Great instructional video. I was a little intimidated on installing my Terrova myself but out of all the videos I watched this one put me most at ease.
Why not connect your new trolling motor power to the underside of the female plug for the old trolling motor? 12v and ground from the battery already there and you don't destroy your old cable.
Good video. I’m definitely no expert but have a suggestion on “puck” placement. I’ve heard and seen that when the Terrova is on the 175, it’s already a little tough to get at the release foot pedal. Just not a bunch of room up there on the 175. You talked about placing the puck on the deck just below the stored motor. It seems that would add to the congestion on the side in which you must stand to get at the release foot pedal. I would probably tuck it in fairly close to your Garmin unit unless that would create interference but it would be out of the way and not get stepped on or kicked. Again, enjoyed the video.
This video was extremely helpful. My terrova just showed up today. I am going to utilize these tips for sure. Thank you! I do have one question. Are there any clearance issues with the bow roller when launching the boat? I notice the terrova sticks out significantly further than the edge.
Getting ready to put one on my alumacraft. Good instruction here👍. Never thought it would be such a pain to swap out trolling motors lol. You got a new sub!
Q - You had indicated that you were going to use your garmin transducer and not the transducer on the TM, because 'you wanted more than just sonar'. What did you mean by that? Surface temp? or is there more than just surface temp you were looking for that the TM transducer will not provide?
I see that the prop sticks out more than the old trolling motor.. do you use a boat cover? And if so doesn't the prop make it a but more difficult to put on?
That's how I decided to install. I didn't want the head unit sticking to far outside the boat. I don't use a cover I keep it in the garage. It seems todo finesofar. I am concerned that it may hitt the dock though.
Check this out on Amazon Canitu 170Pcs Closed Rubber Grommet Assortment,Firewall Solid Closed Hole Plug for Wire Electrical Appliance Plumbing for Auto Car Wire Cable, 7 Different Metric Sizes Assortment Kit www.amazon.com/dp/B07ZNRG42P/ref=cm_sw_r_awdo_navT_g_8D70S42HYX5KBXM6DMY2
Great video sir, I’m about to mount the same set up on my tracker. Thank you!
Thank you and good luck with your install.
Great instructional video. I was a little intimidated on installing my Terrova myself but out of all the videos I watched this one put me most at ease.
Thank you for this video (Terrova)
Did you have to replace the wires?
Why not connect your new trolling motor power to the underside of the female plug for the old trolling motor? 12v and ground from the battery already there and you don't destroy your old cable.
Good video. I’m definitely no expert but have a suggestion on “puck” placement. I’ve heard and seen that when the Terrova is on the 175, it’s already a little tough to get at the release foot pedal. Just not a bunch of room up there on the 175. You talked about placing the puck on the deck just below the stored motor. It seems that would add to the congestion on the side in which you must stand to get at the release foot pedal. I would probably tuck it in fairly close to your Garmin unit unless that would create interference but it would be out of the way and not get stepped on or kicked. Again, enjoyed the video.
Thanks, that helped with my trolling motor replacement!
This video was extremely helpful. My terrova just showed up today. I am going to utilize these tips for sure. Thank you! I do have one question. Are there any clearance issues with the bow roller when launching the boat? I notice the terrova sticks out significantly further than the edge.
No issues. Thanks
Getting ready to put one on my alumacraft. Good instruction here👍. Never thought it would be such a pain to swap out trolling motors lol. You got a new sub!
What length shaft did you get for the terrova?
What length shaft did you get on the Terrova?Thanks
Q - You had indicated that you were going to use your garmin transducer and not the transducer on the TM, because 'you wanted more than just sonar'. What did you mean by that? Surface temp? or is there more than just surface temp you were looking for that the TM transducer will not provide?
Down image as well as side image. The TM paired with the garmin only gives you sonar.
I see that the prop sticks out more than the old trolling motor.. do you use a boat cover? And if so doesn't the prop make it a but more difficult to put on?
That's how I decided to install. I didn't want the head unit sticking to far outside the boat. I don't use a cover I keep it in the garage. It seems todo finesofar. I am concerned that it may hitt the dock though.
@@easttn.fishingdude4169 gotcha.. great job.. good luck..tight lines my friend
Any chance you have a link to the rubber grommets you used?
Check this out on Amazon
Canitu 170Pcs Closed Rubber Grommet Assortment,Firewall Solid Closed Hole Plug for Wire Electrical Appliance Plumbing for Auto Car Wire Cable, 7 Different Metric Sizes Assortment Kit www.amazon.com/dp/B07ZNRG42P/ref=cm_sw_r_awdo_navT_g_8D70S42HYX5KBXM6DMY2
@@easttn.fishingdude4169 Thank you sir!
12v or 24v?
12 volt.
New subscriber
Good video. But you wear uhhh out in it.
Thanks for the feedback. Thanks for watching.