Excellent video! I recently purchased a used JLG T500J and just ordered an Analyzer. Thanks for the info! Any regular maintenance videos would be very much appreciated!
Great videos! I picked up a 2015 400S and an analyzer. What is the best way to familiarize myself with the complete operation of the analyzer? How do I clear the trouble codes?
Hi Manuel, I had a bunch of codes on my analyzer. I pin out cables check power modular found out it and the contractor was bad. so i change them out. I dont have any more canbus errors or lift problems on my code reader. but now i have an open contactor or relay. It is new , I guess i could have got a bad one. I need to check the voltage between the terminals to make sure i have 24 volts. Any ideas. HELP
Hello Manuel. We have the mode T350. The scssor lift can work without the foot put on the ground, for us it's not safe. How you allow operation only when the 4 foot are on the ground for safety ? does it need configuration or what. Tks
Hey sir do you encounter a fault code 6621 for TH514 telehandler it says boom angle sensor can bus failure we already change all the platform and rear harness we changed the POWER DISTRIBUTION BOARD AND UGM new Boom angle sensor.
Good morning Mate, this video really help, I am working on one scissor lift now, jlg 2669, the machine was working okay but the operator sparks the battery and that's were main circuit board burned, so I order new board and installed already, I started machine okay,but alarm beep and all controls not working. Can you help me. Thanks
My JLG 3246ES is leaking fluid from the steering hydraulic bar. I believe the seals are worn out. I am curious how difficult it is to replace the seals and how complicated is it to add the fluid lost.
It’s fairly easy common problems on this unit 4 bolts to hold the steer cylinder and 2 hydraulic lines . Just make sure you don’t put the new ones in backwards. And to fill the fluid is easy Allen bolt mounted on the reservoir
Have you ran into any tilt sensor canbus failure code on 1932i/R1932? I have 24V/good ground and 2.5 on can to the sensor, tilt sensor value on analyzer shows ???, replaced with new and no change. Can’t calibrate either.
Do you know if this will help with Skytrak telehandlers? Im planning on getting a little fleet and we need to get some diagnostic tool. One of the code I got 101:16 on one rn. Any ideas?
I have a 2008 JLG 2630ES, I have a 25 fault code that shows drive and lift prevented. This happened after some battery issues. Now I have to charge the batteries with a separate charger and it won’t lift or drive, any help would greatly be appreciated.
Sounds like the issues is around the charger cause if wired wrong it will prevent you from driving or the batteries wires make sure they are hooked up correct and your not missing one . Check behind the batteries to see if you’re missing a whole lead connection that you might have missed
@manueldiaz I'm having issues with a jlg 1932es. I don't have the diagnostic tool but I do see that on the control station it has the tilt light on and also the lightning bolt flashes. The machine doesn't go all the way up and the alarm sounds once it stopped 10ft high. Any ideas what it might be or what I should look for?
Hola desde Chile lo vemos Tengo un problema con un equipo 2030 Es, coloque el analizar y le aparece logger help: 1._ canbus failure 2.-startup Que significa eso
If you google “Jlg analyzer” Amazon might have some in stock but I know they can get kinda pricy, that code is from the digital indicator next to the battery isn’t it?? How’s your lift acting up??
Lift the unit about halfway . In the middle you’re gonna see the cylinder with a black reservoir where the fluid goes in. It’s usually a size 6 Allen wrench to unscrew
Hello there I have JLG 1930se couple months ago stopped driving back and forth and I was trying to figure out what's wrong by taking the batteries out to test them, nothing was wrong with them and after I put them back and now it doesn't operate up and down any idea how to get fixed or what it could wrong with it? I appreciate in advance
Excellent video! I recently purchased a used JLG T500J and just ordered an Analyzer. Thanks for the info! Any regular maintenance videos would be very much appreciated!
Great videos! I picked up a 2015 400S and an analyzer. What is the best way to familiarize myself with the complete operation of the analyzer? How do I clear the trouble codes?
Hi Manuel, I had a bunch of codes on my analyzer. I pin out cables check power modular found out it and the contractor was bad. so i change them out. I dont have any more canbus errors or lift problems on my code reader. but now i have an open contactor or relay. It is new , I guess i could have got a bad one. I need to check the voltage between the terminals to make sure i have 24 volts. Any ideas. HELP
Hello Manuel. We have the mode T350. The scssor lift can work without the foot put on the ground, for us it's not safe. How you allow operation only when the 4 foot are on the ground for safety ? does it need configuration or what. Tks
Hey sir do you encounter a fault code 6621 for TH514 telehandler it says boom angle sensor can bus failure we already change all the platform and rear harness we changed the POWER DISTRIBUTION BOARD AND UGM new Boom angle sensor.
Question I changed the control box on unit from a bigger unit how do I change the model ?
Question jlg 2032es won't move forward or reverse. Everything else works. Code 256 but the sensors seem to be testing good
Watched your video. Just got a question how do you clear error codes
My code reader also says charger plug in. Is there any way to check the charger once i pull it out of the lift 1930ES
Good morning Mate, this video really help, I am working on one scissor lift now, jlg 2669, the machine was working okay but the operator sparks the battery and that's were main circuit board burned, so I order new board and installed already, I started machine okay,but alarm beep and all controls not working. Can you help me. Thanks
Yeah anytime you install a new computer or board on Jlg you need to program it to the machine. Once you do that the alarms will go off
My JLG 3246ES is leaking fluid from the steering hydraulic bar. I believe the seals are worn out. I am curious how difficult it is to replace the seals and how complicated is it to add the fluid lost.
It’s fairly easy common problems on this unit 4 bolts to hold the steer cylinder and 2 hydraulic lines . Just make sure you don’t put the new ones in backwards. And to fill the fluid is easy Allen bolt mounted on the reservoir
Have you ran into any tilt sensor canbus failure code on 1932i/R1932? I have 24V/good ground and 2.5 on can to the sensor, tilt sensor value on analyzer shows ???, replaced with new and no change. Can’t calibrate either.
Is the tilt value trough analyzer showing 20-20?
Morning Manuel, I keep getting error code ES002 and no one knows what it is. Controller flashes 3 quick, pause then 1. Any idea?
i have a jlg 3969 , cant drive. why?. for lift up/down, and steering ok. only no respon for drive foward and reverse
Do you know if this will help with Skytrak telehandlers? Im planning on getting a little fleet and we need to get some diagnostic tool.
One of the code I got 101:16 on one rn. Any ideas?
2014:8042 QSB3.3
I have a 2008 JLG 2630ES, I have a 25 fault code that shows drive and lift prevented. This happened after some battery issues. Now I have to charge the batteries with a separate charger and it won’t lift or drive, any help would greatly be appreciated.
Sounds like the issues is around the charger cause if wired wrong it will prevent you from driving or the batteries wires make sure they are hooked up correct and your not missing one . Check behind the batteries to see if you’re missing a whole lead connection that you might have missed
@manueldiaz I'm having issues with a jlg 1932es. I don't have the diagnostic tool but I do see that on the control station it has the tilt light on and also the lightning bolt flashes. The machine doesn't go all the way up and the alarm sounds once it stopped 10ft high. Any ideas what it might be or what I should look for?
Sounds like the unit just needs to be re-calibrated , tilt is out center
@manueldiaz7723 thank you.
Scissor lift 4394rt can you show me , how to remove elevation angle sensor with hand held analyser. I like your videos
What year ? You can test it manually depending the style of the sensor
Hey bro I have a JLG 2630 And is running slow up and down
Can you help ?
Could be the pump but you can change speed trough analyzer sometimes tuning up the specs fixes issue
Hola desde Chile lo vemos
Tengo un problema con un equipo 2030 Es, coloque el analizar y le aparece logger help:
1._ canbus failure
2.-startup
Que significa eso
MERCI BEAUCOUP
Where can I get one I have a e5002 error
If you google “Jlg analyzer” Amazon might have some in stock but I know they can get kinda pricy, that code is from the digital indicator next to the battery isn’t it??
How’s your lift acting up??
eBay or Amazon
That’s the code on the bottom of LED correct ?
Is your unit not doing anything at all?
I need help with this analyzer
Hey big brother I have JLG R4045 and I'm having some issues
Those are a nightmare lol what you got going on with it
Helllo, how to fill hidravlic oil in cilinder for JLG 1930es????
Lift the unit about halfway . In the middle you’re gonna see the cylinder with a black reservoir where the fluid goes in. It’s usually a size 6 Allen wrench to unscrew
@@handymanny214 thank you
@@handymanny214 Normal or reverse thread?
I have JLG 3246ES CANMUS ERROR CAN YOU HELP ME
I help you brother come to my channel
Bro how to calibration upload video
Jlg 800aj can't travel and can't steer and no error code
trying to reset pump have error 995 power module error
Mmmm 9/9 code on a JlG? Could be mosfit short
What year and model you got ?
Hello my fiernd
Hindi
Hello there
I have JLG 1930se couple months ago stopped driving back and forth and I was trying to figure out what's wrong by taking the batteries out to test them, nothing was wrong with them and after I put them back and now it doesn't operate up and down any idea how to get fixed or what it could wrong with it?
I appreciate in advance
Mmmm sounds like you have a short somewhere. Are you getting a fault code ?