👉 This Video Covers 👈 2:03 :- Motors Issues 5:58 :- ESC Calibration Issues 7:16 :- Moving One Side Problem 8:58 :- Flip Issues 11:37 :- Need 3D Fix 13:06 :- Error While Loading Firmware 14:29 :- Arming Problems 15:48 :- Bad AHRS 16:17 :- GPS HDOP 16:52 :- General Info & Instructions
Hi nice explanation with clear solution. I'm using pixhawk 2.4.8. i can see the copter is arming however it is immediately disarming after few seconds. It's not lifting too. What could be the problem. I don't see the problem in screen.
thanks for todays vedio...I'm making a quad with BLHeli ESC, pixhawk, Dji 2212/920Kv BLDC, radiolink AT9S...Bt when I increase speed after arming & start to increase the speed; the increasing of speed is not smooth means speed increases suddenly with the increment of throttle..Is it a problem?
If your flying in Loiter, position hold mode, Athold mode then after crossing 50% throttle speed of motors will increase suddenly. It's normal. In stable mode speed will increase according to throttle 👍
Bad comapas k liye aap ye batai flight controller konsa use kar rahey ho agar apm 2.5...6 hai to you have to connect voltage regulator by mistake ur board is corrupt so you have to use use alternative connect ion
ASC calibrated all motor spin good but when i set the propeller then motor try to spin but not spin , can you help me about that . apm 2.8 flight controller
Pixhawk flight controller me power module alag lagane ka koi jarurat hai? Job hum ESC or Receiver connect korte hai to positive & negetive connection to mil rahi hai to power module ka jarurat kya? Am I right?
Hi I recently purchased pixhawk 2.4.8 and a hexa frame S550. I am facing some problem with it. Please help me 1. Main out 3 of pixhawk seems to be the problem. Whatever ESC I connect I am not able to spin motor. But with other Main out's I am able to spin. What could be the problem here? How do I resolve? I had flashed Hexa firmware, Octo firmware and quad firmware. None of these firmware worked for me on main out 3 . But main out 3 was working fine before. 2. As I am not able to use main out 3, I had to flash octo firmware for the pixhawk on my hexa frame. So , I could use main out 7 and able to spin the motor. Now I am able to arm the drone. But when I try fly , it leans or drifts towards left side. I am not able to control it and I have damaged my hexa frame. I am using FSi6 transmitter. Do I have to trim? or Do I have to calibrate comapsss. How do I handle levelling issue? Please help me.
In standard parameters search " frame type " you'll seee the frame types there. Sellect Octa and click on " Save parameters " After that do the ESC calibration properly. And make sure your Compass calibration and Acc calibration should be Done property. Every components should be placed in right manner. If you have any questions you con ask me at Instagram
Sir my quadcopter with apm motors are not responding according to throttle increment suppose when I am in ease the throttle full the motors seems to rotate at full speed but when I lower the throttle the motors rotating at full speed only after 2-4 sec the motors are decreasing their rotating speed sir plz solve my problem..
@@OmHobby bro I know but O itna stable nehi that isliye f 450 frame use karke banao Aapne Jo frame banaya wooden ka dji v2 ke levelekliye perfect nahitha So bro please
👉 This Video Covers 👈
2:03 :- Motors Issues
5:58 :- ESC Calibration Issues
7:16 :- Moving One Side Problem
8:58 :- Flip Issues
11:37 :- Need 3D Fix
13:06 :- Error While Loading Firmware
14:29 :- Arming Problems
15:48 :- Bad AHRS
16:17 :- GPS HDOP
16:52 :- General Info & Instructions
Tq bhai. Mere drone ki One side moving problem solved ho gai aapki video ki wajha de. Tq bhai🙏👍
Sir which is the best brand of motor for quadcopter. 1.dji 2,racer star, 3 ready to sky
1st :- Dji
2nd :- Ready to Sky
3rd :- Racerstar
@@OmHobby Thanks
@@mehmoodkhan275 I think you must go with racer star because it gives instant and more thrust than other two motor.
Sunny sky is best
@@RanbotRobotics he didn't mention it and sunny sky motors are heavier than other motors
Hi nice explanation with clear solution. I'm using pixhawk 2.4.8. i can see the copter is arming however it is immediately disarming after few seconds. It's not lifting too. What could be the problem. I don't see the problem in screen.
thanks for todays vedio...I'm making a quad with BLHeli ESC, pixhawk, Dji 2212/920Kv BLDC, radiolink AT9S...Bt when I increase speed after arming & start to increase the speed; the increasing of speed is not smooth means speed increases suddenly with the increment of throttle..Is it a problem?
If your flying in Loiter, position hold mode, Athold mode then after crossing 50% throttle speed of motors will increase suddenly. It's normal. In stable mode speed will increase according to throttle 👍
Bro i have made a tricoptet with apm and now i want to make quad plz tell how to install new firmware
Bro make a video on how to fix bad compass health
Bad comapas k liye aap ye batai flight controller konsa use kar rahey ho agar apm 2.5...6 hai to you have to connect voltage regulator by mistake ur board is corrupt so you have to use use alternative connect ion
ASC calibrated all motor spin good but when i set the propeller then motor try to spin but not spin , can you help me about that . apm 2.8 flight controller
Pixhawk flight controller me power module alag lagane ka koi jarurat hai? Job hum ESC or Receiver connect korte hai to positive & negetive connection to mil rahi hai to power module ka jarurat kya? Am I right?
If you do not connect power module, flight controller will say battery low, and it will not be able to arm
Aap mahan ho bhai 😘
Aaare nahi nahi 😇😇🙏
In dji v2 how can we understand how many satellites are connected
And what is the maximum capacity to connect the satellite
Bro please
Hi
I recently purchased pixhawk 2.4.8 and a hexa frame S550. I am facing some problem with it. Please help me
1. Main out 3 of pixhawk seems to be the problem. Whatever ESC I connect I am not able to spin motor. But with other Main out's I am able to spin. What could be the problem here? How do I resolve? I had flashed Hexa firmware, Octo firmware and quad firmware. None of these firmware worked for me on main out 3 . But main out 3 was working fine before.
2. As I am not able to use main out 3, I had to flash octo firmware for the pixhawk on my hexa frame. So , I could use main out 7 and able to spin the motor. Now I am able to arm the drone. But when I try fly , it leans or drifts towards left side. I am not able to control it and I have damaged my hexa frame. I am using FSi6 transmitter. Do I have to trim? or Do I have to calibrate comapsss. How do I handle levelling issue? Please help me.
In standard parameters search " frame type " you'll seee the frame types there. Sellect Octa and click on " Save parameters "
After that do the ESC calibration properly. And make sure your Compass calibration and Acc calibration should be Done property.
Every components should be placed in right manner.
If you have any questions you con ask me at Instagram
@@OmHobby Thank you very much for you reply and help. I could finally fly the drone smoothly
Useful video bhaiya
Thank you 😊
Apki company dronticluter kaha hai
Big size Drone banane ke liye kitne kharcha Ho Jaaye lag Jaega bhai
VIDEO already uploaded he bro please watch video
Bhai Main To dekh liya Ho like bhi kar diya download bhi kar liya lekin please mujhe bata do SE bar ka drawing banane ke liye Kitna kharcha pad
Please hi bata do na please please
Bhiya I couldn't able to connect my pixhawk to mission planner software,it is showing, no mavlink devise is connected
Please help me
Sir mera pixhawk main teletry nahi a raha hain aur jo dusra telemetry port main a raha hain par pura nahin. Sir help Karo sir...
Bro please reply....🙏
How to know drone battery percentage from ground...pls help me...
Op om bhai
thank you
Pixhawk flight controller mai 2gps laga sakte hai
Off course
@@OmHobby but kaise
Hefull video 👍
Bro..mera radio callibrate nahi ho raha hai mission planner mai..pixhawk 2.4.8 use kar raha hun.. please help
Website kaha gai
I sell 6397090270
Sir my quadcopter with apm motors are not responding according to throttle increment suppose when I am in ease the throttle full the motors seems to rotate at full speed but when I lower the throttle the motors rotating at full speed only after 2-4 sec the motors are decreasing their rotating speed sir plz solve my problem..
Kya black button wala Kk 2.1.5 fly control board real h ya red wala butto
Please help me oreganal Kk bord kon sa h black buttons wala ya red button wala my confused solve me
Black
@@OmHobby Dji Naja m lite control bord aap ki websites se perches karna h kaise ho ga
Thank you sir my problem is fliping
Sir rediolink AT10 kaha se kharide 🙏🙏🙏🙏 please sir🙏🙏🙏
Bhai ek Aisa drone banao Jo jameen per bhi chal sake aur hawa mein bhi ud sake aur camera bhi Laga
Bhai mera apm2.8 drone left side se jada uppar uthh raha hai. Keya karu bhai plzz help me😭🙏
Thanks per Mera drone Landing ke time flip kar raha hai kaya karu??. Flight Controller - - pixhawk. Please
Bro send me video on my Instagram let me seee.
Bro facing 1500+- issue on mission planner using apm
hi all,
i am facing a problem pulsing green light Disarmed )( in pixhawk 2.4.8 how to fit into solid green light(solid green light).
Are yaar maza sagala barobar aahey khar mala arm kasa karaycha te samjena
Droni culture
Bhai mera drone nahi chalra mere pass fs-i5x transmitter hai pls help bhai urgent
Please make a video solve the flip essue
Bad compass health any solution bro
Go to mp settings and set 1 value in compass
bhi please jiyi K3a pro ki pragramming ka vedio please 🙏🙏🙏🙏🙏🙏🙏
Sure
12मोटर 12 esc pixhawk को यक भिडिव बनाउन पडेका
Bhai ek problem ho rhi hai yr ek help kar di bhai jaan
In my drone it's showing error pre arm check mag feild
Anyone have solution plz plz 🙏🙏🙏🙏🙏🙏🙏🙏tell
Adv settings in mp then set 1 value in gps
Hi
Brother we should on all the channels in transmitter for fail safe
Yes. You can
Bhai please radiolink at9s ka review do pleaseeeeeeeeeeee 😭😭😭😭😭😭😭😭😭😭😭
Compass calibration problem help
Bro.. High hdop problem
Agriculture sprayer drone bro
Sure
Thanks bro for ❤️
Ban jayega but it is costly bro.....all motors are very costly
Bro dji v2 se ek aur vedio banao using f 450 frame
Pichla cedio dji v2 utna stable nehitha
Bro please🙏🙏🙏🙏🙏🙏🙏🙏🙏😭😭😭😭😭😭😭😭😢😢😢😢😢
Video is already uploaded bro
@@OmHobby bro I know but
O itna stable nehi that isliye f 450 frame use karke banao
Aapne Jo frame banaya wooden ka dji v2 ke levelekliye perfect nahitha
So bro please
My new pixhwak show -
Check BRD
Mission plner
Check BRD TYPE Failed to i ni t chubeBlack- sensor
Help me please
Lipo battery ka flight backup time kaise nikale
2200 mah 12 minutes 3000 mah 22 minutes 4400 mah 28 minutes.....
Drone aam nahin ho raha
One side problem is not solve
भावा agriculture drone बनव कि plz
Sure bro yeil video