FlySky FSCT6B Binding/Connecting to Laptop/Channel Reversing and Tuning
ฝัง
- เผยแพร่เมื่อ 25 มิ.ย. 2024
- In this video, I will explain in detail the binding process of FSCT6B in detail and how to connect to your laptop/computer and install the drivers.
Download the drivers from here- bit.ly/2FSCT6Bdrivers
Buy FSCT6B from here - bit.ly/2fsct6btransmitter
Buy cheapest 6 channel transmitter - bit.ly/2fsi6transmitter
Buy FSCT6B from here - amzn.to/2m0WoPW
I will also cover the advanced part like channel reversing setting mode and subtrims. Everything will be covered in detail.
If you like this video give a thumbs up.
subscribe (it's free) - bit.ly/2techbinders
Follow me on social media
/ techbinders
/ akshaysingh192
/ akshaysinghyadav
/ akshay.singh192
Music Used-
"Wallpaper" Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 3.0
creativecommons.org/licenses/...
Music promoted by Audio Library • Wallpaper - Kevin MacL...
"Carefree" Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 3.0
creativecommons.org/licenses/b...
Music promoted by Audio Library • Carefree - Kevin MacLe... - วิทยาศาสตร์และเทคโนโลยี
Amazing video!! Helped me a lot. Thanks
Glad to help u
great bro
Tysm bro ... very helpful
Welcome 😊
i connected my transmitter to the computer, but the controls are not shoing any response. please help me!
I have a similar problem. It shows invalid port number too.If u have found a solution then please help me out.
Helolp full video thanx you🖤
Nice video bro, it helped me a lot.
happy to help u
@@TECHBINDERS thank you so much bro
Bro how much power battery didi you use...?
Bro my throttle is on 37 in the kk2.1.5 control board how can i fix it?... The trims are already in the minimum state
Hi nice video about transmitter binding with receiver, iam also same kit but iam facing binding problem between receiver and transmitter board, not getting solid red light after first connection, even i tried with new receiver which is recently purchased but problem is not solve could you help me how to solve problem
I am looking for this transmitter to play steam games. The problem is that this model is not detected by steam. I want to use flight simulator programs for drone fly practice.
I require some help. Tech Binder, this video was helpful. Although i am encountering problems when i connect the transmitter to my laptop. It says invalid port number. Please help me out as soon as possible.
Also iam on windows 10, that may be a problem.
hii can you suggest some best budget remote for playing almost all simulators ..
go for frsky or flysky rc. they support almost all simulator..
How i factory reset this transmitter
I'm could open the link for drivers in Windows 7 ultimate
Hi
I have connected motor with esc. Esc to receiver 3rd channel. when I connect with battery motor does not spin through transmitter throttle stick.
However if I switch esc connection to channel 1 and connect servo to channel 3. I can control servo through transmitter trottle stick.
Also without transmitter and receiver I can control motor through servo tester.
I am bit confused and blocked what could be wrong here. Any help would be appriciated.
ে
hey thats not only popular in Indian. it is populer everywhere.
Hey just a question, I've started to learn drones and wish to make a whoop drone with camera, so camera and gps operation should be independent of this transmiter and receiver right? If i use this transmitter will i face problem in using a camera and gps on the drone? Also will this setup work for all types of drones like small and big?Please reply urgently.
No problem u can use any camera .just ensure if u are using a video telemetry for transmission it should not be at 2.4Ghz frequency
@@TECHBINDERS thanks bro, you are the best
Welcome
downloaded the driver from discription link
but didnt get install option
bahi m chanals revers kr rha ta pta nhi kya huaa remot ki sbhi stick kam krna band kr gyi trasmitter ko resat kese kre jisse satting maual mode pr aa jaye
Hey...
I have a problem will binding I had kept the esc in ch1....then after binding I started to control the brushless motor from ch 1 .....but now I want it to control from channel 3 so how should I do....
Plz reply ASAP.........
Motor will work only on channel 3 not in any otehr channel, either u have reconfigured channel or there is issue with your transmitter.
As it is working in ch1
The when I tried in ch3 so it is not working nor showing red light
Its is only showing in ch1
It is also ct6b,but not getting binded
Can we setup the receiver with sbus protocol??
yes u can, but this does not have s-bus protocol.
@@TECHBINDERS can we use ppm protocol using ppm encoder module??
bro i want that laptop conected cable how to purches .......pls reply
contact Asus customer support..
Can u give the name of the software used after connecting the tx with the pc for configuring
T6config..it is in the description
The same software can be use for fsia6 transmitter as well?
Fsi6 has onscreen display..so need to update it using software.
@@TECHBINDERS but actually when I'm moving the stick of the transmitter for configuring on the multiwii software it doesn't respond to the movements of the sticks on the screen
Change it through screen..
I have a small problem. The servos on my ailerons arent moving as much as they were with the servo tester. How do I fix this?
Increase the end points for particular channel
@@TECHBINDERS I did its at max 120%. still the angle isnt as high as with using servo tester
There might be some issue, check ur trims whether they arr center or not, check for expo as well
What battery and voltage are you using for the reciever?
It requires 4 1.5v pencil cell. So it operates at 6v..
@@TECHBINDERS can we use normal 2200 mah batteries
What do u mean by normal?
@@TECHBINDERS no rechargable i guess
@@TECHBINDERS can we use 2200 mah lipo battery for esc calibration??
Can I connect 12 v supply directly to receiver without esc
No u should not.. 5v is the max receiver can support
@@TECHBINDERS I tried with 5v by connecting to arduino but it does not showing any light
I followed all the listed procedure still the Config. Says "Invalid Port Number"
😊
It is coming with programming or we have to program it
u need to do channel mixing as per ur requirement
does it need to be set with a laptop after binding?
Yes u need
hi.. i have made a cuadcopter,.. but all the motors are not spinning together ..plz help me out
Sure message me on whatsapp
I have followed your instructions, it is not working. Please help
Bro can i use 11.1 V battery during binding ???
yes u can
@@TECHBINDERS thank you so much bro
@@TECHBINDERS bro but when I connect my ESC was burning bro
@@meeniga.dolendravamsikrish285 The ESC was faulty, it happened to me as well, replace it.
Bhaiya please help me
Mai new transmitter receiver or Motar Liya hu bt Sara connection krne kee Baad Mera Motar q nhi ghumta
Check videos or message me on WhatsApp..
Does it unbind itself frequently?
nope
Does the driver installs/works in windows 10?
Yes,it works
It's not working
Thx very much
But my father does not buy me that transmitter :(
But this was very helpful
Kya ct6b transmitter ko mobile se serup kar sakte hai
I mean setup
Nhi
Mk in more detail
What ??
Who to program whith mobile I don't have PC.
Can't understand, can you be more specific
But how to upload it in the transmitter
Shown in the video.. watch twice
Bat port
My receiver is not getting binded
After all the work. My drone is not responding to controller. Safe mode is on. Self level is on. On through pass-out all motor are spinning but when I leave the 1 & 4 button controller got dead and nothing happen
You might have damaged your board
@@TECHBINDERS why it is running all motor on through pass-out mode??
It runs all motor to check whether they are starting at the same time or not..
I have done like you told but it is not happening
Bro i don't know what's the problem with my transmitter but switches are not working i mean no visual response of switches on the application for fsct6b. Can you help me?
Reset the transmitter using reset file..search online the file
does this have a gyro?
U mean gyro sensor ?
@@TECHBINDERS yes. the one which is used to stabilize a rc car
No
How much pro?
?
Brooo I Am Not Angreji I Like Punjabi
my friend, i suspect there is a good information but that music makes me feel like i am watching a very young child's movie or something. just a friendly critizim. i will try to make it through as i can see you put some work into it and you care about your work
Couldn't open the link for drivers
What prblm u are facing?
@@TECHBINDERS I couldn't open the link for the drives that u gave
Bhahiya mera transmitter meter botton kam nahi kar raha hy please help me....
?
@@TECHBINDERS apse contact kar na hy... please help me...
Main new flysky ka ttransmitter le kar aya per ESC calibration ke baad motor nahi ghum raha hy... software per dekha to wo wala button work nahi kar raha hy....
Please help..
Bhai... Mera transmitter and receiver work nhi kr rhe hai.. Bahut tension me hu kese sahi kre please help me
Try to bind it through mentioned process in the video
hello bro my drone is not flying
Transmitter ki programing karna jaruri hai kaya please batao🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏
yes
My port number is invalid !!
This may sound strange, but just put a USB 2.0 in between your laptop/pc and the transmitter. The transmitter should plug into the USB hub and don't connect it directly to your laptop/pc. It has worked for me. Hope it helps.
How to save the settings
Please saying in hindi
Meri cable toot gayi h laptop me insert karne ke baad detect hojati h par red light nahi jalti
contact customer support
not working in windows 10 bro
I will pay you if you solve my problem
🤬🤬