I know you mentioned working on the repair is a reason you don't record, but as a new tech, I am very grateful. I'm working on one of these for the first time on Tuesday for the same error code and I appreciate it.
I have this washer. We have 2 huskies and cats but the filter at the bottom is almost always clean and never has to be pulled out. Is this normal? We are getting the leaking water code for the top one almost every time we use it. Should we replaxe the hose?
Hello, my flex washer won’t turn on-! No codes, no lights-etc.. I have power at outlet and power to (noise filter Voltage reducer-) How can I get washer to turn on - ??? Help!
Hey I have the same washer but every time I try the smart install it doesn’t go directly to AS any reason why it happens also my lower washer isn’t function properly it doesn’t spin or allow access for water
What a heck of job man, I like the way you throw parts around 😂😂😂, great vedio , any vedio about the flex dryer? And how much your labor for this piece , just curious . thank you again
As the owner of an appliance service company there is no way in Hell I would do warranty work,especially at this level with the high liability of damage to the machine and surrounding area and hours of labor. What a joke. C.o.d is the only way to go and I charge 300 just to diagnose one of these ,let alone do repairs.
I have experience with this model.. if there is no leak(s)? Then its most likely a “software” problem. Unplug the control unit to reset the error code then plug it back and if the code comes back? Then you have to replace the two sensors at the bottom… i found it easer to jack up the machine, go under it and use a mirror to locate the sensors and swap them out.
I got a 1SC error code which indicated it was the top washer drain pump which was a headache to get to but i did it however after replacing it i still got the same code after running a test cycle. At this point I don't know what else to do or look for.any suggestions would be highly appreciated!!
Why would you show us how to elevate or offset a Factory Safety Flood Sensor to protect a home from being Flooded out causing Thousands of Dollars of damage, all you got to do is install a $2 Dollar Disc, which is a factory up date part for the overflow problem in the Fabric Dispenser drain out into the Mini Washer never lift that Flood sensor to by pass a Error code 1L C1 ....
I have a question. I have the Samsung flex washer and can’t find any info anywhere. You have worked on these so I’m helping you can point in right direction. It’s started to make a jet engine sound, during spin cycle. My wife researched and ordered me a housing bearing to replace. It came and appears to just be a metal plate attaching to bottom of top washer tub? Doesn’t seem right at all ?? Any help greatly appreciated
You and I have the same exact problem. You need new bearings HOWEVER samsung does not sell new bearings for the model, according to the internet you have to buy a part that isn't available anywhere. What you sound like is you have the spider arm that sits on the back of the unit.
What do you think is a reasonable price and can you fix it on your own? Out of warranty I charge by serial number. The newer the more it cost to fix. Some people tend to jst buy a new one as it gets older. These washers are not produced anymore the design was bad.
never raise the water leak sensors how will the home owner know if they have a water leak doing Thousands of dollars of damage to there home??? just fix the leak do your job... insurance company's will do a thorough inspection on that leaking washer on a insurance claim and take pictures that you raise the sensor on film and deny home owners claim, i cannot believe you did such a dumb thing on film and posted it on the internet... WOW... that sensor is there for a reason to protect the floor from a flood... just crazy move...
Samsung techline authorized and has a service bulletin on the raising of sensors. They are clearly aware of the issue with customers overloading detergent and softener. It leaks out the left side of that hose clamp.
2018 Samsung Flex Washer #WV55M9600AV/A5. Dual module (top washer) lid latch is broken and cannot be used since it won't latch. SEARS shows that lid latch is not sold separately and my understanding the whole Washer tub cover lid Part#DC97-20036C needs to be replaced. The problem is that lid#DC97-20036C No longer manufactured. Is there a part # for just lid latch??? 3 years washer and parts already No Longer Available??
yep sad that you got buy the whole lid assy. and you say they no longer sell it... WOW... i just installed one about 6 months ago... i see them on amazon just now $230 and you say they don't sell them ??? and yes they do not just sell the latch...
@@johncasor9698 The lid assembly DC97-20036c was OOS everywhere when I looked online, local appliance parts and the official Samsung website said that no longer manufactured or something like that. Sears show that it's available to order now. Btw...how difficult was it to replace it and how much time it took for you?
I really want to buy this set but im not sure now. Is Samsung service really that bad and are parts really scarce??..I see many happy people with this set snd many say their horrible pieces of junk. I hate this 😒
nothing but issues with this wash machine. ruined my floor, service and customer svs is not good. also have a new Samsung Refrigerator that's a piece of junk.. Buying the most expensive appliances didn't work out foe me.
most samsung washers after 5 years no parts available especially computers. this flex washer many people love the top mini washer and many people never have used it... Haha i work on these a lot and they stop making them about a two years ago. but i still do a lot of service calls on them...
Gawd i hate these machines. Their dishwashers, fridges, stoves microwaves are all trash. Ofcourse they look great but wont last. Get the warranty and plan on replacing after year 7-8yrs under medium use.
yep i work on these washers 5 days a week more then 8 hours a day and never did what he did toss things and put tools on a dryer without a towel under the tools. if i act this way i would be fired... there is cameras in many homes i go into and mics video running on me all the time... he is a nut case i think...
I know you mentioned working on the repair is a reason you don't record, but as a new tech, I am very grateful. I'm working on one of these for the first time on Tuesday for the same error code and I appreciate it.
New tech here, thank for this. I'm doing a bearing job for one of these and never saw one when I was training. Life saver
U know how to change the spider arm?
The repairman seems he is mad at the homeowner the way he throws the parts over sink and top of dryer glass.
WHY did you remove the Main Computer & disconnect all the rear top wire harness ???
I have this washer. We have 2 huskies and cats but the filter at the bottom is almost always clean and never has to be pulled out. Is this normal? We are getting the leaking water code for the top one almost every time we use it. Should we replaxe the hose?
Good break down vid, 2x4s are clutch... also, time for a vacation huh 😎
Wow the way you were trowing those parts! I would kick you out of my house immediately
Then you have to put the parts by yourself
@@kamalabbady6778I would prefer doing that than a guy like you working on it!
This helped me get front panel off to change diaphragm.. inside bottom deteriorated.
Gotta love these beat downs..like a kick in the junk
Hello, my flex washer won’t turn on-!
No codes, no lights-etc..
I have power at outlet and power to (noise filter Voltage reducer-) How can I get washer to turn on - ???
Help!
Anyone know if you have to remove the front to replace the rubber door seal? I couldn't find a video for this model
Hey I have the same washer but every time I try the smart install it doesn’t go directly to AS any reason why it happens also my lower washer isn’t function properly it doesn’t spin or allow access for water
Side note, how you have your bits bugs me.
You really don't give a damn how you carelessly throw the customer's parts around.
Do you have the same model Samsung Flex Dryer? Trying to replace a cracked drum.
What a heck of job man, I like the way you throw parts around 😂😂😂, great vedio , any vedio about the flex dryer? And how much your labor for this piece , just curious . thank you again
The warranty was Home Depot Asurion they pay low at that time it was around $195 for many hours of work.
As the owner of an appliance service company there is no way in Hell I would do warranty work,especially at this level with the high liability of damage to the machine and surrounding area and hours of labor. What a joke. C.o.d is the only way to go and I charge 300 just to diagnose one of these ,let alone do repairs.
Nice video.Good job.
THIS WASHING MACHINE SHOULD HAVE A SMART CONTAINER TO BE ABLE TO WASH CLOTHES BECAUSE IT IS TOO BIG. GREETING FROM BRAZIL.
Hey can u help me a bit error
Code 1dc4 code
Latch also won't lock ither . What do u think it could be
I have experience with this model.. if there is no leak(s)? Then its most likely a “software” problem. Unplug the control unit to reset the error code then plug it back and if the code comes back? Then you have to replace the two sensors at the bottom… i found it easer to jack up the machine, go under it and use a mirror to locate the sensors and swap them out.
What’s the sensors called?
I got a 1SC error code which indicated it was the top washer drain pump which was a headache to get to but i did it however after replacing it i still got the same code after running a test cycle. At this point I don't know what else to do or look for.any suggestions would be highly appreciated!!
Why would you show us how to elevate or offset a Factory Safety Flood Sensor to protect a home from being Flooded out causing Thousands of Dollars of damage, all you got to do is install a $2 Dollar Disc, which is a factory up date part for the overflow problem in the Fabric Dispenser drain out into the Mini Washer never lift that Flood sensor to by pass a Error code 1L C1 ....
Samsung service bulletin approved unfortunately the manufacturer doesn’t even care about you consumers if they are authorizing it
I have to change the spider arm on the lower washer lol trying 2 see how I am going in.
I have a question. I have the Samsung flex washer and can’t find any info anywhere. You have worked on these so I’m helping you can point in right direction. It’s started to make a jet engine sound, during spin cycle. My wife researched and ordered me a housing bearing to replace. It came and appears to just be a metal plate attaching to bottom of top washer tub?
Doesn’t seem right at all ?? Any help greatly appreciated
You and I have the same exact problem. You need new bearings HOWEVER samsung does not sell new bearings for the model, according to the internet you have to buy a part that isn't available anywhere. What you sound like is you have the spider arm that sits on the back of the unit.
What does a repair like this (minus throwing parts) cost if not under warranty?
What do you think is a reasonable price and can you fix it on your own? Out of warranty I charge by serial number. The newer the more it cost to fix. Some people tend to jst buy a new one as it gets older. These washers are not produced anymore the design was bad.
This guy comes to my house to repair something working like that, I make him buy me a new machine, tooooooo rough 👎👎👎👎👎
never raise the water leak sensors how will the home owner know if they have a water leak doing Thousands of dollars of damage to there home??? just fix the leak do your job... insurance company's will do a thorough inspection on that leaking washer on a insurance claim and take pictures that you raise the sensor on film and deny home owners claim, i cannot believe you did such a dumb thing on film and posted it on the internet... WOW... that sensor is there for a reason to protect the floor from a flood... just crazy move...
Samsung techline authorized and has a service bulletin on the raising of sensors. They are clearly aware of the issue with customers overloading detergent and softener. It leaks out the left side of that hose clamp.
The washer has been working fine since that repair. Your pretty dumb looking on you tube for repair solutions lol
I need help with my washer
2018 Samsung Flex Washer #WV55M9600AV/A5.
Dual module (top washer) lid latch is broken and cannot be used since it won't latch. SEARS shows that lid latch is not sold separately and my understanding the whole Washer tub cover lid Part#DC97-20036C needs to be replaced. The problem is that lid#DC97-20036C No longer manufactured.
Is there a part # for just lid latch???
3 years washer and parts already No Longer Available??
Yes the whole lid needs to be replaced a very fun job good luck
yep sad that you got buy the whole lid assy. and you say they no longer sell it... WOW... i just installed one about 6 months ago... i see them on amazon just now $230 and you say they don't sell them ??? and yes they do not just sell the latch...
@@johncasor9698 The lid assembly DC97-20036c was OOS everywhere when I looked online, local appliance parts and the official Samsung website said that no longer manufactured or something like that. Sears show that it's available to order now.
Btw...how difficult was it to replace it and how much time it took for you?
@@Resist_JWO_1984 very easy to replace and about 20 mins to do this job...
I really want to buy this set but im not sure now. Is Samsung service really that bad and are parts really scarce??..I see many happy people with this set snd many say their horrible pieces of junk. I hate this 😒
Don't Buy Samsung....!
nothing but issues with this wash machine. ruined my floor, service and customer svs is not good. also have a new Samsung Refrigerator that's a piece of junk.. Buying the most expensive appliances didn't work out foe me.
most samsung washers after 5 years no parts available especially computers. this flex washer many people love the top mini washer and many people never have used it... Haha i work on these a lot and they stop making them about a two years ago. but i still do a lot of service calls on them...
To be paniced is understandable warranty jobs pays less on such a complicated time consuming laborious jobs
Are you closed to Los Angeles california?
Texas
I hate working on these.
What’s the part number of the name of the part?
Assy pcb display
good info but very hard to watch video.
Gawd i hate these machines. Their dishwashers, fridges, stoves microwaves are all trash.
Ofcourse they look great but wont last. Get the warranty and plan on replacing after year 7-8yrs under medium use.
I couldn't watch anymore, throwing things around like you're angry.
Try doing this yourself and see how angry you will be.
@@Resist_JWO_1984 no I won't be angry because i love what i do , hvacr , major appliances and i do it without complaining.
yep i work on these washers 5 days a week more then 8 hours a day and never did what he did toss things and put tools on a dryer without a towel under the tools. if i act this way i would be fired... there is cameras in many homes i go into and mics video running on me all the time... he is a nut case i think...
I’d smack the shit out of him throwing a screwdriver and pieces around on my $1800 washer
@@johncasor9698
I agree, he is a nutcase
Alex jones
Also stop using so much soap. More soap doesnt makenit work better. 95+% of you are doing it.
Ww4w