1999-2003 7.3L Powerstroke Transmission Cooler Installation Guide by Mishimoto
ฝัง
- เผยแพร่เมื่อ 18 เม.ย. 2018
- 1999-2003 7.3L Power-stroke Transmission Cooler
www.mishimoto.com/ford-7-3l-p...
Engineering: engineering.mishimoto.com/?
Facebook: www.mishimoto.com/facebook-red...
Twitter: www.mishimoto.com/twitter-redi...
Instagram: www.mishimoto.com/instagram-re...
MODEL: MMTC-F2D-99SL
•Direct fit for the 1999-2003 Ford 7.3L Powerstroke
•Proven +10°F (+5.6°C) drop in transmission fluid temperature with no additional fluid pressure drop
•No modification necessary for installation, functions with all stock equipment
•37-row stacked plate fluid cooler provides larger surface area over the stock 9-row transmission cooler
•Transmission cooler core has a 265% increase in core volume compared to the factory 9-row transmission cooler
•Increases transmission fluid capacity by 1.0 qt
•Mishimoto Lifetime Warranty
Disclaimer
• Please dispose of any liquids properly.
• Allow vehicle to cool completely prior to attempting installation.
• Mishimoto Performance (MP) is not responsible for any vehicle
damage or personal injury due to installation errors, misuse,
or removal of MP products.
• MP always suggests that a trained professional install all
MP products.
• Do not run the engine or drive the vehicle while overheating.
Serious damage may occur.
• Raise vehicle only on jack stands or on a vehicle lift. - ยานยนต์และพาหนะ
Installed one of these on my 7.3 excursion pulling my boat from sc to the keys in July highest my trans temps reached was 155
how do you bleed the trans line going to the cooler to help with oil leaking when line is removed? Or, is it easier just to let the little bit drain out?
If you are careful you will have minimal oil drain from the line you disconnect. you can then try and remove the cooler with the fluid still inside.
Has anyone bypassed the radiator feed lines and just tied into the two lines in the frame ! If so what were your results? Some are saying the transmission run a bit cooler.
Is this a bigger cooler than the one made for the 6.0?
This cooler is an upgrade to the 6.0, although the video is intended for the 7.3 the cooler itself is the same. The 6.0 will not come with lines as they are not needed.
Just ordered mine. Using my 7.3 excursion to tow anything gets my transmission temps dangerously high. I find it remarkable that just an extra quart of transmission fluid would make such a difference. Should I do a transmission flush before or after I install the new cooler?
Wouldn't be a bad idea!
please help so on my 2003 f250 i need transmission lines and i found my two transmission lines do they connect to my transmission cooler as showen in the video because i cant see the transmission cooler infront of the grill or is it hidden because i got told the radiator is the transmission cooler is that true or false thanks
Shoot us an email at support@mishimoto.com and the team would be happy to help out. Thanks!
I’ve contacted you guys thanks !
how many quarts does trans cooler hold
The cooler and lines will hold roughly 1.5 QT of transmission fluid. This is a 1 qt increase over the OEM unit.
Will this cooler fit on a 2001 ford f350 v10 since it's got the 4r100 transmission
We have not tested this on the V10 models. Sorry!
A lot of people have put these on their V10 super duties and Excursions and say they're a huge upgrade. I just bolted mine in and everything fits. (2001 V10 Excursion)
Can this be made to fit the obs trucks with e4od transmission?????
This is not something we have tried and modifications to the vehicle or product may be needed for fitment.
@mishimoto anything is possible, I know. I was thinking of doing the 6.0 liter upgrade, but your oil cooler sounds even better
so much easier jist to pull the bumper
You don’t even need to pull the bumper, pulling the grille is way easier
Will this work on obs 7.3
We have not tested this on the OBS 7.3L. Sorry!
drivers side hose goes to which line
Our transmission cooler is bi-directional so you can install those lines either way safely.
ok thanks , also i just purchased one of your trans coolers off of ebay for the 7.3 , i think i have the wrong hoses the ebay seller stated that the curved hoses for the 7.3 setup have been discontinued by the manufacturer is this true or has the seller sent me the wrong set up , Thank you
The molded hoses are no longer being developed. The process of molding the curve caused some issues with pressure stability and we burst a few during testing. This prompted a change over to straight hoses with some additional length for slack.
ok thanks
@@mishimoto even the curved hoses with the armed type mesh ?
Does this cooler bolt on to the header panel or where
This bolts to the structural support where the OEM cooler is currently installed.
Can it fit f250 V10 2003 6.8L gas engine?
We have not tested this in the V10 gas engines. Sorry!
There's a guy that has a channel about the 7.3 power strokes that did this exact thing for one of the tool dealers vehicles.
My 7.3 cooler didn’t come with lines!!!!
Feel free to shoot our team an email at support@mishimoto.com and we should be able to take care of this for you
why did the mishi cooler look extra fucked on install?
Hey Mike, we used our prototype model during filming and pulled it off the truck a few times. We apologize for any dings and dents that may be showing in the video.
Sorry to say that while may be an outstanding product, the video’s instructions don’t correspond in several key areas to the architecture of at least a 2000 Excursion. Extra shrouding in different locations, less-accessible upper cooler mounts...only use this video as a rough guide!
Jason, putting mine on a 2000 excursion. Any tricks you could forward would be greatly appreciated.
Same for my 2000 f250 bud
My 2001 Excursion worked great although I did remove the front grill and that helped me to access the upper 2 bolts, particularly on re-install. I also trimmed a supplied hose. I thought the instructions and video were very helpful.
you want them to make a video for every possible truck option? would you like them to do one for every color of truck so that you don't get confused? You realize that this video is free right?
@@philodox7599 No, but I would like them to address differences in models that comprise three years (the 7.3 was available in the Excursion from 2000 until 2002-ish) of a four-year date range.
The video isn’t just free...it’s free advertising for Mishimoto. So it’s not like the company is doing potential or actual buyers a favor...
Incidentally, I’m plenty happy with the product, just less-so with their instructions. You’d think the company would welcome the constructive feedback without the need for White Knights wielding snark-swords such as yourself.
Have a good day, tho!