FIXED. PS3 Slim Green Light of Death (GLOD). No video/No audio/No controller sync

แชร์
ฝัง
  • เผยแพร่เมื่อ 2 ม.ค. 2025

ความคิดเห็น • 102

  • @abrahamadekanye5714
    @abrahamadekanye5714 ปีที่แล้ว +4

    Wow great repair job👍 Mr Idrees, i have like four consoles with this exact fault, will chk the bison resistors. Great job
    Greetings from Nathan.

  • @bonk_playz9495
    @bonk_playz9495 17 วันที่ผ่านมา +2

    Hi, my ps3 slim has a similar problem where it turns on but there is no display output. Also the controllers work absolutely fine and are able to sync to the console. There is no video output on both AV and HDMI ports. Please help

    • @idreestech
      @idreestech  17 วันที่ผ่านมา +1

      It’s good to hear your controllers are syncing since that confirms the system is booting. Here's a step-by-step guide to troubleshoot the no-video output issue on both AV and HDMI:
      1. Reset Video Output Settings
      Sometimes the PS3 outputs a resolution your TV/monitor doesn’t support. To reset:
      Turn off the PS3 completely (solid red light).
      Hold down the Power button:
      Keep holding after the 1st beep (Power On).
      Release after the 2nd beep (about 5-10 seconds).
      The PS3 resets its video output to standard definition.
      Connect using both AV and HDMI (to ensure you test both outputs).
      2. Test HDMI/AV Cables and Ports
      Use a working HDMI cable on a known good TV.
      If still no display, test with the AV cable (red, white, yellow wires).
      Ensure ports on the TV and PS3 are not damaged.
      Test another HDMI input on your TV or a different monitor.
      3. Boot into Safe Mode
      Safe Mode can bypass video configuration issues:
      Turn off the PS3 (solid red light).
      Press and hold the Power button:
      1st beep: Power On.
      2nd beep: Power Off (keep holding).
      Release the button after you hear two quick beeps.
      Safe Mode menu should appear.
      If successful, choose Restore Default Settings or Rebuild Database.
      If Safe Mode doesn’t appear, it’s likely a hardware problem.
      4. Check the Hard Drive
      A failing HDD can cause display issues. To test:
      Power off the console and remove the hard drive.
      Turn on the PS3 without the hard drive installed.
      If you see a prompt asking for the storage device, the HDD could be faulty.
      Replace or reformat the hard drive.
      5. Internal Hardware Issue: RSX (Graphics Chip)
      If the above fails, the issue may be with the RSX (GPU):
      Symptoms: System boots, no display output, controllers work.
      Cause: RSX chip’s solder joints may have cracked or weakened over time.
      Possible Fixes:
      Reflow the RSX: Temporarily fixes solder cracks using controlled heat.
      Reballing (Permanent Fix): Replace old solder balls under the RSX with new ones.
      Note: These are advanced repairs. If you’re not confident, consider taking it to a professional.
      Next Steps
      Start with the reset video settings and Safe Mode attempts.
      If no success, test the HDD.
      If still no display, it’s most likely the RSX chip, and a reflow/reballing is needed.
      Let me know how it goes, and I’ll help you further! 👍

    • @bonk_playz9495
      @bonk_playz9495 17 วันที่ผ่านมา +1

      @idreestech Thank you Sir! I'll try out these fixes and update you accordingly

    • @bonk_playz9495
      @bonk_playz9495 17 วันที่ผ่านมา +1

      @@idreestech Hi, I have tried all the above mentioned fixes but none of them work. When I boot it into safe mode there is still no display . However if I boot it into safe mode and try turning the PlayStation off I hear 3 quick beeps. I've also tried removing the HDD but that doesn't not work.
      I've seen a youtube video on how someone fixed a problem similar to this by adding coins between the rsx chip and the heatsink. The uploader stated that this was done to add pressure onto the joints which has loosen because of overheating. Do you recommend trying this?

  • @DarthSimous
    @DarthSimous ปีที่แล้ว +1

    Great repair, Master Idrees ... Another 3000 series Slim saved ...👍

  • @sussysussy513
    @sussysussy513 ปีที่แล้ว +3

    My ps3 slim 3004b turns on for 1 second then off syscon shows error 3010 Do you know ho to fix

    • @abdilnas7563
      @abdilnas7563 ปีที่แล้ว

      That could be a faulty power supply, try to replace it.

  • @lynchdemartini
    @lynchdemartini ปีที่แล้ว +2

    If the resistor is bad will it be too hot to touch when the console is on?

    • @idreestech
      @idreestech  ปีที่แล้ว +1

      I have never experienced like this.

    • @pashamamedov6773
      @pashamamedov6773 ปีที่แล้ว

      Как он узнал среди кучи резистораз, что именно тот неисправен...

  • @bokkibeatz55
    @bokkibeatz55 ปีที่แล้ว +5

    Nice video once again not everyone will be able to fix it because not everybody can afford the oscilloscope try next time with the FT232R USB UART and cool that u use subtitles from now on✌

  • @davedm6345
    @davedm6345 หลายเดือนก่อน +1

    im having some similar but wen i apply pressure on cpu, then when not i power on and the green light going off. what could be?

    • @idreestech
      @idreestech  29 วันที่ผ่านมา +1

      @davedm6345 It sounds like there might be an issue with the CPU's solder joints, possibly cold solder or a loose connection. Applying pressure may temporarily reconnect the joints. A reflow or reballing of the CPU could help resolve the issue. If you're not familiar with these techniques, I recommend seeking assistance from a professional repair technician. Let me know if you need more details!

  • @reshwan_
    @reshwan_ 9 หลายเดือนก่อน +1

    I measured the 500ohm which shows 450ohm and the 55 ones is correct..do i need to change it? I think 450 is okey..so what causing the issue?

    • @idreestech
      @idreestech  9 หลายเดือนก่อน

      Maybe some other component causes it. It could be the GPU as well. HDmi port or its component.

  • @szwnnn
    @szwnnn 5 หลายเดือนก่อน +2

    Me : Are you having a good time Mr. Idrees?
    Him : @4:52

    • @idreestech
      @idreestech  5 หลายเดือนก่อน

      I enjoyed fixing such a mess.😀

  • @AiNolimits14
    @AiNolimits14 หลายเดือนก่อน +1

    Im getting something similar its on but not showing any image no signal and stuck on green light hard drive blink but the ps3 fan takes like a minute to be on 😢

    • @idreestech
      @idreestech  หลายเดือนก่อน +2

      @AiNolimits14 It sounds like the HDMI encoder chip might indeed be the issue if there's no display but the console seems to function otherwise. You can confirm it by swapping it with a new one, the encoder chip for any signs of damage or overheating. If faulty, replacing the encoder chip should resolve the issue. Let me know if you need more guidance!
      th-cam.com/video/w-6pqIoNxaE/w-d-xo.htmlsi=b7CrHmmUdt-SjSXZ

    • @AiNolimits14
      @AiNolimits14 หลายเดือนก่อน +1

      @@idreestech I was thinking of that actually I'll check, ty

    • @AiNolimits14
      @AiNolimits14 หลายเดือนก่อน +1

      @@idreestech then there's another problem the fan started making a big rapid noise like a jet , and it won't let me hold the power button for the second beep

    • @idreestech
      @idreestech  หลายเดือนก่อน +2

      Good luck with your repair!

    • @idreestech
      @idreestech  หลายเดือนก่อน +1

      Try this (th-cam.com/video/1zxNtor_1F8/w-d-xo.htmlsi=oO_va5YXSjBVNCJZ)

  • @t0mbell
    @t0mbell 5 หลายเดือนก่อน +1

    I have ps3 phat cechl with ver-001 board. After start- green light and no image/sound, and no usb voltage. Can i catch errors in this case via uart or i need to manually check board components ?

    • @idreestech
      @idreestech  5 หลายเดือนก่อน

      First get the codes.

    • @lunarhail3559
      @lunarhail3559 5 หลายเดือนก่อน

      @@idreestechdo you have a video of you soldering the wires to get the code?

  • @michaelolayinka441
    @michaelolayinka441 5 หลายเดือนก่อน +1

    I think i have a similar issue, it started as flashing black screens. Going in and out of HDMI display while gaming. Now it doesn't display at all.
    Can a jumper work for either the 0.387n &/ the 0.508n resistors?

    • @idreestech
      @idreestech  5 หลายเดือนก่อน

      Absolutely, the jumper will serve its purpose.

    • @michaelolayinka441
      @michaelolayinka441 5 หลายเดือนก่อน

      @@idreestech I'm doing that now 🤪 💣💥💣
      Thanks in advanced

    • @michaelolayinka441
      @michaelolayinka441 5 หลายเดือนก่อน

      @@idreestech the jumper didn't work for the exact one you changed what do you advice, should I jump the one perpendicular to it. Cuz it failed to boot when I jumped the one parallel to it.
      My RSX is hot I'm not sure it's a reflow I need

  • @zerogaming8967
    @zerogaming8967 ปีที่แล้ว +2

    My ps3 slim 3000 series turns on and then off after 3 seconds no light , changing the psu didn’t work

    • @idreestech
      @idreestech  ปีที่แล้ว +1

      Please watch the videos I've created that address the errors at hand.

  • @Mobile-Tech72
    @Mobile-Tech72 ปีที่แล้ว +1

    hello bro ps3 only beap no any lights......?

  • @sunnyhenry7947
    @sunnyhenry7947 ปีที่แล้ว +2

    This is great job, please how can I can get this reading meter I mean the one for the resistor

  • @kdesignmail
    @kdesignmail ปีที่แล้ว +1

    Great job! With my PS3 i can play for several hours, but if i turn it off and then on again it will not show image... i have to let it cool and then try again.

  • @reshwan_
    @reshwan_ 9 หลายเดือนก่อน +1

    whats the value of that resistor

    • @idreestech
      @idreestech  9 หลายเดือนก่อน

      I could not remember all component's values but for some. You have to verify it from another good motherboard.

  • @adangzls1655
    @adangzls1655 ปีที่แล้ว +1

    Hello, I have a fat ps3 with glod, I have noticed that the rsx does not heat up, do you think that is the problem? Thanks

    • @idreestech
      @idreestech  ปีที่แล้ว +1

      Then check power section for RSX. Switching inputs on inductors.

  • @rabiusharefbabina2844
    @rabiusharefbabina2844 ปีที่แล้ว +1

    Pls my teacher I have super slim PS3 such is the problem like this how to fix it ?

    • @idreestech
      @idreestech  ปีที่แล้ว +1

      You have to configure the fault. If you have tools, you can do it. I have made some videos on PS 3 super slim too. You can watch them.

  • @RelaxingNature1-n6r
    @RelaxingNature1-n6r 3 หลายเดือนก่อน +1

    How to fix PS3 HDMI flickering and blanking problem.3004 A model.

    • @idreestech
      @idreestech  3 หลายเดือนก่อน +1

      The HDMI flickering and blanking issue on a PS3 (3004A model) can be caused by a few different factors, ranging from HDMI cable issues to hardware problems.
      The cable might be faulty, so try using a different one.
      Inspect the HDMI port on both the TV and PS3 for any debris or damage. Sometimes dust or a loose connection can cause flickering.
      Turn off your PS3, then hold the power button until you hear a second beep. This will reset the display settings, which might fix any resolution or compatibility issues.
      After resetting, manually set the resolution to match your TV's native resolution (e.g., 1080p or 720p). Sometimes auto-detection can cause flickering if there’s a mismatch.
      Try connecting the PS3 to a different HDMI port on the TV. Some TV ports may have different processing capabilities that can affect signal stability.
      Connect your PS3 to a different TV or monitor to see if the problem persists. This can help you identify whether the issue is with the PS3 or the TV.
      In rare cases, the HDMI flickering can be caused by a faulty HDMI IC on the PS3 motherboard. If none of the above steps work, it could be a hardware issue that might require replacing the HDMI IC chip or inspecting the GPU for possible damage.
      If the problem continues after trying these fixes, the issue might be hardware-related, and further diagnosis or repair may be required.

    • @RelaxingNature1-n6r
      @RelaxingNature1-n6r 3 หลายเดือนก่อน +1

      @@idreestech thanks 👍

  • @mouhamedkhchini
    @mouhamedkhchini 10 หลายเดือนก่อน +1

    What model of resistor

  • @MichaelDaponte-fy9ji
    @MichaelDaponte-fy9ji 4 หลายเดือนก่อน +1

    Could you just buy the resistor

    • @idreestech
      @idreestech  4 หลายเดือนก่อน

      Yes, you can definitely buy the resistor! Just make sure to get the correct value based on the schematic or the part you're replacing. It’s a straightforward fix if that’s the issue. Let me know if you need help finding the right one!

    • @MichaelDaponte-fy9ji
      @MichaelDaponte-fy9ji 4 หลายเดือนก่อน +1

      @@idreestech thanks

  • @kondwanibanda4219
    @kondwanibanda4219 10 หลายเดือนก่อน +1

    My ps3 slim has no display and the gpu is not getting hot

    • @idreestech
      @idreestech  10 หลายเดือนก่อน

      Check for the HDMI encoder chip or replace it with a good one.

  • @sergiojimenez3415
    @sergiojimenez3415 ปีที่แล้ว +1

    You’re out of this world

  • @rossclarke8028
    @rossclarke8028 วันที่ผ่านมา +1

    Whats a lgiht?

    • @idreestech
      @idreestech  วันที่ผ่านมา

      @rossclarke8028 It seems like "lgiht" might be a typo for "light." If you're referring to the PS3's green light, it indicates that the console is powered on. However, if there's no video or audio, it could be an issue with the HDMI port, AV cables, or a more complex hardware problem like the RSX chip. Let me know if you need help troubleshooting! 😊

  • @makvlogs2323
    @makvlogs2323 ปีที่แล้ว +1

    Well done sir great job

  • @BilalAhmed-hc5vm
    @BilalAhmed-hc5vm ปีที่แล้ว +1

    Bhai jaan mera PlayStation repair hu gaya hai ke nahi

  • @Aleksa.09
    @Aleksa.09 7 วันที่ผ่านมา +1

    Why is ps3 slim so unreliable ?

    • @idreestech
      @idreestech  วันที่ผ่านมา +1

      @Aleksa.09 The PS3 Slim has its strengths, but like any piece of technology, it can develop issues over time. Here's why it might be considered unreliable by some:
      Thermal Management:
      While improved over the PS3 Fat, the Slim's cooling system can still struggle with prolonged use or in environments with poor ventilation. Overheating can lead to hardware failures.
      RSX and CELL Processors:
      These powerful chips generate significant heat. Poor solder quality (lead-free solder) can lead to cracks or cold joints, causing failures like the Green Light of Death (GLOD).
      Aging Components:
      As the consoles age, components like capacitors, resistors, and the thermal paste degrade, leading to various faults.
      Blu-ray Drive and HDD Failures:
      The Blu-ray drive and hard drive are mechanical parts prone to wear and tear over time, causing read/write issues or game crashes.
      Power Supply Issues:
      PS3 Slim models can face power supply failures due to component aging or sudden power surges.
      Firmware Updates:
      Some firmware updates introduced by Sony in the past have caused compatibility or stability issues, making older hardware more prone to crashes.
      To make your PS3 Slim more reliable:
      Regularly clean it to prevent dust buildup.
      Replace thermal paste and pads every few years.
      Use high-quality replacement parts when needed.
      Ensure proper ventilation and avoid prolonged gaming sessions in hot environments.
      The PS3 Slim remains a solid console when maintained well, and it continues to have a dedicated fan base!

  • @asadawad3604
    @asadawad3604 ปีที่แล้ว +1

    Ap kidar ho drees bhai

  • @Magsyboy
    @Magsyboy ปีที่แล้ว +1

    All hail to master!

  • @infinitymobile9922
    @infinitymobile9922 8 หลายเดือนก่อน

    Good video ❤️

    • @idreestech
      @idreestech  8 หลายเดือนก่อน

      Thanks 😁

  • @clambone337
    @clambone337 9 หลายเดือนก่อน +1

    My glod was caused by the rsx chip on my board

    • @lawlietcodm
      @lawlietcodm 8 หลายเดือนก่อน

      did you fix it? how?

    • @clambone337
      @clambone337 8 หลายเดือนก่อน

      @@lawlietcodm i covered a Pennie in thermal paste put it on the rsx to see if glod would go away and it has been working for a good month almost its backwards comp i would get it fixed but its working so no need

    • @clambone337
      @clambone337 8 หลายเดือนก่อน

      @@lawlietcodm you also might have to use multiple depending on how bad it so if one does not work try 2 dont stack if 2 doesnt work try 4 if 4 doesn't that means the solder is not recoverable and needs reballing

    • @clambone337
      @clambone337 8 หลายเดือนก่อน

      @@lawlietcodm i also learned this trick from someone else in the youtube comments they said its a temp fix tho but for me i just put thermal paste on the coin and ofc put new paste on the chip i tried repasting to see if glod would go away but it only did once more pressure was added to the rsx chip

    • @lawlietcodm
      @lawlietcodm 8 หลายเดือนก่อน

      @@clambone337 I fix it yesterday thanks God! I open the rsx chip and clean it and put a thermal paste in the middle and I put back the rsx and it's work!!

  • @copleskas4889
    @copleskas4889 ปีที่แล้ว +1

    Bro you are my angel

  • @jackrich246
    @jackrich246 ปีที่แล้ว +1

    ❤❤❤
    Please do Live streams

  • @Mehdi-x
    @Mehdi-x ปีที่แล้ว +1

    Me it's only when i put my hard drive

  • @arshadalitv6112
    @arshadalitv6112 ปีที่แล้ว +2

    Hello

  • @Armwrsling
    @Armwrsling ปีที่แล้ว +1

    thx🤩

  • @manolitovj
    @manolitovj ปีที่แล้ว +2

    💪💪💪💪🧑‍🔧🎮🎮

  • @piyushgamesoftwarerewa7793
    @piyushgamesoftwarerewa7793 ปีที่แล้ว +1

    Nice

  • @عمارالراجح
    @عمارالراجح ปีที่แล้ว +1

    استاذ ومعلم

  • @arshadalitv6112
    @arshadalitv6112 ปีที่แล้ว +2

    Assalamualaikum

  • @JhonDCHM
    @JhonDCHM ปีที่แล้ว +1

    Exelent

  • @xpaydaymoney8552
    @xpaydaymoney8552 หลายเดือนก่อน +1

    Does anybody know if this TH-camr has a Instagram or discord I can join

    • @idreestech
      @idreestech  หลายเดือนก่อน +1

      @xpaydaymoney8552 Thanks for your interest! I currently focus on helping through TH-cam. Stay tuned for updates if I decide to expand to Instagram or Discord in the future!

    • @xpaydaymoney8552
      @xpaydaymoney8552 13 วันที่ผ่านมา +1

      @idreestech also I want to ask this I was wanting to this out curiosity have you ever tried to make any TH-cam videos on how to fix the PS3 slim no red light of death I've seen barely anybody posting how online TH-cam tutorials on how to fix and I've also got it on my PS3 slim cech 2001a I just got this thing a few months ago it hasn't been displaying it the red led standby mode light and it's hasn't been operating for at least 3 months now and no seems to turn anymore also what should I do about it information on how to fix it very very scarce online

    • @xpaydaymoney8552
      @xpaydaymoney8552 13 วันที่ผ่านมา +1

      @idreestech also one finally question do u have a Instagram or Twitter account i could message you on for more trouble shooting advice also I don't have Facebook

    • @xpaydaymoney8552
      @xpaydaymoney8552 10 วันที่ผ่านมา +1

      @idreestech could I get ur Instagram user please or not have a account I really wanted to ask on advice on how to fix the PS3 slim no red light of death issue please and thank you very much sir

    • @idreestech
      @idreestech  8 วันที่ผ่านมา +2

      Hi @xpaydaymoney8552! Thank you for your comment and the idea for a video. The "No Red Light of Death" issue is somewhat less documented because it's a rarer problem compared to other common PS3 failures.
      Here are some initial steps you can take to troubleshoot and possibly fix your CECH-2001A Slim model:
      Check the Power Supply Unit (PSU):
      Remove the PSU and check for any visible damage (e.g., burn marks, swollen capacitors).
      Test the PSU with a multimeter to ensure it’s outputting the correct voltages.
      If it’s faulty, replace it with a compatible PSU.
      Inspect the Motherboard:
      Look for damaged components like capacitors or resistors near the power circuit.
      Use a multimeter to check for shorts around the power ICs and main rails.
      Examine the Power Button Circuit:
      Check the continuity of the power button and its connection to the motherboard.
      Test for Standby Voltage:
      Ensure the 3.3V standby voltage is present. Without this, the console won’t enter standby mode.
      Reflow Solder Joints (if needed):
      If you suspect poor soldering or micro-cracks, you may need to reflow specific areas on the motherboard, focusing on power-related ICs.
      Replace the Power Management IC (if applicable):
      In some cases, the power management IC may fail and need replacing.
      I’ll consider making a detailed video on this topic to help others in similar situations. Meanwhile, if you need detailed guidance on any of the steps above, let me know! 😊

  • @asadawad3604
    @asadawad3604 ปีที่แล้ว +1

    Pakistan india Bangladesh

  • @jamesavanzado450
    @jamesavanzado450 ปีที่แล้ว +1

    same model as yours, where do I buy the chip

  • @arshadalitv6112
    @arshadalitv6112 ปีที่แล้ว +2

    Sir please apna koi phone number de apse rabta Karna hai

    • @idreestech
      @idreestech  ปีที่แล้ว +1

      Please join me on Facebook.