How to Drain, Fill & Bleed Radiator 05-10 Chrysler 300
ฝัง
- เผยแพร่เมื่อ 8 ก.ย. 2024
- For More Info visit us at: 1aau.to/h/MR/
In this video, 1A Auto shows you how to drain, fill, and bleed your radiator. This video is applicable to the 05, 06, 07, 08, 09, 10 Chrysler 300
This process should be similar on the following vehicles:
2005 Chrysler 300
2006 Chrysler 300
2007 Chrysler 300
2008 Chrysler 300
2009 Chrysler 300
2010 Chrysler 300
🔧 List of tools used:
• Anti-Freeze
• Drain Pan 1aau.to/ode/1AX...
• Floor Jack 1aau.to/ohX/1AX...
• Funnel 1aau.to/oat/1AX...
• Jack Stands 1aau.to/ohi/1AX...
Subscribe: / @1aauto
Check out our playlist:
Chrysler 300 2005-10 1st Gen: • Chrysler 300 2005-10 1...
For More Info visit us at 1aau.to/h/MR/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
![[Full Episode] MasterChef Junior Thailand มาสเตอร์เชฟ จูเนียร์ ประเทศไทย Season 3 Episode 13](http://i.ytimg.com/vi/NlY2uzrALY8/mqdefault.jpg)
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
My Radiator drain peacock is open but it will not drain ..Don't want to do the bottom radiator hose to do it but looks like I'm screwed
What about burping the system for air pockets? You didn't even go in that direction....
If you are draining your coolant, my advice would be go all the way in with it: drain it, then get a quart of a coolant/radiator flush, then fill the rest of the reservoir with distilled water. Drive for a couple of days so the liquid flush can get all over the place, then drain it again. Depending how much crude u have in your system you might gonna have to repeat the process until you get clear water when you drain it. Then change the thermostat housing, use a coolant funnel with a stopper so no air bubbles will get in the system and then fill it with the new antifreeze.
+Mario Tan Thanks for the tip!
Do you think this video should have included loosening the air release by the thermostat before refilling or is that not necessary as long as you burped it with the funnel @a1auto
Replaced head gaskets, water pump, radiator thermostat, cooling fans, relays, cap, and still overheats
Can I still do it this way even if my heater doesn’t work to turn on the heater
You didnt even show the bleeding part eth
Will this procedure work the same on a 5.7 HEMI??? I have a 2006 Chrysler 300c 5.7 AWD.
You boys are great. Saved me A LOT of money
You mixed the original G05 Orange with Green? Thought that was a no no in Chrysler cars??
this is wrong G05 orange Only.
Autozone recommended the same one as the video. I drained the old coolant like the video showed and it then turned pink just like the video???
Green antifreeze is bad in my srt8 it leaks in the summer
Yes they definitely put the wrong antifreeze in there. It's bad for your block especially if you have an aluminum one. If you poured in the green stuff and then it turned pink later it's because you were entire system was not flushed and there was a little bit still in there. It made the green stuff look pink or orangish. Major fail here
What happened to the bleeding part 🙄
You left the air pocket in the engine (you must bleed the top allen-bolt at the pump) and you mixed two different coolants which will most likely block up the system.
Explain.. the Allen bolt????
Got the drain and fill. Didn't see a bleed.
Setting the fan and heat is the bleeding part
Or you can use value..... Newer cars pretty much bleed themselves
So the relief valve on the top of the intake is there for no reason I guess where the top hose is
DO NOT do it this way. It is WRONG. The old coolant is still in the engine block and never got changed. I use a flushing-Tee connected to the hose from the coolant bottle, and put clean fresh water thru the system to flush it all out. Then I put 30psi of air pressure thru the block to push all the old remaining coolant and water out. Flush the rad and coolant bottle, put it all back together. Then open the bleeder valve on the top rad hose housing. Pour straight PINK MOPAR coolant into the Rad via the top Rad Hose. Keep filling the Rad until you see PINK liquid coming out the bleeder. Reattach top rad hose. Cllose bleeder. Put a 50/50 mix of coolant and water in the recovery bottle. Start engine, let it warm up. Open bleeder to let air out. Turn heater on; LOW fan speed, HIGH temp. Wait 15 mins or so, close bleeder. Make sure engine doesnt overheat. Check coolant level in recovery bottle.
Thank you for the feedback! +G Alexander
How many gallons of half and half coolant did you need to refill ? Thanks
This is the correct procedure.
lol these videos are for peopl at home nobody is not gonna do all those steps
Now get to work on the check engine light and tire pressure DTC’s
+Joe Joe Thanks for checking us out!
@@1AAuto can i use cascade dishwasher soap and distilled water to clean everything? Got an 07 300C and the radiator fans exploded and the blades punctured my radiator. Was told i have to replace both the radiator and fan assembly and then i need to flush AND clean everything.
Try to take the drain plug out of my 2013 Chrysler 300 turned it and it just keeps on spinning right or left it just keeps on spinning and nothing comes out what could be the problem
Gostaria de mais informações sobre o crysler 300c v6 3.5, tenho um e aqui na cidade que moro, não encontro mão de obra adequada.
Somente para constatar, meu 300 C tem 150 mil quilômetros rodados e gostaria de saber quais os cuidados necessários para deixar ele em boas condições.
Por favor me ajudem
Do type/brand of coolant matter? I have same vehicle
@1A Auto: Repair Tips & Secrets Only Mechanics Know
Can i use cascade dishwasher soap and distilled water to clean everything? Got an 07 300C and the radiator fans exploded and the blades punctured my radiator. Was told i have to replace both the radiator and fan assembly and then i need to flush AND clean everything. Google and some people in forums say that i can use cascade dishwasher soap and distilled water to clean everything real good.
this is wrong ??
thieres a bleeder screw by top rad hose at engine
what about that, you can not evacuate air in system like this
WTF your gonna have head gasket issues overheating because purging system of air is most important and this mechanic didnt even know about the bleeder screw
DISAPPOINTED, not sure if these A1 videos are worth referencing any longer
Can I do the setting the gauge part at the end of this video after I already tried to do it before and the gauge on the needle didn't set in the middle?? I drove around for a couple days and the car seems fine but it's just the visual of the needle not being all the way in the middle for me
I have a 2006 Chrysler 300c 5.7 / recently drained my coolant/re did this whole procedure but for some reason, when the car is on and warmed up to its level the coolant overflows, it over flows and also I have no hot or cold air/doesn’t even blow. Any reason why? Please respond, give me something
What if the heater is not getting hot what's next
cuanto tiempo dejo el carro encendido para poder apagarlo y poder poner el tapon del deposito ??
Hello bro.. does reservoir chrysler has a vent hole beside the frame😊
took the bleeder valve out of my chrysler 200 2012 located on thermo housing. It appears to have a waxy substance on the threads ?
Does is matter if it’s orange or yellow antifreeze?
I have a Chrysler 309 2006 I removed drain plug to let out all the fluid for some reason I can't get it to go back on please help
Thought the book said flush with distilled water?
Drained old antifreeze out of radiator and tried to flush it but all the fluid stayed in the resivor...it never acted like it went thru the system. Started to overheat a little also. I put a new thermostat in and water pump...whatcha think a clog somewhere maybe or what?
Thanks in advance!
Also the water pump started to get pretty hot...don't know if that's normal either.
any update?
So I did it. The car isn't over heating it's running good. Problem is I'm ment to have 13.8l coolant to go into the system. It's only taken 8l. Why is his?
would it be the same for a 200 touring. do you know if its the same for the newer 200s?
+Brian Stout It may be a different procedure on your application. We currently do not have an auto repair video for this particular year, make and model. Thank you for asking. 1aauto.com
HOW DID YOU BLEED THE COOLANT????
+Julio Lugo Thank you for checking us out. There will be a bleeder valve located near the upper radiator hose, or if you remove the radiator cap and let it pour you could bleed it too. 1aauto.com
What kind of coolant to use ?
Mopar coolant
Zerex G05, works amazing on my 300c. Don't listen to that other guy if you need your car running asap. I guarantee you WON'T find Mopar coolant at whatever store you go to. I see Zerex g05 at almost every autozone i go to.
I think that’s too much coolant for a Chrysler?
Which one do I use for my Chrysler 300c 2006
Hi! I need your help please! How many turns do i need to drain the radiator? Mine just let me do a small 1/4 petcock turn, but then gets very hard to turn another 1/4, i want to know if i need to turn it harder or need air preassure, because i dont want to break the petcock, please!
Did you figure it out.... You need to keep turning until fluid come out
It turns counter clockwise 1/4 turn, then it’s open. Don’t force it past that. Make sure you’ve taken the radiator cap off or it won’t drain properly
there is a bleeder valve for the lower intake yo!...
I appreciate your thoroughness. Your instructions make it easy to understand. Thanks.
What about the bleeder?
*Why you filled two different types of antifreeze ( the yellow **1:35** and the blue **1:49** )?*
LOL, not only that, but neither were the right type either! This car uses HOAT only which is only made by 3 companies.....
What are the companys bro?
@@shroory1990 zerex G05
Thanks worked perfectly 👍👍👍
Lol that car has check engine you mixing coolant that’s not professional at all never saw the bleeding part
+WestPac Mayorga Thanks for the feedback!
Thanks for this video👍🏿
How to bottom hose on 2007 chrysler 300c?
+wargreymon1330 Thank you for checking us out. The bottom hose should have a pinch style clamp which may be moved and the hose separated to remove from the mounting position. 1aauto.com
I did it exactly this way, now my coolant starts to boil and car overheats. Never had an issue before
+Dj TeeOh Check for a failed thermostat.
Same w mine
Which coolant did you use
+vic vergas You will need to use the coolant recommended for your vehicle in your owner's manual.
@@1AAuto but what if you don't have an owners manual A1?
@@erikcaldwell2913 The Car uses HOAT antifreeze only, its sold by Mopar (5 year 100k miles) and Xerex.
Use zerex G05 for Chrysler 300c 5.7
How much coolant did you use? two gallons?
+Eddie Vicente Thank you for checking us out. Please refer to your vehicle service manual for the appropriate coolant required. 1aauto.com
thts not what he asked 1A-Auto ..... its a simple ques , cuz thts my same question
@@caliber8 so same answer that was given caliber8... refer to manual.
10.60 quarts or 10 liters
No bleed?
use a spillfree funnel on the reservoir when bleeding these cars, if you wanna use the bleeder valve to get rid of the air you'll be stuck outside for over 6 hours like i was.
Is this also considered flushing the radiator?
Hell no lol. Don't do what this guy did if you wanna clean/flush your coolant tank.
He never covered the bleeding valve. It's in the title and the only reason I looked at the video. 👎
and you're good to go lol!!
I'm sure chrysler require orange coolant
Hi I open the petcock but the coolant didn’t come out ? Thanks
+Mohammad Elmasri The radiator will drain if there is fluid in there. Thanks for the question and for watching!
+bazsrt8 6.4lt We wouldn't be able to help with an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
No bleeding procedure capture, no coolant specification caveats, no hot system caveat &no fender covers. This video is a fail.
What if you open the petcock valve and no fluid is draining
+Jason Wegner If the radiator has fluid in it and the petcock is clogged, you may want to try to drain it from the lower radiator hose. If the hose needs to be replaced, you might be able to make a small slice in the lower radiator hose which would allow the radiator to drain. Hope this helps you out. 1aauto.com
Jason We
Not what I ask
Fake srt
Lol
fraka callejon it's not an srt though... and I don't see how it's fake either he said 3.5
It's just a 300 touring, has the C and SRT headlights
Honestly the worse video on this. This is the basic method for any vehicle but these 300s suck to bleed. Especially a hemi with dual climate
Will this be the same for the 300C SRT-8?
1A Auto Parts
What kind of antifreeze do i need for a 05 300hemi??
Eleazar Mendoza I use Prestone 50/50 from Advance Auto