This is a very helpful video and made the job of changing the boot lid switch itself quite easy to carry out. I had more of an issue with emptying the boot Thank you Night Hawk
Thank you for the very clear instructions. The hardest bits were getting the plastic cover off the lock and putting the felted plastic part on at the end. Job done!
This is a wonderful video. Thank you for taking the trouble to upload it Paul. I wanted to confirm and reassure myself that the switch was faulty before ordering a new one. This can be done after the internal tailgate trim has been removed, because it's easy to access the back of the switch even before removing the chrome trim. All you have to do is find the back of the switch, and pull off the little plug from it, shown later in your video. There are two wires coming from the the plug. Mine had a black and a yellow wire. Shorting these two together with a jumping link caused a clunk and the lock opened. _Not_ the plug with three wires, that one is for the boot lock solenoid. Being me, I had to investigate what the problem had been with the switch. I removed the flexible boot held in place by some clips and some sealant which had dried out, scraped away the potting compound, and there is a tiny little crappy pushbutton switch embedded inside the assembly. This has a little dome which collapses when you push it to make contact. It was just a little bit corroded. I was going to try to clean it, but one of the legs snapped off so I can't say whether or not that would have worked.
@@PaulsTechChannel I have done a temporary bodge with a small toggle switch, while I wait for a cheap Ebay replacement to come from China; £3.81 including postage. I just kept the 2-pin plug, used the existing tails of the wires from the plug, soldered the toggle switch onto them and insulated the connections to make sure they don't short to the metal bodywork. It will do fine for now.
A great video, just about to trade my Insignia in when the boot catch failed. Thankfully I came across your video and got the issue fixed very quickly. Many thanks for sharing
Thanks for the video. It was really helpful. I had to pay the price in blood as when I removed the door stop caps, the screwdriver went straight into my hand ✋️. All the best!
I used to pop out the switch cut off the microswitch part & short the 2 wires together & hey presto boot open no need to climb in back or clear out people's junk.
This ok on a insignia, up to 11 plate maybe 12 or 13 , but from 14 onwards it is totally different,, There are 7 bolts, all 7 m, it is slightly different and a little more involved from a 14 plate onwards,,
Wow..... Is this procedure the same for the estate version? Ours has an electric tailgate that goes all the way up/down. It's been temperamental for about a year and recently its just stopped working and wouldn't open ar all. Is the estate version designed the same as the sedan?
Great video?thanjs?couple or random questions,that gun is it 1/2 inch with adapter for smaller bolts,and where did you get that huge canopy that car is under?it’s great
I believe he has the plastic cover off in the video. It also threw me. If you look very closely inside the boot where the lid meets the bumper, you can get a screw driver in there to release the catch.
is the same switch for all opel insignia? I have a combi 2013. can you give us the link with the web site where we can find it or the part number. thank you
So slightly different screw layout on my 2017 insignia 7 in total ( 6 in a straight line and 1 in centre by logo ) and two white things ( which I've no idea how th get off so I just pulled at them and they come through undamaged unfortunately for me after replacing switch my boot still won open 🫣
![[ TEASER ] เงาะป่า - วงL.กฮ. | TMG RECORD](http://i.ytimg.com/vi/M4ObdFfcPww/mqdefault.jpg)
Worked for me. Very helpful, especially showing how to open it from inside as I don't have the button on my key. Thanks.
Glad it helped
Just used this to change mine (21/07/23) and it went as flawlessly as within the video. Thanks for the great direction. Excellent work
Thankyou, Glad it helped!
This is a very helpful video and made the job of changing the boot lid switch itself quite easy to carry out. I had more of an issue with emptying the boot
Thank you
Night Hawk
Glad it helped
I've just finished replacing my wife's car boot switch using your excellent video. I can't thank you enough for sharing this. 🙏🙏🙏
Glad it helped!
Thank you for the very clear instructions. The hardest bits were getting the plastic cover off the lock and putting the felted plastic part on at the end. Job done!
You're welcome!
This is a wonderful video. Thank you for taking the trouble to upload it Paul. I wanted to confirm and reassure myself that the switch was faulty before ordering a new one. This can be done after the internal tailgate trim has been removed, because it's easy to access the back of the switch even before removing the chrome trim. All you have to do is find the back of the switch, and pull off the little plug from it, shown later in your video. There are two wires coming from the the plug. Mine had a black and a yellow wire. Shorting these two together with a jumping link caused a clunk and the lock opened. _Not_ the plug with three wires, that one is for the boot lock solenoid. Being me, I had to investigate what the problem had been with the switch. I removed the flexible boot held in place by some clips and some sealant which had dried out, scraped away the potting compound, and there is a tiny little crappy pushbutton switch embedded inside the assembly. This has a little dome which collapses when you push it to make contact. It was just a little bit corroded. I was going to try to clean it, but one of the legs snapped off so I can't say whether or not that would have worked.
You're Welcome :)
@@PaulsTechChannel I have done a temporary bodge with a small toggle switch, while I wait for a cheap Ebay replacement to come from China; £3.81 including postage. I just kept the 2-pin plug, used the existing tails of the wires from the plug, soldered the toggle switch onto them and insulated the connections to make sure they don't short to the metal bodywork. It will do fine for now.
Just done our two Insignias using this tutorial. Went near enough perfectly. Thank you for your help.
Glad it helped!
A great video, just about to trade my Insignia in when the boot catch failed. Thankfully I came across your video and got the issue fixed very quickly. Many thanks for sharing
Glad it helped
Great video. Followed the steps easily and replaced my boot release switch in under 20 minutes. Thanks for uploading.
You're welcome!
Thanks for the video. It was really helpful. I had to pay the price in blood as when I removed the door stop caps, the screwdriver went straight into my hand ✋️. All the best!
Great guide. The hardest bit was getting the latch cover off... I couldn't, so had to slide the boot hatch liner over it.
Glad it helped
Thank you so much for putting this video on. You made it look really simple, and it was! Just did mine step by step. Much appreciated!
You're welcome!
Worked great easy job on my vauxhall Insignia
Great video mate ,saved a trip to garage . Wonder how much a garage would charge for this job .
Thank you so much this video has been a massive help for me and save me a lot of time and stress
You're very welcome!
Thanks, that has answered so many questions.
Glad it was helpful!
I used to pop out the switch cut off the microswitch part & short the 2 wires together & hey presto boot open no need to climb in back or clear out people's junk.
Thanks for this video. I fit the switch with no issues after watching this
No problem 👍
Great video. I
rReplaced the switch, and the latch, but now I keep getting a boot lid open warning even though everything is working fine
Check micro switch in boot latch.
@@PaulsTechChannel Thank you. What / where is that?
@@craigdunne1236 It's inside the bool latch itself.
short and to the point, great instruction, thanks a lot !!! dziękuję !!!
You're welcome!
Extremely helpful, thanks!
You're welcome!
Thnx for great description of this job. 😊
Most welcome 😊
Cheers for this. Done in no time. 👌🏼
No problem 👍
Thank you just did mine video really helpful.
You're Welcome
Very well explained thanks paul
Very welcome
Very handy video great guide
Glad it was helpful!
Brill cheers matey
This ok on a insignia, up to 11 plate maybe 12 or 13 , but from 14 onwards it is totally different,,
There are 7 bolts, all 7 m, it is slightly different and a little more involved from a 14 plate onwards,,
Great video thank you. Is that the same button for a Vauxhall cascada keep op the great work
Very helpful, thank you!
You're welcome!
Hi, brilliantly explained. Would you post the link to the eBay seller please...
www.ebay.co.uk/itm/OEM-VAUXHALL-INSIGNIA-HATCH-SALOON-TAILGATE-BOOT-OPENING-SWITCH-13422268-NEW/152490828140?epid=17039400759&hash=item238129616c:g:~gIAAOSwdGFY3LiW
Wow..... Is this procedure the same for the estate version? Ours has an electric tailgate that goes all the way up/down. It's been temperamental for about a year and recently its just stopped working and wouldn't open ar all.
Is the estate version designed the same as the sedan?
Hi great video, replaced and working. Only thing is it sounds a bit clunky when I open it, any ideas??
Great video?thanjs?couple or random questions,that gun is it 1/2 inch with adapter for smaller bolts,and where did you get that huge canopy that car is under?it’s great
Impact gun I use for smalller bolts is 1/4" Milwaukee M18BID. Canopy is available here - eBay item number 110709281698, size is 10 feet x 20 feet.
Brilliant thank you
You're very welcome
I’ve done this twice and it always stops working after a few weeks. Any ideas?
very helpful, thx
Glad it helped!
Buen video, de gran ayuda.
Gracias
Must be a common problem with insignia boot switches I just had to fold seats to open mine.
Is the switch the same for 2015 sports tourer?
I changed the switch like the video shows great video, but the boot still won't open any ideas??
Possibly the lock assembly itself is faulty
This would be helpful but the inside of my vehicle bears no resemblance to the video. I cannot locate anything that looks like a'boot release catch'
I believe he has the plastic cover off in the video. It also threw me. If you look very closely inside the boot where the lid meets the bumper, you can get a screw driver in there to release the catch.
Wish removing it on a Tourer would be as easy as on yours :c
Iv done all that replaced new switch it worked twice then not work anymore
👍👍👍
Is it the same on a tourer please
Yes it is.
is the same switch for all opel insignia? I have a combi 2013. can you give us the link with the web site where we can find it or the part number. thank you
Nothing like my Vauxhall insignia
Insignua boot lid
So slightly different screw layout on my 2017 insignia 7 in total ( 6 in a straight line and 1 in centre by logo ) and two white things ( which I've no idea how th get off so I just pulled at them and they come through undamaged unfortunately for me after replacing switch my boot still won open 🫣