+Joscha Hasselberg LOL, yeah I had the same problem, I almost gave up, and then a video came on by itself directly after this one and someone mentioned that,,lol
WORKED!!!! Thanks Jason! :) For all who ended up in Failsafe mode for all the toggles. -Mandatory!!! : Reverse the PIT on TX first off other wise you will end up in Failsafe mode for every toggles (N,1,2 and Hold). Will not work if you reverse it on Naza assistance software alone. Good Luck!
Just a note to thank you for this video. I tried another method with the gear switch to get to failsafe but couldn't get it to work in all 3 flight modes. Now I have to figure out a video switch and gimbal tilt and I'm ready. Thanks again.
THANKS! finally a video that showed you are suppose to set the Pit Curve settings all the way down, not just on the first!!! Been stuck on this for a week! Finally I can fly again!! HK told me it was impossible to use Heli mode!!
Hey Chris! Glad to help. The first thing that you need to do before you set the values is enable the throttle cut switch in the settings. You have to make it active. Then, follow the programming guide as I show in the video and you will see that when you flip the throttle cut switch it acts as a failsafe switch instead in the NAZA software. -J
X-Quad, question at any point do we have to click on the write button after we put the values in? you did an awesome job thanks for the help. also how do you like the FSth9 I've good and bad things about it... the price is right that's for sure. thanks again.
Hello Jason Jason thanks for everything, you know only your explanation of flysky 9x configuration naza works, I had tried at least 10 sectors from various videos on You tube but none worked well, not to say that did not work at all. Great great great ...... Thanks Jason
You must select helicopter under model type selection. It does not matter which helicopter model you choose, just do not choose Airplane. You may need to increase or decrease the value by a point or two on the throttle cut to get the failsafe to kick in. It can only be done properly while you are paying attention to the software when you are hooked up. I have set up over 100 of these radios all exactly the same.
Saw you say you setup over 100 of these...can I ask you a question? When I setup the 9x on the quadcopter (naza m lite), it seems to not be giving it enough throttle and will not take off. Sort of like if it was too heavy. Just barely lifting at full throttle. Everything was lined up properly and responding in the assistant software. (Sticks calibrated and flight modes) When I switch back to the old transmitter, it fly's fine and strong. My flight mode switch works fine on the new one too.. It seems like it is something in the transmitter setting doing this because when i switch back to the older radio it works fine.. like something is limiting throttle to be 100% although throttle shows as 100% in the naza stick calibration..What setting do you think it could be on my 9X? Thank you Kindly!!
Brilliant video my friend, this really helped me tons, any more on this system with the naza would be a massive help. Keep up the fantastic vids buddy.
Thank you for sharing the step by step of how to set up the fail safe on the 9X for the NAZA M. I programmed it and on my transmitter it shows the same as yours. I don't have a NAZA board as of now, but might in the near future. What I was looking for when I found your video was how to get the Fail Safe to work on the Turnigy 9X C Rx V:2 with the Turnigy 9X Tx V:2. I saw one video that used it with the stock receiver and just set the throttle to 000% with the stick and saved it in active Fail Safe setting? I have tried several times and this doesn't work for me? Now I'm wondering if there is a way of setting it up similar to what you show here so if Tx signal is lost the throttle will cut. I have seen plenty of videos on how to change modules to FrSky and Orange , but if this is supposed to work I would sure like to figure it out. I just purchased this Tx and Rx combo because I am on a very limited budget and will have to wait at least a month before I can buy any more parts.
Hey D, try this: Remove all of your blades and then start up your motors. Make sure that you are in GPS mode to start this out. After the motors are running, put the quad into attitude mode and then into manual mode. What type of difference do you see in the motors and how fast they go? This is a test to be sure that your manual mode is working properly. when you give your quad some throttle, does your status indicator light for your NAZA stay the same? Does it go into any other mode as you give it throttle? The settings have to be exactly the same as I show in the video for this to work. If you miss even one detail this will not work for you. Let me know what you find D. thanks!
Hi you stated that the turnigy 9x needs to be in helicopter mode for the dji naza flight control. But should it be in Heli 1, Heli 2, Heli 3-1, Heli 3-2 or Heli 4 ? Please help this is my first quad build which is a Hk Predator 650.
Jason sorry I am new at this just watched your Skyfly setup and have a couple of problems hope you can help I have a skyfly TH9 I have set in the transmitter as per your youtube. but what receiver port do I have to use and where in the Naza do I plug into also any other transmitter settings do I need to change. Thanks
Hello Jason, Great video and I'm going to get Naza Lite also w/GPS . I also have Turnigy 9x and just upgraded the receiver to Frsky D8R Plus [telemetry] and my question to you is my frsky will work right? and if Tx lose signal completly [ i,e Tx went west ] and it will return home [ RTH ] automatically, right ? just curious. and I will try to set up for "Home Lock" mode also but abit scare..LOL.
Hi great job but qick question whats happen i your radio is of it will go to fail safe?? . My radio is on delivery so i cant check this my sefl . thanks
I have a question about using the FS Rx with NAZA Lite. What happens when the Tx signal is lost during flight? Can the Tx regain control if the copter is close within range or it will stay in RTH mode and land?
I hate to be awkward but I'd like to use the gear switch to select failsafe and use the throttle cut switch to force the throttle to 50%, can you help me please? the mode switch is set up as you've suggested. Thanks in advance!
Hello jason... I have a problem with the rudder calibration. Its always to the right. And becomes center when i move the switch to 'LEFT'. It never comes to the original left. Any solutions you might have? Thanks alot.
You need to adjust your values slightly while WATCHING the NAZA on screen until they turn blue for each setting. REMEMBER: you must have each value the SAME just like in the video of you change something. Good luck
Plzzz help. I cant use switch mode ( f mode and IOC ) ,just only use pitch trim to control F mode is ok. So how can i use F mode and IOC like you . Thanks
done it exactly as you showed - followed you step by step but still have have solid failsafe on every toggle, any ideas or recommendations, ive got naza m lite. thank you upfront
+simas lukosevicius .... The values provided are close. While connected to DJI Assistant, you need to adjust each value to ensure that it is in its respective position i.e. N = GPS; ID1 = ATTI; ID2 = Manual. I had to change the values to the following N/GPS = 8.5; ID1/ATTI = 43; ID2/Manual = 77.5.
+Domine Pepinillo - I found your comment made me second guess his instructions. However they worked perfectly as long as you follow every step. I used his exact values!
+raphlovesit ... The instructions are very good. They will not work exactly for everyone. I factory reset my 9x transmitter. Followed the instructions. In DJI Assistant, GPS mode switched back and forth between GPS and Failsafe; ATTI mode was Failsafe; same for Manual. I had to adjust each setting (GPS = 8.5; ATTI = 43; Manual = 77.5). These values are not the same as those in the video
I realized this vid is prerty old, but hopefully someone here can help. I have the same setup, but my naza won't go into failsafe when the TX is turned off. Anyone have any ideas on how to fix this? Thank you.
Hallo im novice at this i followed your guide, thanks, but i have an issue with the LED on the Naza i can't star the engines at all.... Led after a few seconds flashes red Fastly!! And I'm given this message in the Assistant software: Configuration error, this may cause by firmware upgrade from old version.or abnormal Tx calibration. Re-calibrate your transmitter,and power cycle your controller and check all of the parameters. I can't fix it I'm almost have given up! Does anyone know whats my problem?? Im stuck ......please help....
question to you, or anybody. set it up exactly like the video same transmitter Naza v2. My problem is the throttle on my transmitter moves the rudder on Naza assistant, and the rudder on my transmitter moves the throttle on naza assistant. its like they're reversed. my transmitter is a Mode 2 (throttle and rudder on the left) receiver is connected as follows... ch1> A. ch2> E. ch3> T ch4> R. any help from anybody would be greatly appreciated
+Marc Cardenas Connectors Naza MC => FlySky FS-R9B A => CH1 E => CH2 T => CH3 R => CH4 U => CH6 X1 => CH8* X2 => CH7* Stick Mode on Turnigy TGY9X is MODE4 (1,3) (4,2) That are my working settings. AUX-CH *CH7, HOV PIT *CH8, PIT TRIM For Gimbal
OK It's a given that I am a complete novice in the sport and just learning everything. But I have watched your video 20 times and checked my settings 15 times and I still can't get it right. the stick movements are Ok but the toggle switch will not change the setting off failsafe mode. I'm using a Turnigy 9X and a NAZA lite, could there be some differences in the transmitters? It's probably something I did wrong but I just can't seem to find it. Any suggestions.
+Chris Michael ... As with Ray, I had to tweak the N, ID1, ID2 values. Connect to DJI Assistant software and tweak the values on the transmitter. With the tweaks, the instructions in this video worked great.
Hey i am facing a problem, i also upgraded my flysky 9x with frsky djt module and v8fr receiver but i am facing a problem when i turn the power on my naza goes to failsafe always even when the trigger button is off. anybody knows anything?... i did binding again but still no luck stock 1 was programmed by your method and is working just fine
+Action Reaction Sorry for the invasion... But i saw your comments in two different websites about d8r and stuck in failsafe like it happends with me right now... Did you find solution? Im trying change the values of pitch curves from other video and looks like its better now. But im afraid that change that values make me crash my first drone XD
How to set E point (pit values showed on this vídeo at 4 min 20 sec) if i got: N - ATT Mode Id1- Manual mode Id2- GPS mode And someone tell why need to change that values to 120% please, so i undrstand what Im doing. Thank you in advance
+Bernard Alamargot ... turn off transmitter. Press and hold EXIT button at same time turn on transmitter. Wait for steady tone. Release EXIT button. Transmitter will reset.
Plzzz help. I cant use switch mode ( f mode and IOC ) ,just only use pitch trim to control F mode is ok. So how can i use F mode and IOC like you . Thanks
8 years after publishing your video you just saved me with my 9x configuration that was working anymore ... many thanks !
Thanks a lot mate! Works like a charm.
The only thing not mentioned in the video: I had to connect U to channel 6. Thanks to Jordan Flagstad!
+Joscha Hasselberg LOL, yeah I had the same problem, I almost gave up, and then a video came on by itself directly after this one and someone mentioned that,,lol
WORKED!!!! Thanks Jason! :)
For all who ended up in Failsafe mode for all the toggles.
-Mandatory!!! : Reverse the PIT on TX first off other wise you will end up in Failsafe mode for every toggles (N,1,2 and Hold). Will not work if you reverse it on Naza assistance software alone.
Good Luck!
Just a note to thank you for this video. I tried another method with the gear switch to get to failsafe but couldn't get it to work in all 3 flight modes. Now I have to figure out a video switch and gimbal tilt and I'm ready. Thanks again.
THANKS! finally a video that showed you are suppose to set the Pit Curve settings all the way down, not just on the first!!! Been stuck on this for a week! Finally I can fly again!! HK told me it was impossible to use Heli mode!!
Thank you for your clear tutorial, I was struggling to set fail safe alone ! :)
Hey Chris! Glad to help. The first thing that you need to do before you set the values is enable the throttle cut switch in the settings. You have to make it active. Then, follow the programming guide as I show in the video and you will see that when you flip the throttle cut switch it acts as a failsafe switch instead in the NAZA software.
-J
X-Quad, question at any point do we have to click on the write button after we put the values in? you did an awesome job thanks for the help. also how do you like the FSth9 I've good and bad things about it... the price is right that's for sure. thanks again.
Hello Jason
Jason thanks for everything, you know only your explanation of flysky 9x configuration naza works, I had tried at least 10 sectors from various videos on You tube but none worked well, not to say that did not work at all.
Great great great ...... Thanks Jason
Great Video, Many thanks this has answered several problems I have had.
Followed it to a T and it worked great. I used channel 6 on my RX. Thanks!
Thank you for this video ! It's not so easy for a beginner with only the user manual of the Skyfly TH9X
Great explanation. Worked perfectly. Much appreciated.
Great video, I've been wondering witch transmitter to buy and you just made up my mind. Thanks for the help
Hey Thanks Jason your explanations are awesome and easy to understand I appreciate the time you took to do this.
Very good and helpful video! Thanks.
The settings should be similar, although the software layout of the remote may be slightly different. You could definitely give it a try!
finally someone known what hi talk about... thanks mate
You must select helicopter under model type selection. It does not matter which helicopter model you choose, just do not choose Airplane. You may need to increase or decrease the value by a point or two on the throttle cut to get the failsafe to kick in. It can only be done properly while you are paying attention to the software when you are hooked up. I have set up over 100 of these radios all exactly the same.
Saw you say you setup over 100 of these...can I ask you a question? When I setup the 9x on the quadcopter (naza m lite), it seems to not be giving it enough throttle and will not take off. Sort of like if it was too heavy. Just barely lifting at full throttle. Everything was lined up properly and responding in the assistant software. (Sticks calibrated and flight modes) When I switch back to the old transmitter, it fly's fine and strong. My flight mode switch works fine on the new one too.. It seems like it is something in the transmitter setting doing this because when i switch back to the older radio it works fine.. like something is limiting throttle to be 100% although throttle shows as 100% in the naza stick calibration..What setting do you think it could be on my 9X? Thank you Kindly!!
Thank you so much. I am so happy I found this video. :)
I believe it will RTH after a few seconds. On the ground testing, tuning off the radio will trigger fast blinking yellow.
Brilliant video my friend, this really helped me tons, any more on this system with the naza would be a massive help.
Keep up the fantastic vids buddy.
thanks for this. Got my 3 position working now on my naze32 board. Would not have worked this out by mistake.
Fantastic, exactly what I needed. Thank you!
Thank the turnigy 9x works perfectly
Great video, very well explained. That saved me a lot of time :)
excelente video amigo Gracias el failsafe no sabía cómo programarlo
Thank you so much for this video! Help me a lot.
nice and simple! Thank you ! :)
Thank you for sharing the step by step of how to set up the fail safe on the 9X for the NAZA M. I programmed it and on my transmitter it shows the same as yours. I don't have a NAZA board as of now, but might in the near future. What I was looking for when I found your video was how to get the Fail Safe to work on the Turnigy 9X C Rx V:2 with the Turnigy 9X Tx V:2. I saw one video that used it with the stock receiver and just set the throttle to 000% with the stick and saved it in active Fail Safe setting? I have tried several times and this doesn't work for me? Now I'm wondering if there is a way of setting it up similar to what you show here so if Tx signal is lost the throttle will cut. I have seen plenty of videos on how to change modules to FrSky and Orange , but if this is supposed to work I would sure like to figure it out. I just purchased this Tx and Rx combo because I am on a very limited budget and will have to wait at least a month before I can buy any more parts.
great video
Great wideo ! thanks ;)
Follow the video instructions from the very beginning to the end and it will work for you I promise.
excellent video. well done mate👍
Hey D, try this:
Remove all of your blades and then start up your motors. Make sure that you are in GPS mode to start this out. After the motors are running, put the quad into attitude mode and then into manual mode. What type of difference do you see in the motors and how fast they go? This is a test to be sure that your manual mode is working properly. when you give your quad some throttle, does your status indicator light for your NAZA stay the same? Does it go into any other mode as you give it throttle? The settings have to be exactly the same as I show in the video for this to work. If you miss even one detail this will not work for you. Let me know what you find D. thanks!
Thank u so much sir..
thank you for sharing this...
Great!! well explained video. Can you please also share settings for RTH with RX in switched off mode.
Hi you stated that the turnigy 9x needs to be in helicopter mode for the dji naza flight control. But should it be in Heli 1, Heli 2, Heli 3-1, Heli 3-2 or Heli 4 ? Please help this is my first quad build which is a Hk Predator 650.
Jason sorry I am new at this just watched your Skyfly setup and have a couple of problems hope you can help I have a skyfly TH9 I have set in the transmitter as per your youtube. but what receiver port do I have to use and where in the Naza do I plug into also any other transmitter settings do I need to change.
Thanks
Hello Jason, Great video and I'm going to get Naza Lite also w/GPS . I also have Turnigy 9x and just upgraded the receiver to Frsky D8R Plus [telemetry] and my question to you is my frsky will work right? and if Tx lose signal completly [ i,e Tx went west ] and it will return home [ RTH ] automatically, right ? just curious. and I will try to set up for "Home Lock" mode also but abit scare..LOL.
Hi great job but qick question whats happen i your radio is of it will go to fail safe?? . My radio is on delivery so i cant check this my sefl . thanks
thank you sir!
I have a question about using the FS Rx with NAZA Lite.
What happens when the Tx signal is lost during flight?
Can the Tx regain control if the copter is close within range or it will stay in RTH mode and land?
I hate to be awkward but I'd like to use the gear switch to select failsafe and use the throttle cut switch to force the throttle to 50%, can you help me please? the mode switch is set up as you've suggested.
Thanks in advance!
I have a naza m v2 and I connected it via the ppm port would that change it from tradition to ppm?
excellent vid thx
I have to ask, how did you come to learn this, its very difficult to figure this out without someones help, just curious
Why does my throttle also control the Flight mode? I have U as Channel 6. I can't work out why this happens. Also what is your AUX Chan setup??
Hello jason...
I have a problem with the rudder calibration. Its always to the right. And becomes center when i move the switch to 'LEFT'. It never comes to the original left. Any solutions you might have?
Thanks alot.
You need to adjust your values slightly while WATCHING the NAZA on screen until they turn blue for each setting. REMEMBER: you must have each value the SAME just like in the video of you change something. Good luck
hi. i followed it but in the NAZA assistant, the control mode switch won't go blue. Thanks
Plzzz help. I cant use switch mode ( f mode and IOC ) ,just only use pitch trim to control F mode is ok. So how can i use F mode and IOC like you . Thanks
done it exactly as you showed - followed you step by step but still have have solid failsafe on every toggle, any ideas or recommendations, ive got naza m lite.
thank you upfront
+simas lukosevicius .... The values provided are close. While connected to DJI Assistant, you need to adjust each value to ensure that it is in its respective position i.e. N = GPS; ID1 = ATTI; ID2 = Manual. I had to change the values to the following N/GPS = 8.5; ID1/ATTI = 43; ID2/Manual = 77.5.
+Domine Pepinillo - I found your comment made me second guess his instructions. However they worked perfectly as long as you follow every step. I used his exact values!
+raphlovesit ... The instructions are very good. They will not work exactly for everyone. I factory reset my 9x transmitter. Followed the instructions. In DJI Assistant, GPS mode switched back and forth between GPS and Failsafe; ATTI mode was Failsafe; same for Manual. I had to adjust each setting (GPS = 8.5; ATTI = 43; Manual = 77.5). These values are not the same as those in the video
Can you please do a NAZA set up with the Flysky FS-i10 please it's the up grade to this transmitter thank you :)
thanks man. Have you confirmed that failsafe works? tons of stuff on forums saying 9x failsafe will not work. I have the HobbyKing Turnigy 9x v2.
I realized this vid is prerty old, but hopefully someone here can help. I have the same setup, but my naza won't go into failsafe when the TX is turned off. Anyone have any ideas on how to fix this? Thank you.
Hallo im novice at this i followed your guide, thanks, but i have an issue with the LED on the Naza i can't star the engines at all....
Led after a few seconds flashes red Fastly!!
And I'm given this message in the Assistant software:
Configuration error, this may cause by firmware upgrade from old version.or abnormal Tx calibration. Re-calibrate your transmitter,and power cycle your controller and check all of the parameters.
I can't fix it I'm almost have given up!
Does anyone know whats my problem??
Im stuck ......please help....
question to you, or anybody. set it up exactly like the video same transmitter Naza v2. My problem is the throttle on my transmitter moves the rudder on Naza assistant, and the rudder on my transmitter moves the throttle on naza assistant. its like they're reversed. my transmitter is a Mode 2 (throttle and rudder on the left) receiver is connected as follows...
ch1> A. ch2> E. ch3> T ch4> R.
any help from anybody would be greatly appreciated
+Marc Cardenas Connectors Naza MC => FlySky FS-R9B
A => CH1
E => CH2
T => CH3
R => CH4
U => CH6
X1 => CH8*
X2 => CH7*
Stick Mode on Turnigy TGY9X is MODE4 (1,3) (4,2)
That are my working settings.
AUX-CH
*CH7, HOV PIT
*CH8, PIT TRIM
For Gimbal
Can this be done for aircraft for use of flaps too, if so how?
OK It's a given that I am a complete novice in the sport and just learning everything. But I have watched your video 20 times and checked my settings 15 times and I still can't get it right. the stick movements are Ok but the toggle switch will not change the setting off failsafe mode. I'm using a Turnigy 9X and a NAZA lite, could there be some differences in the transmitters? It's probably something I did wrong but I just can't seem to find it. Any suggestions.
Chris Michael Same with me. I read the one of the other posts below about tweaking the values while watching the Naza screen.
Worked like a charm!!!
+Chris Michael ... As with Ray, I had to tweak the N, ID1, ID2 values. Connect to DJI Assistant software and tweak the values on the transmitter. With the tweaks, the instructions in this video worked great.
Hey i am facing a problem, i also upgraded my flysky 9x with frsky djt module and v8fr receiver but i am facing a problem when i turn the power on my naza goes to failsafe always even when the trigger button is off. anybody knows anything?... i did binding again but still no luck
stock 1 was programmed by your method and is working just fine
+Action Reaction Sorry for the invasion... But i saw your comments in two different websites about d8r and stuck in failsafe like it happends with me right now... Did you find solution? Im trying change the values of pitch curves from other video and looks like its better now. But im afraid that change that values make me crash my first drone XD
Anyone know how I set up my Turnigy 9X for a Naza-H...no GPS.
what u flying
How to set E point (pit values showed on this vídeo at 4 min 20 sec) if i got:
N - ATT Mode
Id1- Manual mode
Id2- GPS mode
And someone tell why need to change that values to 120% please, so i undrstand what Im doing.
Thank you in advance
+Manel Correia ... flip the control mode switch to allow you to change both values to 120
what helicopter mode? 1 2 3 4?
Hi, I use this radio with a boat, some one now how can I full reset it? Thank you.
+Bernard Alamargot ... turn off transmitter. Press and hold EXIT button at same time turn on transmitter. Wait for steady tone. Release EXIT button. Transmitter will reset.
+Domine Pepinillo Thankyou for your answer , I try it this week.
Heli 1
Plzzz help. I cant use switch mode ( f mode and IOC ) ,just only use pitch trim to control F mode is ok. So how can i use F mode and IOC like you . Thanks