To clean the filter on your SimplyGo oxygen concentrator, follow these steps: 1. Ensure that the concentrator is turned off and unplugged from the power source. 2. Locate the air inlet filter on the device. It is typically located on the bottom or side of the concentrator. 3. Gently remove the air inlet filter from its housing. The filter is a small, rectangular or circular piece. 4. Rinse the filter under running water. Use mild soap or a gentle cleaning solution if necessary. 5. Thoroughly rinse the filter to remove any soap residue. 6. Shake off any excess water and allow the filter to air dry completely. 7. Once the filter is dry, carefully reinsert it into the filter housing, ensuring it is securely in place. Regarding the machine getting too hot, there are a few potential reasons for this issue. Here are some troubleshooting steps to try: 1. Ensure that the device is placed in a well-ventilated area and not obstructed by any objects. 2. Check if the air inlet and outlet vents are clear of any debris or obstructions. Clean them if necessary. 3. Verify that the device is not operating in a high ambient temperature environment. Excessive heat can affect the performance of the concentrator. 4. If the problem persists, it is recommended to contact the manufacturer or a qualified service technician for further assistance. They can inspect the device and diagnose any potential issues that may be causing the overheating. Remember, it is important to follow the manufacturer's instructions and guidelines for maintenance and troubleshooting specific to your SimplyGo oxygen concentrator model.
It’s the same machine that you have on this video, can you show us how to remove the filter on video instructions. Please 🙏 I deeply appreciate your help!
You can definitely use oxygen with a CPAP machine. Here's more information: www.oxygenconcentratorstore.com/blog/connect-oxygen-concentrator-cpap-machine/
Need technical support for a internal error, machine just working for 2 minutes and stops 🔼,has a triangle simbol every time when shutting down. Any place near Miami for a technician?
I purchased a used Simply go machine and found that it has an issue, am I able to have this serviced somewhere? I purchased it from an individual not a service provider.
SimplyGo battery lasts around 50 minutes on 2 LPM continuous flow. If you are using it a lower setting, please get the unit serviced or replace the battery.
Hello dear, I have a device that maybe wasn't working for a while, as you mentioned it should run at least 10 hours a month. It's now start for 20 sec and turns off... Is there an obvious solution?
If your SimplyGo portable oxygen concentrator is turning off after running for only 20 seconds, it's essential to troubleshoot the issue to determine the cause. Try turning off the concentrator, disconnecting the power source (if connected), and removing the battery. Wait for a few minutes, then reinsert the battery, reconnect the power source, and turn the device back on. This can sometimes resolve minor issues.
The unit is not able to detect breath. Check the connection from the cannula to the device. Make sure the nasal cannula is properly positioned on your face and that you are breathing through your nose. Make sure the cannula tubing is not kinked or obstructed.
If the device is operating in the carrying case, make sure it has been placed correctly in the case so that the outlet vents are in the front. The vents should be visible through the slot at the bottom. If the alert persists, contact your vendor.
Why does this not keep up charging with the car charger on high settings? And it blows fuses in my vehicle, maybe I can run it without the battery and it draws less amps plugged into dc car charger?
At high settings the time required to charge the battery will be much longer and at the highest settings, it may not charge at all. Please refer to user's manual.
Yes, SimplyGo will work without battery from wall outlet only. However, the manufacturer does not recommend it since the machine will stop working, without any alert, in case of power outage.
This is my favorite one you can use this one to sleep with at night I need one but Medicare and United Healthcare won’t cover these portables some great government we have so keep on dreaming I do😜
we have the same device but the power key do not start the device ı have try also without battery to start the lcs screen is coming but after touch the key twice it, will be black no screen ı have try to solve the problem without battery and whit battery , the battery is also80% full it was not solved I think the key also this touch key do not react after put it twice maybe the power card is damaged ??? I need your help ı am out of usa at the moment
So out of the 10 hours per month runoff, you can break down doing all the AC/DC and battery rotations that rise to the level of 10 hours run time for compressor and lube and filters. Not additive I presume.
Ensure that the battery has sufficient charge. Some POCs may not operate in continuous flow mode if the battery level is too low. Charge the battery fully and try again.
respironics makes a good home machine , but the simplygo is junk, no one can fix it , i have one and i am getting ready to smash it with a sledge hammer.....
This is such a great video!!!
Mine stopped working on continuous only runs on pulse now
Great Video. Thanks. Question, if I may: my unit beeps (6 times) but still provides oxygen. What might be the problem?
Please refer to the user's manual or contact customer support. We cannot diagnose the issue with the information provided.
Thanks
Is it better to buy or rent. How often should one test purity and maintenance
Our Oxygen Specialist would be happy to help you out with your requirements. Please give us a call at 888-909-1477.
I sure wish I had watched this when I first bought my POC...
Does this unit need its filter to get cleaned regularly? if yes, how?
Munawar Rasul a patient can’t replace the filter it’s internal and requires a repair technician to do the job.
can you be a little more specific? what kind of repair technician can replace the filter? How often does it need to be replaced?
Good info. thank you
Thank you!
How to clean the filter? I am using this oxygen concentrator, why is the machine getting too hot? I need help pls.
To clean the filter on your SimplyGo oxygen concentrator, follow these steps:
1. Ensure that the concentrator is turned off and unplugged from the power source.
2. Locate the air inlet filter on the device. It is typically located on the bottom or side of the concentrator.
3. Gently remove the air inlet filter from its housing. The filter is a small, rectangular or circular piece.
4. Rinse the filter under running water. Use mild soap or a gentle cleaning solution if necessary.
5. Thoroughly rinse the filter to remove any soap residue.
6. Shake off any excess water and allow the filter to air dry completely.
7. Once the filter is dry, carefully reinsert it into the filter housing, ensuring it is securely in place.
Regarding the machine getting too hot, there are a few potential reasons for this issue. Here are some troubleshooting steps to try:
1. Ensure that the device is placed in a well-ventilated area and not obstructed by any objects.
2. Check if the air inlet and outlet vents are clear of any debris or obstructions. Clean them if necessary.
3. Verify that the device is not operating in a high ambient temperature environment. Excessive heat can affect the performance of the concentrator.
4. If the problem persists, it is recommended to contact the manufacturer or a qualified service technician for further assistance. They can inspect the device and diagnose any potential issues that may be causing the overheating.
Remember, it is important to follow the manufacturer's instructions and guidelines for maintenance and troubleshooting specific to your SimplyGo oxygen concentrator model.
@@Oxygenconcentratorstore Thank you so much 🙏
It’s the same machine that you have on this video, can you show us how to remove the filter on video instructions. Please 🙏 I deeply appreciate your help!
Filter is deep inside machine and requires some disassembly to be accessed.
Please, I would like to order a unit of this type for the respiratory system of a young female patient
Our Oxygen Specialist would be happy to help you out with your requirements. Please give us a call at 888-909-1477.
Will the oxygen tube connect to my CPAP machine?
You can definitely use oxygen with a CPAP machine. Here's more information: www.oxygenconcentratorstore.com/blog/connect-oxygen-concentrator-cpap-machine/
I have one and it connects to my CPAP with a special connector so that it is feeding tho oxygen right into my CPAP tube. Works great
Hello! How often does my Respironics SimplyGo need to be serviced? Is there a time in hours? Thank you in advance for your response!
It depends on the usage. The unit will alert you when the service is required and you can continue to use it for 30 days and send it in for service.
Need technical support for a internal error, machine just working for 2 minutes and stops 🔼,has a triangle simbol every time when shutting down.
Any place near Miami for a technician?
Please contact your equipment provider (where you purchased the concentrator from) or the manufacturer to get your unit serviced.
Are the sieve beds user-replaceable?
Please contact your equipment provider for SimplyGO sieve bed replacement. SimplyGo has no user-serviceable parts.
sir my mother is on oxygen support of 2 lpm of continuous flow, if i get this machine what will be the pulse setting on the simplygo?
SimplyGo can supply 2 LPM on continuous flow mode.
All your videos are informative. You need a real table for display purposes. Sell this one at your next yard sale.
Please it you please plug the machine into wall with charger it will charge without it turn the machine on ?
SimplyGo will work on wall outlet while charging the battery.
Is this model too heavy for a backpack? Is this model still current?
The model is still available and is the smallest continuous flow POC. Backpack is not available for this unit.
I purchased a used Simply go machine and found that it has an issue, am I able to have this serviced somewhere? I purchased it from an individual not a service provider.
Please contact Repair Authority, Ohio, they'll be able to help you out.
hola tengo un concentrador portatil philips simplygo, cambie la bateria varias veces pero dura solo 40min, gracias si me ayuda con alguna solucion
SimplyGo battery lasts around 50 minutes on 2 LPM continuous flow. If you are using it a lower setting, please get the unit serviced or replace the battery.
Hello dear, I have a device that maybe wasn't working for a while, as you mentioned it should run at least 10 hours a month. It's now start for 20 sec and turns off... Is there an obvious solution?
If your SimplyGo portable oxygen concentrator is turning off after running for only 20 seconds, it's essential to troubleshoot the issue to determine the cause.
Try turning off the concentrator, disconnecting the power source (if connected), and removing the battery. Wait for a few minutes, then reinsert the battery, reconnect the power source, and turn the device back on. This can sometimes resolve minor issues.
Run on battery until flat?
Is it good for battery to keep full or run it until flat each time?
While using the unit remove the power cable when the battery is full. When storing the unit store is at half charge.
Is there an internal watch type battery in this machine?
We are not aware of that. For service requirement, please contact authorized service center.
The fact that a $2000 piece of equipment can "overcharge" and a damage the battery is absolutely ridiculous.
Talk to our Oxygen Specialist for a free consultation, please give us a call at 888-909-1477.
How to use or start that machine oxygen
Watch: th-cam.com/video/CYfpbq-VTG8/w-d-xo.html
Pada mode pulse oksigen keluar sendiri tanpa dihirup. Bagaimana cara memperbaikinya?
my simplygo is beeping with an “nb” and alarm bell 🔔 display.. appreciate advice on how to fix it pls ? thanks
The unit is not able to detect breath. Check the connection from the cannula to the device. Make sure the nasal cannula is properly positioned on your face and that you are breathing through your nose. Make sure the cannula tubing is not kinked or obstructed.
Pls help asap my oxygen turn of immediately with triangle appears pls what can i do
If the device is operating in the carrying case, make sure it has been placed correctly in the case so that the outlet vents are in the front. The vents should be visible through the slot at the bottom. If the alert persists, contact your vendor.
Why does this not keep up charging with the car charger on high settings? And it blows fuses in my vehicle, maybe I can run it without the battery and it draws less amps plugged into dc car charger?
At high settings the time required to charge the battery will be much longer and at the highest settings, it may not charge at all. Please refer to user's manual.
@@Oxygenconcentratorstore I did and it doesnt say much
sir does simplygo work without battery (plug in only)?
Yes, SimplyGo will work without battery from wall outlet only. However, the manufacturer does not recommend it since the machine will stop working, without any alert, in case of power outage.
My SimplyGo Autostarts on power all panel switches work except Power On/Off. I changed main PCBs and front panels but no solution. Pls help, xns.
Please do not conduct the repairs yourself, unless you are an authorized repair personnel. For repair related issue, please contact the manufacturer.
I have a problem with my simply Go I need help it works for 2 minutes and after make 3 beebs and sign 🔼 after switch off
There's an internal error and the unit requires repair. Please contact the closest repair facility.
This is my favorite one you can use this one to sleep with at night I need one but Medicare and United Healthcare won’t cover these portables some great government we have so keep on dreaming I do😜
Not true...I have medicare and United Healthcare AARP and have had one for 3 years now.
we have the same device but the power key do not start the device ı have try also without battery to start the lcs screen is coming but after touch the key twice it, will be black no screen ı have try to solve the problem without battery and whit battery , the battery is also80% full it was not solved I think the key also this touch key do not react after put it twice maybe the power card is damaged ??? I need your help ı am out of usa at the moment
Please contact your equipment provider (where you purchased the concentrator from) or the manufacturer to get your unit serviced.
what is error code 0030
What's your unit make and model?
So out of the 10 hours per month runoff, you can break down doing all the AC/DC and battery rotations that rise to the level of 10 hours run time for compressor and lube and filters. Not additive I presume.
Thanks for your comment
Hi..i just want to ask why does my simply go alarm when put it on 1.5lpm then after less than 2mins it shuts down? What should i do? Thank you.
Please contact your equipment provider. They'll help you out with the issue.
NOISY
My device turns off when I switch it to any mode other then pulse….
Ensure that the battery has sufficient charge. Some POCs may not operate in continuous flow mode if the battery level is too low. Charge the battery fully and try again.
respironics makes a good home machine , but the simplygo is junk, no one can fix it , i have one and i am getting ready to smash it with a sledge hammer.....
Please contact your equipment provider or the manufacturer to get the device repaired.