How To: Setup FlySky i6 for Multirotor Drone Eachine i6 Turnigy i6 and More
ฝัง
- เผยแพร่เมื่อ 26 ก.ย. 2024
- If you'd like to see a tutorial on something else drop a comment below and I will consider making a video.
Hey guys just a quick(not so quick) tutorial on how to setup this transmitter for use with a multi-rotor running CleanFlight or BetaFlight. Hopefully this helps someone out there just getting started. If this helps please don't forget to hit that like button.
Thanks for watching!
Channel mapping still not working
Angela Cervera If there is no movement at all then there is 4 possible reasons for that..
1. You are not bound to the receiver.
2. You have the wrong connection type selected. (example: you have ppm selected when using iBus.... or you have iBus selected when running pwm)
3. Your receiver is plugged into the wrong port on your flight controller
4. You are connected to the right port on the flight controller BUT you have not enabled serial Rx on the correct port in the Ports Tab
Hi RCFlyer85, I have tried all those options and none of them work, could you give some advice regarding #2 on the setting that should work. ie tried randomly multiple configurations with no luck
dale b what receiver do you have?
The same one you're using in the vid. Stock not updated.
dale b ok and how do you have it connected? PWM with all 6 (1 3 wire and 5 1 wire) wires, PPM with 1(3 wire connection ) or iBus with 1 (3 wire connection)?
Out of the countless hours of research and no one to show me what I was doing wrong,by far you have been the most helpful!! hands down,thanks
Thanks so much for the help. Now I’m flying endlessly
built my 1st quad set it all up then found that throttle was wrong spent half a day searching for the answer and found this video
cheers Brother for the simply fix
Great video, started off a bit rocky, but you recovered and did well! Keep up the videos and fly safe. I am a single engine aircraft pilot and a commercial drone pilot! Good job. Thank you!
Thank you so much. Your video fixed my issue that I had been working on for hours!
Trevor Williams Glad to hear that... that's why I do it. Happy Flying!
Thank you so much, I am new to this RC world and your video helped me with my first quad. You are the best!
Aiz That's what it's all about.... Glad I could help!
Hey man I followed your instructions down to the dot but at 9:32 nothing moves in cleanflight like yours does. BTW im glad i found your video Ive been trying to figure this problem out for a while. your video def helped me out a ton so far!
If you check out my comments to Angela Cervera (it should be pinned at the top of the comments) you'll see what I have to say about that. Hopefully that will help you out. Keep me updated
This is awesome! Added this to my VERY USEFUL playlist for quad-copters! Thanks!
your video saved my life. well, someone's life. that thing about holding the cancel button to save settings "everybody knows" - it's not in the manual that i can see.
atomictraveller Really? I never looked at any manual personally. Yeah it's sooo weird that they wouldn't at least make it long pressing the OK button.
Anywho glad I could help
TJ W Neither did mine but I assume he means an online manual
First time drone user needed help and you did it perfectly. Cheers bro
Great vid. I know it's laughable for most flyers but for us beginners, without videos like this it can be baffling so thank you. Is mode always on ch6 and arm ch5 on every quad though.
No you can change it around if you'd like but 1-4 are always going to be the same so ch5&6 are your only free channels unless you do the 10ch mod
Great video Sir, loved the plain speaking easy to follow instructions and just subbed ya!
Rick Flare Awesome... Glad you liked it. Thanks for watching!
Awesome video but I need help finding that wire that you connected to the receiver from the drone like when you said make sure not to dod that because the wire was unplugged. Ya that wire i need but I cant find it
Thanks man! I've been scratch building fixed wings for several years, but never built or even flown a "real" quad. I have a tinywhoop and like it and was wondering if I could use my radio with a bigger quad... I guess so. Now I just have to build it.....and probably rebuild it a few times to.
Depends what sort of radio.
If something like this a hobby grade radio sure.
If like one of those cheap little video game controllerslike come with many whoop packs , probably not.
And even if you could ou should probably just get a real radio that has proper gimbals and everything like this one least.
Did everything as per the video. I still cant change the values with the transmitter, i.e, in betaflight, the values do not change. p.s: the receiver port on the FC is ppm/sbus, i connected my receiver (the same one that u use) into that.
pls help
Thank You for the quick response. JR
Yahoooo!! at last, now I switch switches and my micro brushless starts and changes flight modes, its been weeks; no actually its been months and all I could do was scratch my head..Thank you..
EVIL TREE FPV Glad I could help!
Thanks for showing the right way to do things . I have a problem with getting my transmitted to work on screen like you have and my calibrations so off left is right right is left so I need help bad
Angela Cervera Like throttle is on the wrong stick or do you just need to reverse your channels?
Is there a big difference between IA6 receiver and iA6B setup? I got my Wizard in and bound the receiver to it and controller successfully (connected the quad to channel 1 on the receiver), set up the arm switch on the controller (SWD) and tried to power up quad and controller and I'm not getting anything when I flick the arm button. Not even a hiccup. Also no throttle response. Is it necessary to update using beta flight? Or should it at least respond out of the box w the receiver connected to it?
Hi, I'm a super boob, but I wanted to know, if I'm suposted to leafe the resever in the Drone or, If I should unplug IT again, when everything is set up 😁(or in other words should I fly with the resever?)
Receiver stays in
@@RCFlyer85 thanks😀
I’m a little confused. I followed Another build tutorial and he didn’t do this. I don’t have power for the receiver to bind it. How do I power it?
You'll need to either have an external 5v source or hook it up to the drone and plug the battery in
Props off for safety!
Hello: Have a question for you that you may help me with???? I'm new to fpv and my wife surprised me with a Eachine Wizard X220 FPV Racer Blheli_S F3 6DOF 5.8G 48CH 200MW 700TVL Camera w/ FlySky I6 RTF and of course there are no instructions that came with it and I have no idea how all this is supposed to work. Now I got to the point where I got the fpv and my googles to work and I was able to pair the receiver with the drone but I can't get the motors to start. So I did some more research on you tube and down loaded Beta Flight and connected the drone with my computer to check out the operation. Well when I tabbed down to the receiver tab and it opened there is no info. According to other posts there are different color horozonal bars that show up to correspond with the different radio controls and would move when you would move each control. Well on my system there are no color bar and no movement when moving the controls. I can't find any instruction on how to go about checking what would cause this problem? So is there any instruction you could give me on how to go about and what to check so I can make the controls work, I think if I can figure this problem out this will fix the problem of the motors not wanting to ture on?. I hope I explained and made sense on my problem. Thanks for your help I watch your channel all the time and have learned a lot so thanks again.
John
I'd start with updating to the most recent version of betaflight and then you will need to set up everything all over again...
Please help me,
I have the exact same receiver and transmitter as you do, but I am using a SPracing F3 Flight controller, I have binded my receiver with the transmitter, I have followed all the steps and I have selected the right configuration settings.
However, once I'm at the channel mapping, the throttle on betaflight doesn't move when I move the throttle on the controller
What version of betaflight is in your flight controller?
I connect mine and nothing pops up in my lab top
Im getting a happy model mantis that comes with one of these i6 transmitters so glad I can bind it to other stuff
i am me Yes the i6 is a really functional TX though the RX's are just so so
RCFlyer85 im new to all this it's definitely better than my hubsan x4 tx i will get a taranis later on but for learning betaflight and binding the mantis and this look perfect 😁
Thx bro!
There has to be one more problem with my setup:
In betaflight all the signals from the radio do what they should, so that's fine. If I go to "motors" i can spin the motors, also fine. But when i desconnect my drone from the computer, restart the drone and the controller, i arm it and i set a flightmode, nothing happens. I can only see that the flightcontroller responds to my radio. Can somebody help me out?
please help. when i bind the rx battery shows up but it just keeps beeping and does nothing
Hi thanks best explained flysky setup
Definitely helping me. But Km still lost. Lol Thanks
Hi got one problem . for some reason my little one pulled out all my cables out of my machine i6 what colors goes where ...
M SBW There is no standard really so I couldn't say.... Honestly it doesn't matter as you can remap them in BetaFlight/Cleanflight
hi i have a few questions i binded my mobula6 quad , i hear a beeing sound from the transmitted all the time and the rx is flashing , how can i turn that off? also in beta flight when i turn the motor stop on , and save the quad doesnt arm at all?
It's been a while since I've messed with this stuff so it'd be hard for me to help you currently..... Sorry.
why is it when I try to configure my Eachine i6 remote controller in Libre Pilot, when I check to see if the remote is responding correctly with the on screen controls for throttle, pitch , roll and yaw, they do not move in the right direction on the screen that they should be moving {when I move throttle up the on screen controls show that the throttle being moved downward instead of upward. How can I fix this problem. Thanks
gerald j You need to reverse your channels... You can do this in Libre or in the transmitter itself.
If you still cannot bind like the remote wont say bind ok, your powersupply current might not be enough. I ran 1 amp and it wont bind but as soon as i ran it with a 2 amp charger it will bind instantly
I decided to buy eachine wizard x220 big jump from bugs 3 and 6 do i need to connect transmitter to the computer i can't get it to fly
Hi sir , i want to build my drone
i have sp racing f3 evo v2 and receiver fs-a8s and remote fs-i6 and motors
i solding the board with motors and receiver ,what i should do next ??
My transmitter is not responding like yours is when you go to betaflight I check if all the channels were in the right place but I checked all the channels
same as yours but I don't know what I'm doing wrong
Angela Cervera But how is it wrong? You have to be specific so I can help you.
I know this is an old video, but when i get to the receiver tab in betaflight, my sticks are at (A)1537, (E)1527, (R)1504 and my all sticks only go down to 1030-1060... Should i just trim them?
I wouldn't... Do it the right way
I have a dji flame wheel. The flysky FS-i6 is missing so I need to program another one which I bought with the FS-i6 flysky reciever and bind it. How do I know if it's clean flight or Betaflight? What else do I need to know to get it to fly.
I haven't touched drones in a while... I honestly don't remember anything about this receiver. Sorry I can't help
@Ed Straker Thank you for your assistance.... Hopefully he gets (got) it working
Sorry, I don't understand wht you're doing here. Why is the receiver loose when you bind it with the Radio and the quad? I'm new, forgive me.
Because when you bind you physically have to push a button. For demonstration purposes it was easier to have the receiver outside the quad.
@@RCFlyer85 I thought this radio automatically would bind to any new quad without extraneous devices.
@@xpane depends on your setup...
@@RCFlyer85 So I need to put the FS-IA6B receiver on my Tinyhawk? Seems too heavy for the little guy.
@@xpane yeah that's too big for that... You'll want the A8S
Hi, Angele can you help me set this up for hexell-x in cleanflight, I mean set the flysky.
That’s exactly what I’m looking for , one thing - does it work with orange cube FC ?
Unfortunately, I don't really follow drone stuff like I used to so I am unfamiliar with that FC
What Happened from 9:24 to 9:26 when the video skips. That is where I get stuck, my Controller does not talk to my receiver.
What happens if my bar isn't all the way full does that mean am not bond please help
Great video.. does this work with the eachine novice 1?
Can you bind this controller with the Tinyhawk 2 freestyle?
Will this transmitter work on the Clearview flight simulator ??? ----------- Thanks!
Do you need any extra cables aside from what comes in the box?
I don't know.... I've never purchased a controller alone so I don't know what comes in the box.
HELPED ME BRO THANK U MUCH
The same, fs-ct 6b tx and rx, and yes I have movement in the receiver tab
Thanks RCFlyer85:
I have a Turnigy I6 from 2015.
The Model Name will not show up on the screen after I name the model and save.
If I use say Model 06 and call it Drone06 and save, it shows up on the main screen as
Turnigy 06. Tried many times and it will not show the name properly.
Other than that I have to remember what turnighy xx is, all other features work fine.
Any suggestions to fixes?
Tnx Bob
Robert Steele Is this in AFHDS ( Not 2A ) mode? It should say right on the front screen either AFHDS2A or AFHDS. If you are not in 2A mode I don't think it saves the names that way but other than that I'm really not sure unless it's just something from the Turnigy firmware that could probably be fixed by updating your transmitter
It is in Mode AFHDS2A
Found out it is a Turnigy I6 Bug in Firmware
I bought the unit in 2015 and have not updated firmware Since I may brick my tx. Just have to remember the planes quad assignment.
Thanks bob
what digital transmitter is compatable for echine e120 heli
there us no movement on mine too. Its not letting me change uart 1 to serial rx but i was able to change uart 2 to serial rx. I do have it on serial based receiver and ibus.
scottyandthefenders Don't ever change UART1 to anything other than MSP.
if you set UART 2 to serialrx and you have no input first make sure that you were actually bound to the receiver 2nd make sure that you actually have the receiver plugged into UART 2 and not UART 3 and lastly make sure on the configurator that you have the receiver type set to serial and set to ibus
Thanks for you help but im still having trouble. there is no UART 3 shown on betaflight so i assume that my reciever is plugged into UART. my reviser type is set to serial and ibus too. Also when i go back to my old tx and reviver which is the em 16 (www.google.com/search?q=jjpro+em-16&espv=2&biw=1366&bih=662&source=lnms&tbm=isch&sa=X&sqi=2&ved=0ahUKEwiokPK_ibHSAhUp_IMKHd6yDSsQ_AUICSgE&dpr=1) and change my settings back to MSP on UART 2 and PPM Rx input evertything works fine. Also i am using the fs Ia6 plugged into channel one not the IA6B that you used in your video.
I am falling in love with the hobby and just want to go fly again haha thanks for your help!
Worked, thx !
Damn, I'm now running backwardsI got my motors working and when I tried to re calibrate, I messed up.
Clean flight failed to recognise my com port, I uninstalled and reinstalled installed the driver again, device manager fails to show the driver( can't find it in c drive either). I don't know what to do. Please help me. By the way thanks for ur reply earlier
sri vamsi You are just having the worst issues it seems... I don't think I could help you further without actually being there in person. Maybe you can find someone local to take a look at it. Sorry I can't do more.... Best of luck
Thanks man, helped me out a bunch!
Hey, I can't find not one video on TH-cam about how to connect a FS-ia6b reveiver to a kiss flight controller. This is my first build. Thank you so much. It would be even better if u could do a vid on how to do that.;)
Droneva Bass because it's pretty much won't work.... KISS doesn't support iBus unless you flash it to BetaFlight. There are a few other ways depending on your particular set up but not using the ia6b
Thanks for the lighting fast response. What do I do know because I don't have any more money to get a spectrum or taranis x9d?
Droneva You could...
--- Without flashing to BetaFlight
Run PPM (if that board supports it)
Get an i6x or Turnigy Evolution TX which supports SBUS output and a compatible RX like the ia6c or X6B
--- With flashing to BetaFlight use what you have (ia6b) in iBus mode
So could I get the turnigy evolution that comes with a tgy-ia6c receiver and it will work with the kiss flight controller?
Droneva Yes... Check out this video
th-cam.com/video/_rAjPHKfuTo/w-d-xo.html
What ever you had done I also could able achieve but when I move my throttle motor is not responding. Any suggestion.
Clean flight is responding if I change throttle.
When you move the throttle does the throttle channel move or is it a different channel?
@@RCFlyer85
Yeah I I move throttle throttle bar in clean flight responds according to the movement.
@@vasanthakumarvelkumar3776 Could be any number of things. You'll have to take the time to troubleshoot. If possible try and find someone local to help out
@@RCFlyer85 thank you
i had successfully bind a8s with fs i6 on my eachine ex110 but quad not responding, its my first racer, please guide.
Fish and Aquarium Lover you'll have to set that up in betaflight or cleanflight whichever one you're using and try using S Bus or I bus
Thanks for your video!! It helped me finally get my modes setup for my Furibee Fuuton 200. I'm stuck with a Eachine branded i6 transmitter, and I can't set the buzzer up. None of the other aux switches work. Plus is there a way to backup or save models if the transmitter get destroy or damaged.
George Grazette What receiver does it have and what do you have set up so far? Are you using any switches currently?
RCFlyer85 Flysky FS-A8S.I just ordered 2 ixb receiver ..the buzzer works when I shut the transmitter off, but I want on on the transmitter. I setup Arm on switch A, switch C is Angle, Hozion & Acro.. No Airmode made my motors spin up too much. If I update the firmware on the transmitter will I lost my previous model's ? Plus having to use sliding the tabs to get into setting will that be gone too.?
George Grazette I can't remember what all gets erased when you mod your controller since I did it so long ago so it's best to assume that it will erase everything. I personally don't know how it goes on the Eachine model though if you flash the official mod it should get rid of the need to slide the tabs. with your current set up if you're not using 3 flight modes you can set arming and two flight modes on the 3 position switch and that would leave another switch or Knob open for your buzzer or whatever else
can you use the other type of receiver for this?
the stock one it comes with which port?
thanks!!!!
ultra rc Not sure what RX you are talking about but this transmitter works with most FlySky AFHDS 2A receivers like the... A8S, X6B, iA6C, iA6 etc
Hi its srivamsi again, the driver's good. Everything seems good. I tried flying, the motors aren't spinning at once (I'm guessing) ,the quad's not flying straight. I calibrated manually with receiver and also from the gui but still it's acting same. I don't know much about pids I didn't change pids. Can u please help me?
sri vamsi Make sure your sticks are centered at 1500 without drift on the receiver tab... Also do a accelerometer calibration
RCFlyer85 thank for the help I brought the stick values as close as possible to 1500 and calibrated accelerometer. now the motors are responding good while flying the quad's going forward while I move my throttle stick forward. kindly help me make this stable
my motors aren't responding to either the tx or the gui (clean flight) I was trying to map throttle response from min to Max, kindly help me
sri vamsi Does anything move on the receiver tab in CleanFlight? What receiver and TX are you using
This helped me so much thanks!!!
I can see that my receiver is connected (because i can see the telemetry coming back) but when i go into betaflight, the reciever simply isnt there.
Sometimes the board needs to be powered up for Betaflight to see that.... So try plugging it up. Just make sure the props are removed first. Just in case 😉
@@RCFlyer85 yeah, I've done that sooooo many times, but no luck
@@carsonbellak956 perhaps it's not connected to the board correctly or not in the right port..... Hard to tell without seeing it.
@@RCFlyer85 no, I get you. I'm getting help from another random stranger on The nternet, so bye for now
Thanks for the tutorial! Subscribing for more for sure!! Keep it up!
FunkPV Thank you I appreciate it!
Right here on your time 9:14 my transmitter is not moving like yours mines not moving at all
Hello
Flysky has FS-i6 controller and dron which is flip32 control card.
Can you help with flight settings?
Thank you
Bayfen Bursa you have to be more specific than just flight settings what exactly are you trying to set up? Do you have the receiver bound and working correctly?
Thanks for share bro
RCFlyer85: Nice Video and Thanks.
Question on an aspects of FailSafe setup.
This was not covered, but perhaps you have experience with also the Failsafe mode.
In BetaFlite has two options, 1: fall out of sky, 2: Land
In RX (IA6B) Failsafe setup, all six channel can be programed. So if I set say RX channel 3, Throttle in RX to lowest point (Throttle off) on the failsafe setup of RX screen.
Suggests to me the Quad will just fall out of Sky.
On the other hand, in Betaflite if it is set to
land. Which is the Master, I.E. does the quad react to the RX or Flight Controller?
Which is superior? Seems it might be the FC but not sure?
Thanks BobFlyer
Yeah I'm not sure which one is superior but I set both. Channel 3 to 0% and set it to drop if BF... If you really wanted to know you could just test it
Thanks for all your time in posting this. I see you binded to your custom built drone. Can I bind to a Bugs 3 and Bugs 4, or any pre packaged drone ?? How’s that done ?
Most premade drones have their own proprietary software so in general no you can't. There are modules to emulate "some" of those signals for other transmitters but I've never used any so I couldn't help you much there.
RCFlyer85 thanks for the reply. I’ve seen some other videos where people have bound to pre made drones, so I just assumed it was easy to do. It also explains why those drones already come with their own controller. So...., maybe they can be modded, just not usually done. Thanks again.
hello! subbed! you are a pinnacle of knowlege. watched 15 vides, FINALLY yours explains it slowly, and understaNDING the concepts. i just got this radio at the thrift store for 2.50 and want to use it my quads. I will order some of the reciever parts that goes to the quads (i got some walkera 250's I want to bypass the Devo 710 and use my F6) I set it up as you instructed. would have never thought of that. thanks man truely, I am learning each day trying not to overspend. I will look for a few cheapie recievers, do they come with the cables to attach? I know i can direct power to a small battery or 4aa, something 4v-6v i immagine, yes>? anyway. tons to learn thanks again.
devo project on hold.
quick question why should multi rotors be setup on plane or glider? i set mine up on fixed pitch heli am i doing something wrong?
ShiestyFPV That's just the most common way of doing it and simpler in my opinion but hey if you set it up your way and it works more power to you. I think the logical explanation is that quadcopters actually fly more like planes than they do fix pitch and collective pitch helicopters. But hey there's more than one way to skin a cat
As a beginner, which flysky model would you advise? So many different models of flysky receivers. I'm making wood planes and gliders.
Sorry so late appearantly TH-cam hasn't been giving me notifications for a while and I just noticed...
Depends on how many channels you need but most likely the ia6b or ia10b would be best for you
I just bought the ia6 transmitter +ia6b receiver for 38 euros at bnggd. I think the telemetry of the ai6b can be important in time. I don't need 10 channels.
Oh ,ok
so will will this transmitter work with the Rx31d is a DSM2/DSMX compatible 4 channel micro receiver with twin on-board 2A ES
??
Manny Silva No it will not
How would I change the arm from the left stick to the sw a
You do that in Betaflight
Great vid helped me a lot now that's set do you have any vids on pid settings I'm a newbie so I don't know anything thanks jim
jim thumm No PID videos here but there's plenty here on TH-cam... I've watched plenty and still don't fully understand what to do lol...
Good Luck and Happy Flying!
Have you messed with your Raptor 390 lately? You been able to get your LED pinouts to work on that FC?
Hans Yeah my led works just fine... I have an 8 LED board all programmed and working just fine
One more thing I brought the transmitter separate not rtf they told me I had to buy the other receiver fs ia6b
sir i have a problem in my fs-i6, after i factory reset it the sensor list is gone, so my receiver cant detect my esc bec. how can i restore my sensor list? when i plug the bec the receiver cant detect and nothing appear in my fs-i6 monitor.
joenelle ocsalev Not to sure at the moment... Not near a transmitter. Was your TX modded?
my transmitter sir?
i don't know if my transmitter is modded sir, but my fs-i6 is in factory default.
btw sir my receiver is fs-ia6
Hey bro, you still got that Walkera Rodeo 150 ? You said you were selling it for around 80, I was wondering if you would do 75, ? I was able to scrape together atlesst that much!!?
Nope it's spoken for already.... sorry
It really helped me! Thanks a ton
We don't need laptop for uploading software?
Modern Tech Yes you will need laptop after the steps in this video
Very helpful thanks👍
Your very welcome... Thanks for watching!
Which Flight controller is used
Thx good info keep it up
thank u it helped me a lot
So I'm curious if you know how to add another aux switch. Currently I have swa and swc programed but I would like to add swb for a buzzer mod, but I cannot for the life of me figure out how to add another aux switch to program. If you have any knowledge on that, I could use some help.
Cooper Hilton You have to make sure you have the correct receiver and you'll need to do the 10channel mod to enable more channels on a stock FS i6
Oh goodness. So the Flysky 2.4G 6CH FS-iA6B Receiver wont work with this?
Cooper Hilton Yes the ia6b will work but only on ppm or iBus. the question is what transmitter do you have if you have the original I6 transmitter it is only capable of handling six channels so for 4 controls and two switches you will need to do the 10 Channel mod if you would like to get control of all of the switches at the same time
Yeah I believe I have the original. Its the FlySky FS-i6 2.4G 6CH AFHDS. Looks like I'm going to attempt the 10 channel mod.
Sorry I'm a noob but do you have to use the beta flight or can u just go fly once it's set up on the thing where you plug everything in
The Doonst3r Yes you still need to verify and setup things in BetaFlight
Thank You!
hello friend I'm model airplanes I'm starting with drones so I do not know much about it. I hope you can help me bought a holybro Shuriken 180pro only that did not have the receiver version for flysky only for frsky, I bought anyway so I bought a receiver for my flysky i6 radio. I installed the receiver I made the bind but when I enter betaflight it does not have communication with the radio will the friend can help me thanks I await a response 👍
Hobby in Japan What receiver did you get?
RCFlyer85 follows the link of the receiver Flit10 2.4G 10CH Micro Telemetry Flysky Receiver Ibus compatible for FS-I6X FS-i6S Turnigy Evolution. banggood.app.link/0YUfsOsq5L
Hobby in Japan Well I really never recommend non OEM receivers and have never heard of that one... I would say double check your wiring and make sure your ports are set correct and that iBus or Sbus( whichever that RX supports) is selected
RCFlyer85 friend to get thank you
I have a problem with my Flysky I6x radio and my newly purchased Eachine E010S. It has the F3 flight controller with built in Flysky Receiver and I can get the radio to bind but I for the life of me can not get the radio to control the motors. I am fairly sure i have it bound to the FC because the blue light indicates that process is successful and it shows the movement of the throttle and etc. in Cleanflight but when I plug the battery in the motors start spinning and I have no control what so ever. My first thought is that I am doing something wrong during the configuration in Cleanflight but I have been trying with the E010S for 3 weeks almost now in my spare time but I have yet to have any luck and I even have had a couple of friends that fly UAVs try to help me understand and we have all been stumped with the issue.....CAN SOMEONE, ANYONE PLEASE HELP ME CORRECT MY ISSUES?
Adam Bostic If the motors spin when you plug the battery in that means that you need to change the motor pwm rate to 16000 I believe the CLI command is " set motor_pwm_rate = 16000 "
Other than that make sure that everything is working correctly in the receiver tab. Make sure the values are going from 1000 to 2000 for all channels
can you recommend a good beginner RC helicopter radio....something not too expensive or difficult to bind....I am looking to get a radio that will bind with the Blade or WL toys BNF model helis.....thanks
Gary Vale The only way your going to be able to control multiple brands and protocols is getting something like a Devo10 and highly modding it. You'll have to do a lot of research on different protocols and how they interact with each other
thank you ...as you are the only one who explained about the different protocols.....I will see which brand heli uses what protocol and go from there....2 different radio manufacturers might be best for me .....can you tell me what are the most common protocols used for the popular BNF helis ...thanks again...
Gary Vale The most popular out is FrSky, Spektrum and FlySky
thanks ...I will begin to search out these brands...is there any simple way to know what protocol the various BNF type helis use ...such as Walkera or Blade or WLtoys.....that would help me select a radio ....
Gary Vale Well Walkera uses their own proprietary stuff. Blade uses Spektrum dsm technology and I can't remember WLToys one but you can't really expect to fly hobby grade stuff and "toys" with the same transmitter. Basically at this moment in time your safest bet is to get a FrSky transmitter like the Taranis Qx7.... If you plan to buy specifically Blade products then your going to want a Spectrum Transmitter that's capable of DSM, DSM2 and DSMx
Can this be bounded to an Eachine EX2h?
Not sure....
How did you get 2 arm to light up mine doesn't light up I'm so close
I think it prevents you from arming while connected up Betaflight so it probably won't. Have you tried with it disconnected
yea, I Really crunched some vids today. I finally got it. i learned how to set a failsafe, set the arming. the problem i had was TRIM! can you believe it?!?! so basically, i had to set all the levels to 1000 lower and 2000 upper, as close as I could get. it turns out, that i only set the throttle at 1100, not 1000. so all the settings were under arming range AND YES, THE CONNECTION WAS ALSO THE PROBLEM. craaaazy. now it works, it runs, it's smooth, i also did this funky calibration where i connected to ct, went into motor tab, connected battery, clicked motor on all the way to 2000, plugged in, made funky sound, slammed down to 1000 with manual switch another sound... after that, it was golden. Half the problem was learning the controllers terminaligy, and the other half was the cleanflight. took me a2 weeks a few hrs every night, but its finally my b@#$@ch. well, i gotta test it. but also settting up a throttle curve, and someday, i'll update the 6 channel to 10. need that stupid cord to usb though. cheers man for real. i still have so much to learn man. but it's sinkin in. not bad for a pawn shop pickup. i'll do a video soon.
@@Kriswixx Nice.... So what drone did you get?
not sure, some pawn shop random flier. In hindsight, it prob wasnt the best purchase, but I wanted to get my hands "wet" in the build process by seing one already made. I somehow made the camera and the camera transmitter in the back stop working, so that's the next figure out what's what.. but for the most part, i took the camera stuff off, even if I loose it first flight, at least it's stripped lol. Not sure, some pawn shop thing. not able to identify it. Has a sp pro board though, and been a cleenflight junkie since. I have a buncha spare parts too! almost all i need, but uart cables really. i saw some ebay links.. you know, the Nickle and dime stage. I may put on a 2 prop for test, i only have one set of 3 props it came with...
Is there a way to make drone not flip over? I don't want to crash anymore
its gg There's a few things that could cause that... You'll have to get to the root of the problem. Usually props on wrong, motor spinning the wrong direction, motors in the wrong order (ie motor 1 is where motor 2 should be)
no no, my drone is fine, i just dont want it to have the ability to flip over if you get me
its gg Oh.... Well the easiest way to do that is only fly in Angle Mode or if you are Horizon and would like to roll but not flip you could set up dual rates to limit your pitch to around 70 %
I am new too this and I know you said to set up a failsafe and I know
That is important. Can you please show how to set up a failsafe?
th-cam.com/video/0QrcF3TVo7w/w-d-xo.html
CGI guy thanks
Can i use this transmitter with wakera 250 racer and vortex 285 drones.
jose ramos Yes... It should work with both of those assuming you also add a receiver
I bought the eachine wizard x220 do i need to conect this transmitter to the computer? I have no idea I'm jumping from bugs 3 and 6 to racing
You might have said but does the fs-ia6A work the same way?
abowch zey Somewhat.... Honestly I don't recommend that receiver as it has pretty short range
RCFlyer85 thanks
RCFlyer85 sorry other question is the RC-B the same as this?
do the sticks not reset to the middle
Depends on how it's setup but most people fly racing/freestyle drone controllers where the throttle stick does not auto center. So these come usually like that with the throttle side not self centering.
thanks for the info sir
Ricky ThePhoton Dexter No problem I try my best to pay it forward to the hobby. Thanks for watching!
with the flysky fs t6 can I use ppm
vape guy 261 yes