Handbrake Adjustment - Peugeot 307
ฝัง
- เผยแพร่เมื่อ 25 ส.ค. 2024
- How to adjust the handbrake (parking brake) on a 2001 to 2008 Peugeot 307. Thanks for watching. Please comment, like and subscribe !.
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2020
Read important information below:
Disclaimer
Under no circumstances will Screwsnutsandbolts be responsible or liable in any way for any content, including but not limited to, any errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in this video, whether by Screwsnutsandbolts or a third party. In no event shall Screwsnutsandbolts be liable for any special, indirect or consequential damages or any damages whatsoever resulting from loss of use, data or profits arising out of or in connection with the availability, use or performance of any information communicated in this video. Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against improper use or unauthorized modifications of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Screwsnutsandbolts recommends safe practices when performing any do it yourself repairs and or with tools seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.
I have no knowledge about mechanical stuff or ever worked on a car. Just fixed the handbrake thanks to your video. After i fixed some issues in the trunk and i feel great now! ♥️
Thanks for watching and well done 👍
Very well explained. Especially about prising the casing out. The other video I watched didn't explain that and I thought my car must be different. I completed it in minutes thanks to your detailed video. Cheers, Martin.
You're very welcome, thanks for watching !
Great video! Thanks a lot 😄
You're welcome, thank you !
Excellent travail
Thank you !
Teşekkürler
Thanks for watching !
Great video, needs doing on mine.
Cheers !
Exellent
Thanks !
Good day, take it easy, today while checking the spark plugs, the spark plugs were oily as if I was taking them out of the oil, what could be the reason for this, there is a bidet misfire in the car pejo 307 1.6 16v 2004 Model Thank you very much for your interest and interest, I subscribed as soon as I saw your beautiful videos
Thank you very much. There are a few reasons for oily spark plugs. Check out this link here: oards.com/oil-leak-into-spark-plug-well/
@@screwsnutsandbolts actually I thank you, enlighten me with the extensive information you have given, I was almost going to change the whole engine
Great video 👍. I have a question its about a peugeot 307 1.4 petrol 2003 on the board computer its showing antipollution fault and the check engine is on, but the car has not lost any power and sometimes the check engine goes off and noting shows on the computer. What can it be ? Thanks anyway 👍👍
I'm not sure why that comes on, there seems to be multiple reasons. It happened to me once before after I ran the car in first gear with just one front wheel jacked up off the ground and spinning. I cleared the error and it never came back. I'm not sure what caused that though. Here's a link to a forum about this error: www.peugeotforums.com/threads/antipollution-fault.20537/
Mine did that. After resetting never came back.
Just got a 207 with handbrake issues (has rear discs), One of the cables seems longer than the other & as a result one of them jumps out of the bracket as the bracket goes really wonky when handbrake is pulled, I have ordered a new cable but would you say i have a caliper issue?, Thanks for the vid by the way!.
It's hard to say until you have a look. The cable could have stretched or the previous owner may have installed an incorrect cable. Check if the pads are worn equally on both sides and also check the function of the the handbrake levers on each caliper.
@@screwsnutsandbolts Thanks for that, I was thinking maybe somebody had fitted a wrong cable, will drop one off & compare it with a new one that has just turned up.
You're welcome, good luck !
New disks, new pads, new cables, one new jaw.. when the car is on jack, handbrake works very good, but when i drive and pull handbrake, only one wheel is blocking, other os freely rotating, what to do?
I'm not sure. It could be a problem with the caliper on that side
I found a hidden error of a hot brake on a Ford: the oil pipe went wrong because of exreme hot , its inner surface closed the pipe. The brake oil could go in the cilinder because of pushed pedal, but could not go back and the pads always worked. After changing the pipe the brake become ok.
Your case is similar tricky.
Is it same on 207?
I'm not sure, as I haven't worked on a 207, but I would assume it's quite similar
@@screwsnutsandbolts i watch some others they show beside gearshift take down plastic and tighten with 10mm screw clockwise!!on mine 207 hanbrake start to be slippery and dont hold on hill so you need to put gear in first or reverse
is it really necessary to be jacked up ⬆️ on a stand ? i just want ti thighten up a bit
You can take up the slack on the handbrake cables without jacking the car up but then it's harder to check if the brake is dragging on either side of the vehicle.
Does this method also fix handbrake imbalance?
This is only a handbrake adjustment. Imbalance between the rear brakes could be a different issue with one side or the other
As I could see in this excellent video, the cable mechanism provides a limited balancing capability with automatic balancing. The surface under the mutter is arched and the ends of the two cables have ball end to fit perfectly. There is not any setting possibility of the cables length when the cables continued with the bowden, or at the end of the bowden outer shell. (Excuse my English.)
See the cable change here: th-cam.com/video/jP6PmOLmlvI/w-d-xo.html
It proves that there is not any setting possibility for the movement length of the cable of the bowden relatively to the bowden shell.
A very good reasoning of the imbalanced hand brake is given here:
th-cam.com/video/ogBTTuaOQLw/w-d-xo.html
If you remove the lever of the brake because of e.g. piston change, you can put it back in wrong orientation. This also can result in imbalancing effect. To avoid this I suggest to mark the orientation of the lever on the axis before removal.
NEVER pull the handbrake up on the ratchet!! Press the release button before using it up & let go when it's set. The amount of wear & tear on the pawl is significant over an extended period and can (and does) result in the handbrake mechanism failing.
Thats the stupidest thing i ever heard . My dad owned cars, i have, and not one single hand brake failed . Why would it fail? They built not to fail. Currently have a 20 year old car with everything original, including the lever. Works just fine . They built to pull it like that.