ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก
Is A Nissan 370z Faster Than A Mach 1 Mustang? Import vs. Domestic 0-60 Challenge!
ฝัง
- เผยแพร่เมื่อ 18 ม.ค. 2020
- In this video we put a Nissan 370z up against a Mustang Mach 1, in a 0-60 challenge. We had a great time making this video, hope you enjoy it!!
#sandrmotoring #mustangmach1 #nissan370z
LINKS:
Subscribe to Chris Sossong:
/ @thejdmguy101
Event Page:
www.facebook.c...
Darlington Dragstrip:
racedarlingtond...
PODCAST:
anchor.fm/S%26...
MERCH
www.sandrmotori...
SOCIAL MEDIA
/ scottandrandallmotoring
/ sandrmotoring
/ sandrmotoring
PATREON
/ sandrmotoring
FOR BUSINESS INQUIRIES:
sandrmotoring@gmail.com
The Mach 1 mustang was originally designed to be the new 2003 cobra.....the engine uses navigator cams for extra torque and uses the the same heads as the cobra terminator........it was rated at 305hp by Ford but it was faster than the 99-2001 cobras that were rated at 320Hp.......my personal opinion......The Mach makes more than 320hp but Ford underrated it at 305 because they did not want it to bite them in the ass like the major recall they had with the 99 Cobra being under powerd from there factory numbers
Manual Mach 1s likely made 335hp/350tq compared to the 320hp/317tq rating the cobras had. Just my guess from what I have seen on the dyno and assuming 15/16% loss.
Dino Crazyy I can assure you a stock Mach 1 doesn’t make close to 350whp. 1st and 2nd gen coyotes make about 350whp. My 2v mustang can run with a Mach 1 and it made 260 crank horsepower out of the factory
@@creepystank420 im talking about at the crank not to the wheels bro... my car bone stock dynoed 291/313 to the wheels. so simple math suggests the car makes over 330/350 at the crank. and thats 350 ft lbs not hp.... after an x pipe and tune the car made 309/328 to the wheels.
@@creepystank420 also your 2v is not running with a mach 1 unless you have better tires then the mach 1 or youve raced an incompetent driver.
@@creepystank420 Even if you argue dyno jet and mustang dyno that would mean my car would have made 272/288 which is still roughly 320/340 at the crank. the whole point is the mach 1 was in fact underrated. your 2v is overrated
definitely need a driver with more seat time in the mach1, with 3.90s and full exhaust i'm at 60mph top of 2nd/ bottom of 3rd, when the ass-end starts to walk , feather the throttle and shift to 3rd. the mach1's start pulling real hard in 3rd
You’re right on the dot with that! I also own a 03 Oxford white Mach 1 and it pulls hard as fuck in 3rd gear,my Mach 1 is also bone stock down to the air filter
The 4.6l 4v mach 1 was definitely underrated it made more than it was rated from the factory which was 305 hp when they dynoed stock at 300 whp which is around 350 crank hp
You guys are silly as hell. Over 7 1/2 seconds for a mustang with a 5.2 0 to 60 and the Z below 5 seconds. Im a firm believer in racing at the track. 2 cars and 2 driver, but no race of the cars side by side. Yeah...you guys should be baking cookies or something. Let your father man his own machine.
Thank you for the kind words.
Mach all day long! Gotta love the rumble from the 4.6 dohc👍👍
It shouldn’t even be close guys. Really need some practice launching and shifting. That car with the setup should be in the mid 5’s. Why not do 10 runs on each, get practice in.
0:58 lol when ya gotta go ya gotta go!
I honestly like them both a lot. I've got a soft spot for Mustangs. Had 5 of them, 3 Foxbodys and 2 SN95's
Hahaha he really did go pee in the bushes. I'm definitely a closet mustang fan. They have mustang week here in Myrtle Beach every year in Sept. I think I might have go this year.
That was a bad,slow take off. Also i have an 04 screaming yellow mach 1 with 4.10, i know its faster on take off than what yall did.
k chad
Who was driving the stang Mr Magoo?
im a lucky poor man i have both and i love them both but i dont drive mach 1 in rain cool video guys
I've actually raced one of these in my 2004 Orange 5 speed Mach 1 and I blew his doors off. It was a "Nismo" edition as well. Wasn't even close btw.
Love Stangs I’ll choose em over any car 💯🐎
Jesus I hate being that guy but y'all need to learn how to drive😭 think of the shifting as one action as opposed to three seperate moves. Push (pull) the stick as youre going for the clutch and keep your foot planted. Awesome vid man🔥
Yea.. they need driver mod asap, 😏
Glad I'm not the only one that thought those shifts were pretty bad lol 😂
Always some negative POS crying in the comments.
Great video.
The Mach 1 is always fun.
just in time in the mustang he got to 60 befor he had the opportunity to miss 3rd hahahaha
Also remember the mach 1 is also 5 years older.
2004 mach 1. Badge and brighter yellow give it away
Something is off here i had a 1998 Mercedes E430 and it was doing 0-60 in 6.8 and that was using a draggy so it was accurate.
That’s a horrible 0-60 time for the 370Z. They can get to 60 in just under 5 seconds.
Yea I bogged it pretty bad.
Terminator block is iron and has forged internals.
The Mach 1 and the previous N/A Cobra have an aluminum block and not forged internals.
All cobras and 5 speed machs had forged cranks but prior to 03 the 4v didn't have forged rods and pistons.
Which was faster? Hint: they both went 60, so they went equally fast. But one was quicker.
I have beat a couple 370Z’s in my Mach 1. The 370Z is a pretty good car considering it’s a V6.
Mach 1 needs better tires and 100% a better driver, my grandma can shift faster than that🤣
Are you serious? I'd beat them in my svt focus. If they are driving that slow
7.3 is though, I don’t feel so bad doing 5 flat in my V6 Challenger. 😂 we bought part of SLO gang
7.66 seconds 0-60 ??!! Does it have a burnt out cylinder ?? That’s a shit 0-60 time … One would expect it bare-minimum to AT LEAST be in the low 6’s …..
Learn to shift
great video
Ignorance is bliss.
"This Z has what 325-350".WTF?? And this guy is a car guy???? Know ur specs before making a vid
Shift faster
0-60 determines quickness
0-160 determines who is faster
That was fun! Is your dad allowed to watch supRANDAL? I only tried it once in the EcoBoost, got a 6.3 0-60.
Yes it was! He doesn't have much interest in anything without a V8. That was the second time I'd driven the car but the wheelspin was crazy
What wheels are those??
The stock 03-04 Mach 1’s would beat the 03-04 Cobras in the 1/4 mile I raced half a dozen stock Cobras at the Dragway and never lost, the Cobras were always closing on me into the traps but never caught me.
Stick shift Mach 1’s had the forged 8 bolt cranks.
You were racing very bad drivers my friend lol. The best time I ever seen for a Mach stock was 13.1 at 105 that is stock down to the tires. Same driver same drag strip (evan Smith at Englishtown) the cobra went like 12.40 at 113 or something like that. There is a huge gap. If you were holding them off all the way through the quarter they was getting extremely bad starts and prob shifting like shit to boot. I love machs but they won't touch a terminator stock for stock equal drivers. A fbo geared Mach can Def take out a stock terminator which is fairly impressive.
You were racing very bad drivers my friend lol. The best time I ever seen for a Mach stock was 13.1 at 105 that is stock down to the tires. Same driver same drag strip (evan Smith at Englishtown) the cobra went like 12.40 at 113 or something like that. There is a huge gap. If you were holding them off all the way through the quarter they was getting extremely bad starts and prob shifting like shit to boot. I love machs but they won't touch a terminator stock for stock equal drivers. A fbo geared Mach can Def take out a stock terminator which is fairly impressive.
@@midnight347 I agree with that statement about the drivers capiib
Capabilities, stock trim my Mach 1 was right around your 13.teens after 4:30 gears, headers and a good tune I was in the 12:80’s.
I raced with a couple guys who were running in the factory stock class and were constantly running low 12 second passes the one guy finished 2 or third that year and actually ran an 11:90 something for his best ET.
My mach is so much faster...tf. but its got 410s.
I'm sure if we had a clue on what we were doing, the results would have been different lol!!
Very inaccurate testing.
Fastest stock 0-60 I've ever heard of in a mach was 4.9, and 12.9 in the quarter. The quarter mile pass is here on YT, twas a young fellow. I just gave my 03' to my niece.
I was able to get 4.8 and I never took it down the track
Or granny shift with a damn shirt shifter lol.. I have a 03 with less bolt ones and get a quicker 0-60 lol
I get into low 6s and high 5s in a stock gt I'm not sure what's going on in this video lol
My maxima is faster than my mach 1 or my mach's speedo can't keep pace with the acceleration one. I've run them both to a fixed point on a road, the maxima is at 80 to the mach's 75. Kind of shitty considering two less cylinders and 1.1 liters smaller but the mach wins the cool factor award at least.
Even an auto Mach 1 of those years is gonna be faster than your Maxima. But to each is own!
Bad launch/shift drive the car a good bit you’ll get it down a whole heck of a lot faster than that
VQ powa!
Oh yea! If I didn't bog the launch the time would have been a lot better.
I don't know if we can be friends.....you said you like mustang's....🤮
Now the supra doesn't stand a chance!
Wish both of you had a chance to ride n my red car at full power.....think Randall's face times 10 !
I've ridden in a couple other Mustangs but they weren't as rowdy as that one.
I guess you will have to build another one and let us ride in it 😉.
I can't wait to hook up that maf-t and isc, I'm ready to turn my car up!