thank you.
Work's on my M43..Thanks for sharing! 👍🏾
thanks! it worked! was just a hassle installing the drivers on windows 11. but finally managed to do it and now my tamper dot is gone!
Hello, just followed your post.. very much helpfull.
I have the intrument cluster changed from the old owner, i was able to change the millage.
The issue is that i cannot change the vin on the IKE.
Its telling me that i need to factory reset before performing this action.
The problem is that the factory reset is greyed out and cannot be click.
Do you have any idea about this.
i have the same problem, did u find a solution?
Hello, I would like to know if when we change a meter, we can no longer see the instant consumption, the time or the autonomy and is what it blocks the wheel to set the time. Thank you in advance.
Hi. I have a different case. My LCM is at the correct Odometer reading but my IKE Cluster is not. Can I code it using your method but for the Cluster instead of the LCM?
it will work on all windows , you have to disable driver signing in safe mode after that it will install , hope this helps you .
Hi, i‘m repairing a fire damaged E46 and have been supplied a used LCM, following your instructions to 1st check for correct algorithm in the support list, it only finds a partial algorithm match HC912-12 coloured in red and the part number is different, does this mean i cant match to the car.?
This device is only for bmw e46 ,its work for e60? Can i conectat this device with my car BMW e60?
I changed my dash on E46CI and left traction and brake check what can i do? I have this point and i think i must change the VIN like this? Can you reply me what can i do or can you help me any way thanks ❤
Very helpful thank you
Thank you so much for all of your videos! Best on yt for sure!
Can you please post video about correct procedure for coolant change and bleeding system on n42/n46 engine? It's different than other e46 engines, and almost all info on the net is about m52/m54 engines. :/
Will dot show if difference is like 30km?
@@GiaNebieridze i think it has to be bigger than 100km.
@bimmerzen, the link for the cable does not seem to work/list the part on eBay. Thanks
works normal for me..
Another useful tip, thank you
What if we changed the gauge cluster? Can you do another tutorial? Btw, very useful as always
Also would like to know this as well. Have a donor cluster with original LCM. Is software enough, or do we have to unsolder chip inside of cluster then reprogram?
It will work on BMW E39?
I'm not 100% sure but I think it should be very simmilar.
Hi sir I change my cluster out with other one but I have the dot infront the miles and my fuel range, outside temperature etc is not working? Any ideas
Have you find a solution for your problem ?
A quality content
How to change milage? my old speedometer nroken and bought one from jankiyard but the new one has lower mileage
To fix the odometer in the cluster you need to desolder the chip from the board and reprogram it (there are people on the internet that do this as a service). Desoldering is a problem if you dont have the skils and tools. Alternative is a hack where you set the speed factor so that the miles increase much faster (for example x100), you then drive the car precisely until you reach the desired miles and then reset the speed factor. This is a tricky hack, but can be done.
I need the valve stem seals tool kit removal im from zambia
I can ship to Zambia.
Question real quick is it bad to just leave it and not reprogram it
I have it on my 530d because the last owner change the odometer (crystal dead).
I think it’s not serious
No problem at all.
@@BimmerZen Hi, I have the same problem as you but in reverse, the previous owner changed the cluster because the crystals were broken, (fortunately the new cluster has the same mileage as the LCM at 1500km ready, I will write again the mileage on the cluster on the LCM) but my question is is it possible to write the VIN of the LCM on the new meter? Rather than the opposite as in the video.
So if I have an e46 and wanted to swap the cluster I can and the car will start with no issues?