ฝัง
- เผยแพร่เมื่อ 30 ก.ย. 2023
- Easy 6s3p LTO prismatic toshiba scib lithium battery build. 1022 All fab bars
links below
Cells
Repurposed Prismatic LTO With M6 Threading. 2.4V 10Ah 30C continuous 75C peak discharge Lithium Titanate Battery Cell "i personally tested over 11ah "
300amps constant charge and discharge per cell/bank , configured in 6s 14.6v-16.2v recommended charge
Sriko Discount code= BDSB
srikobatteries.com/product/2-...
3p m6 bars
srikobatteries.com/product/lt...
balancer 6s 5a heltec
6S 5A Active Equalizer LTO Battery
Sriko Discount code= BDSB
srikobatteries.com/product/6s... - ยานยนต์และพาหนะ
Heck yeah😊 i just missed your content bro.
Hey whats the best scib cells i see people using the smaller 2.4v 2.9ah cells. What would be the best cells to power a 8000 watt system
Too bad my new refined alt 160a (previously was 90a 14.2v) can only deliver 14.8v max and lowest i noticed was 14.6v (with no audio load) with mid load it crashes down, on 105ah efb battery .. I lov how scib 20ah perform but not sure they will shine with my current alt.. To power a 3.5k rms system , salt-3 with 3 other amps for mids
How much is one of them 30ah sets? What watt's all it work with total? And what's the max charge voltage? I'm looking for a cheap alternative to that headway suoer beast
16.8v max charge
580$ out door with discount
Around 15k constant load
20k burst
@@PunisherOfDeath101 site? Link?
What are you charging at?
@@PunisherOfDeath101$580 my ass
are these the cells in the Xs power Titan 8?
same thing but 1p . this 3p is similar in cost
quick question here, Are this LTO batteries batter or the same in performance in comparaison to an aftermarket LTO for car audio? like the Titan 8 or D4S Litio LTO 6.0 Batteries, Thanks !
These are better quality & speced cells.
These are made in japan . More capable than yinglong
I've been trying to find a good deal on these scibs. which specifically are these scibs? they have a few diff. amp hr ones. did u make ur bus bars? if so what thickness n width are they?
last question, this could do 10k rms, potentially, correct?
Repurposed Prismatic LTO With M6 Threading. 2.4V 10Ah 30C continuous 75C peak discharge Lithium Titanate Battery Cell "i personally tested over 11ah "
300amps constant charge and discharge per cell/bank , configured in 6s 14.6v-16.2v recommended charge
Sriko Discount code= BDSB
srikobatteries.com/product/2-4v-10ah-75c-prismatic-lto-cell-with-m6-threading/?wpam_id=8
we used these bars , and a 6s 5a heltec balancer all from sriko
using discount code BDSB
srikobatteries.com/product/lto-10ah-or-20ah-m6-6s-3p-busbars/?wpam_id=8
@mazda2284 thank u sir. for all the info. I did the math, I should be able to sustain around 10k rms of a 6s,3p bank, charging @14.8v n 320amp alt. 3/0 welding cable. Plz correct me if my calculations are wrong as I wanna make sure my bank is big enough. This 40ah lto bank just ain't cutting it a anymore.
@@troydefond2307 correct 300amps per 10ah plus your alternator . you should be good . i always like to overbuild tho . plannano 24ah banks are also a great option .
@@mazda2284could I buy some cells and go 5s on a stock alt 13.8v and later upgrade to a ho alt 15.5v and rebuild to a 6s battery?
Hey bro can you please clarify for me I just bought the 29AH SCIB bank from NORTHWEST LITHIUM and I have a few people telling me that it doesn't have enough reserves??? If the battery is rated for 15k and I'm not going to be going over 10k total shouldn't it be enough to run the system, LED and the car 4 Cylinder or do I need to get something with the same charging voltage with a lower discharge rate like the ying long style LTO cells and make a battery and if so is there a way to make it resistant to the heat so I can utilize the OEM battery location
It's only about 30 amp hours so you have to consider when you have the vehicle off it's going to drain quickly it is not a ton of Reserve but you can add Reserve also by adding larger capacity cell banks in parallel . Sriko plannano 24ah LTO or 20ah prismatic lto scibs
@@mazda2284 is there a way to possibly put them in a battery delete and insulate the inside and out with a battery heat shield and put it in the OEM location in parallel if so that's what I will do if not what about a bank of say the 30-45AH Ying long or xs power cells in a delete or worst case scenario are the xs power LTO batteries safe for under the hood it says they are but I hear stories of them catching on fire
@@SlamryCamry19 those XS batteries definitely are not under the hood safe as they claim in the fine print you will read that they have a Max temperature of 140 degrees and that they recommend that you isolate the battery from any heat basically the same thing is going to go for any other battery on the market just like the 18 amp our lto that srikobatteries.com has .
@@SlamryCamry19 I actually have a video from slamology last year of somebody's battery that they put under the hood and it started on fire
So how much power could this support on say a mechman 320 with an external adjustable voltage regulator like the ones BrandX sells for $100 that'll adjust from 12.8 up to 15.8 roughly? I've got limitless cyber 12k currently with XS SB1000-31 supercaps and while my voltage is good and strong i definitely would like to charge higher than 14.5...
Are you asking how many amps they can put out? The 10ah cells c rating is 30 constant and 75c burst. So one 6s battery can put out 300amps constantly and 750 amps on a burst. I'm thinking about buying some cells going 5s for my stock alt 13.8 and later getting a ho alt from like js or auto tech internal charging at 15.5v and then rebuilding to 6s.
So how high of a charge could you run this type of bank for car audio, I have a js Alternator 370 amp diodes pushing it to 15.8 but stays around 15-15.5 on average, would this be a possible replacement for the 80ah yinlong bank im running now 😅😅
They say roughly 4k per 10ah
Are you saying 4k watts per 10 ah?@@user-cv6gv4sv2y
@@GTILOUDwould running them in 5s hurt anything ?
Are the studs torque sensitive like yinlongs
Yes, all aluminum stud cells are sensitive. Very few cells have studs that you can just wrench on. I use 6nm as spec to torque. I also use a tiny dab of medium threadlocker from Harbor Freight
@@mazda2284 thank you Brad
Whats a good charging voltage for these scib cells?
It’s in the description
14.8-15.8 is the sweet spot
this is a lifepo4?
LTO
@mazda2284 do these cell have to be compressed
@@bigkato3134 no just contained in a sturdy box from the factory they come in plastic boxes with no compression
@mazda2284 do you recommend cooling fans if they are placed in the cabin of the viechel? Or would tht be unnecessary?
These better than the lev60 148ah batteries?
6s5p with 15 cells is it possible?