How To (2K Clear) Over (Rust-oleum Turbo Spray Paint) With Professional Results!!!
ฝัง
- เผยแพร่เมื่อ 1 ต.ค. 2024
- In this video I share all the tips and tricks on how to spray 2k clear over @RustOleumBrands @RustOleumAutomotive turbo spray paint. This 2k clear makes your turbo spray paint last for years and also deepens the shine. Another cool feature of using this catalyzed clear is that you can wet sand and buff it to a show car finish and it makes it chemical and gas resistant. This was a fun video that I learned a great deal about how this spray paint stuff works and any one can do this!! Ill drop all the amazon affiliate links below so yall can check the items out ,and if you purchase off these links it helps the channel out at no additional cost to you. I make a very small percentage off of qualified purchases.
Paint Shaker 4000 Video Link • Build your own FREE (S...
Links Below
My Website to buy Shirts www.acdesignsgarage.com
My PO Box Below:
PO Box #782 Troutman NC 28166
Instagram @ACDesignsGarage
Video where I hurt my hand.
• I Cant Believe This HA...
How to spray paint your car, turbo can video • SPRAY Paint Your Car (...
How to cut and buff spray paint video
• (SPRAY PAINT) Your Car...
Links Below
Spray Max 2K Clear 3 pack amzn.to/3K5fS0v
Spray Max 2K Clear Single can amzn.to/3yjHhcu
Rust-oleum turbo can amzn.to/3UBsYbZ
Mineral spirts amzn.to/3WO0wFy
Motor guard soft sanding block amzn.to/4bdyCHf
3M rubber squeegee amzn.to/44KPeDE
600 grit wet dry sand paper amzn.to/4apEoEn
18 inch masking paper amzn.to/3UDV2KI
3m Mask amzn.to/4a0zrmk
Soft sander Foam block amzn.to/39mAToD
water spray bottle amzn.to/39j2O8L
233 tape amzn.to/3FMISHB
scott shop towels amzn.to/3Pjox0N
micro fiber towel amzn.to/3wgg9YF
Dura Block Sanding Block amzn.to/3JIJXCX
foam sanding blocks amzn.to/3FIYgoc
Sprayway Glass Cleaner amzn.to/44q4ntY
Wax and grease remover amzn.to/4bq4Zmi
Hey bud you can put that leftover 2K Clear in the freezer & when you're ready to use it again just put it in warm water for a few minutes it'll work like new
Neato, never heard of that! 👍
Awesome thank you for the tip!!!
That's new
Bro is from the future
Wait REALLY?!?
OMG That's great! I just bought a 6pk of those to do my Hubby's tractor and it's been heck trying to time the opening of the can with the weather. They arent cheap so I've been frustrated trying to use it all before it rains or gets windy or cold or too hot. 😂
I'll try this and see how it does.
Thank you!
Everyone should be hitting that like button and sharing. He has spent good hard money for all of us to watch and learn. Great job and keep up the great videos! I really enjoy watching your videos. Your a great TH-camr!!
Thank you very much for the kind words!!!! I love helping people to learn paint and body, and also seeing them happy when they turn out there first paint job!¡!
@ACDesignsGarage I painted a whole 96 chevy long bed doing exactly what you've done here. Then I cut it and buffed it. It looks unbelievably good. If you do a cutting video on that 2k clear a lot of people are gonna be shocked. 99.9% of people wouldn't know my paint job wasn't factory. Came out WAY better than I had hoped for
@@ACDesignsGarage😅😅😅😅😅😅66
If you do it again, wet sand, the black before you add the clear and then wet sand, the clear after that
I thought about that for another video, you think people would be interested?
I would be interested . I’m in the process of doing that now , day 3 of the turbo drying
What kind of difference will sanding the black before putting on the clear do? Make it have a more mirror like finish?
@@ACDesignsGarage i would be really interested in seeing that process im trying to rattle can my hood of my car. i want to get good results
If you're going to paint outside wait till right after a rain storm. It settles all dust and dirt from the air and the bugs are busy hiding. Always have my best results after everything as been wet down
should you wet sand down orange peel before spraying clear coat? ive always wondered that
You can but you'll have to wait a few days, if you do it this way you can do it all in one day. This weeks video I cut and buffed the clear and it turned out amazing! It goes live on the 24th at 8 pm est.
I wish that company would make a similar professional paint gun that would screw on the top of that spray paint can. I think a company would double their stocks overnight. Imagine just order your color of your vehicle and no air compressor needed.
Your right!!!!!
It's amazing that you can do that with the Turbo Rustoleum and 2K Clear. Waiting for the follow up to how well the 2K holds up over Rustoleum.
It's a month and counting and still lookin good!!!!
Aye that looks a lot better. Let it dry for a week, and wet sand. Then cut/buff it will turn out clean. I’m tempted to paint a truck like this with the turbo can and some 2k clear.
Is there a reason why you have to let it sit for a week before sanding? I thought this stuff hardens after a few hours
@@brandonhoud42just let it fully harden 100% before even sanding
If you wet sanded the black down flat before the clear it would have been like glass
Your right, I only had one day due to rain lol
What about wet sanding before the clear?
Yes that will do a awesome job, may do another video on that!!
@@ACDesignsGarageplease make a video sanding the rustoleum then adding 2k clear after.
You have a great spray technique. How many total cans of 2K clear did you use on that panel? I ask, because I am trying to calculate what I would need for my own car.
Thank you!!! I used 2 cans of the spraymax 2k clear. You may be able to skimp a little if you can get the base a lil slicker and not as much orange peel.
Looking forward to seeing how it finishes up! Yep, I'd like to see how well the adjustable nozzle spray cans work. I'm looking to do an old garden tractor for my first try.
I'm going to shoot some videos on the adjustable tip cans soon!!!
I would love to see you paint the truck with a rattle can me and my son are working on a 1966 C10 truck are next step will be getting it ready for paint but as we know paint job are expensive I was thinking about Rattle can Spraying I think I can get a good enough paint job for it to look good thank you for the great contents
That's awesome. I have a 65 c10 I've been workin on. The spray paint is cheaper but if you have a spray gun and a compressor it's so much easier!!!!
@@ACDesignsGarage I do have a spray gun from harbor freight and a compressor but I don’t no how to go about mixing the paint with the right mixture do u have a video in your playlist how to do that?
Tennessee Paint Bugs.
😂😂😂
From West to East, North to South...
Those dang TN Paint Bugs are causing us ALL to have problems!
You got that right lol
Nice job again- gives some of us rookies some hope that we can come up with a good quality result!
Thank you, you can do it, you can always sand it off lol
That stuff looks like it works great. Thanks for sharing brother
Thank brotha for all your support!!!
I really appreciate that you show the things like sanding in real time. So many videos trim those parts for attention span reasons but its so helpful to see everything in real time and get a feel for how long things take and what time windows we're really working with. If people just cut to post sanding, you don't know if it was 5 minutes or 5 hours.
Thank you, ive had a ton of complaints about taking forever, but I want people to see it's not a 2 minute job lol, thank you for watching !!!!!!!
I would like to see the 5 tip can on the tail gate with some 2k clear 58:43
Awesome ill try to film that!!! Thanks for the idea!!
I'd like to know if the 5 tip lid would work on top of the Tuebo can!
No it doesn’t work
Sweet. Beautiful job . I would roll with just like it is thank you. Love the spray can jobs thank you so much.
Thank you, there actually pretty fun to do!!
Years of experience, great value on this wonderful video.
Thank you very much!!!
I’m NC too and ran into a lot of the same problems (my first go round w the turbo/2k system) yesterday with dry spray and lots of orange peel from not going heavy enough with the clear. It wet sanded good today w 2000. Good luck man
Wish me luck, this Fridays video I'm gonna wetsand and buff the 2k lol
@@ACDesignsGarage check out this video. Specific easy fix for orange peal. Just saw today.
Seeing how the turbo cans have a lot of orange peel, can you wet sand it before doing the 2k clear??? Will that make it look even better????
Yes you just have to wait a few days till it dries totally, maybe 5 days
One big problem with doing this…. You are putting a catalyzed product which is a “thermoset” and a non catalyzed product ( rustoleum) which is a “thermoplastic “ which means that if you reintroduce a solvent to a thermoplastic it becomes liquid again… the complete opposite goes for the thermoset product .., it becomes solvent resistant after curing.
This my friend is a guaranteed peeler, by putting the product that cures over one that technically doesn’t it will trap solvent and lift the clear right off the surface.
Sure it looks good immediately but it won’t last , if you get a stone chip and then power wash your car the clear will peel off in sheets…
I’m a 35 plus year painter that has had professional training from PPG and BASF and both will tell you this is a “ No No” …
Sure you can do it, sure it works, but only very short term. Waste of time and money
But that’s my opinion, you do you and have fun repainting all this stuff, job security… more content
If u would have let the black paint dry then wet sanded it then cleared it wouldn’t b filling all the orange peel
Your right, the only reason I didn't, I had to do it all in one day due to a bunch of rain comming lol, thanks for watching!!!!!
looked good after you polished it for sure
I like the fact that you show yourself use a squeegee to dry the water off as you sand to inspect the surface for proper surface prep, Not many painters show this step to see that they have the surface prepped correctly. And in my honest opinion it is a very important step!
I try to remember everything lol but if I do miss something feel free to chime in, I'm trying to help these guys that are beginning and make it as easy as possible for them.
Should I wet sand the paint before putting on the clear if I have orange peel? Or can I put the clear over it then cut and buff the clear and it will get rid of the orange peel?
Yes you'll need to wet sand to give it a surface to bite to. I'd block it wet with 600 on a flat block and flatten it down a little then shoot 3 coats of clear then you can cut and buff it!!!
Hey, I'm gonna be spraying this coming weekend and would like to know how much time you waited for the Rustolium to dry/flash before spraying the Max 2k clear? They seem to be pretty compatible paints. I really wish I had a spray can shaker, haha
I just let it tac, get you a spot on the masking tape that you have sprayed across and touch it it should feel like the sticky side of that blue painters tape.
Wonder how long this paint job will last? Thinking about doing this to my truck
With the 2k clear id say a good many years, if it's in a garage it will last a long time
I'm appreciating this so much as I'm going to start doing bodywork on my car and refuse to spend my hard earned money and prep work to some guy who will give a terrible paint job. I'd like to do it myself for the learning experience and so I can only point the finger at myself rather than someone else on top of being out a couple thousand bucks. Thanks again
Awesome love to see people trying out this very rewarding trade!!!
Yes! So true.
My dad taught me to do things yourself. I live my life by that as much as possible. With TH-cam videos like this, we really have no excuse
I was about to ask about adding some soap, and you answered it. I feel like it keeps my paper from clogging up.
Yeah it works great and helps to clean it also!!!
Really injoying watching your videos. I'm trying to get my 2003 Dodge back to looking better than the twenty years of Texas heat, cold, and intest sun has done to the paint. The flame red/clear burned on the hood and roof. Thanks again, James in Texas.
Awesome thanks for watching James, We were just in Texas april in Austin for the Lonestar round up!!!
Can you spray paint bumpers of cars like this? I have an old 95 TA that I would like to try this on
You should be able to!!!! I love them old T/As
I think you should of wet sand the black before the 2k clear coat but it still came out amazing
Your right, I had to do it all in one day due to the rain comming lol thanks for watching!!
Is the turbo clear any good
It's basically paint with out the color I think. You need a catalyzed 2k clear so it will hold up longer in the sun.
Was the dusting of color necessary for the clear to stick? Or will the clear stick to dry paint? Thanks
Just trying to keep the peel down due to those turbo cans dumping paint lol
Rustoleum 2 part clear in a turbo can! You’ll sell thousands
I 100% agree that would be Rad!!!
How about tailgate on the 5 nozzle cans you can show us new to painting and body work guys how to get around them embossed letters with sanding at the same time. Keep'em coming. How's the hand feeling?
It's feelin better, thanks for asking, that sounds like a good video, let me see if I can dig up a good tail gate and I'll give it a shot!!!
How long do you wait from the last coat of paint till first coat of clear?
Usually I'll check a hidden area and I wait till its barly sticky, kinda like the back side of masking tape
You can buy clear lens filters or ND filters to cover your lens to protect it.
Thank you for the tip!!!
Thank you so much for taking the time to post all these videos! This is exactly what I needed to know right now because I'm just about to paint a camper shell and it's my first time painting something auto quality.
Awesome that's cool, good luck!!!
I came to TH-cam looking for exactly this video...(great job by the way) and i spotted that Mercury in the background. What's your plans for it??
Thank you, it's my brother's car, we're gonna get it running again in a video soon I hope lol
I used the best of everthing, including a booth and the clear coat came out with so much orange peel that i had to cut it with 600 and a DA before sanding it down progressively to 2500 then buff. So tools dont make the man a better painter
I agree you have to learn the process!
Another great video from you! Thanks for sharing. I'd really like to learn how to how to paint with a compressor/gun setup. I would love to see a video with you spraying a panel with a gun with recommendations for what equipment a novice would need to buy. Hope your hand is healing ok. Peace
Thank you very much, ill try to make a new one I'll put a link below to a older on that I did, hope you enjoy!!!
th-cam.com/video/fTjsSwr97So/w-d-xo.htmlsi=44BxO4FUrYSoQL_0
Question, I used a rustoleum painters touch paint + primer, my 2k clear wrinkled after first two layers. I know I could have sprayed to quickly on a base coat, but how can I get my clear coat to stop wrinkling? I understand lighter coats and flashing time I did not really pay attention to but any tips maybe I can send you a picture of my jet ski project? I'll tip you just need some help
I've hear people say if it gets to dry it will start wrinkling, Not sure if the paint plus primer is any different than the regular rustoleum like I used. I've sprayed the plane enamel rustoleum 3 times with no trouble so far. I like to spray the clear when the base color is barly sticky but no color comes off on your hand.
Harbour Freight has great 9 mil black gloves... to keep your hands clean and dry...I'm a dishwasher. They last all night.
I need some good ones
Question, do you think you could put the turbo nozzle on the 2k can, and would it function the same?
Also everyone, always remember to “wipe the tip off”!! - that’s what she said 😂 sorry I had tooo
I tried but for some reason the turbo can stuff is alot bigger than the others
I love your work and your faith. Thank you and God bless you!
Thank you very much, hope you have a Blessed day!!!
Slow down on the application, your running. Was a painter for 20+ yrs. After the first to lite second coat lay it on and pray you get no runs. It happens even with pros. But not often. Nice video,and I haven't used a can to paint a vehicle since I was a kid.
The Turbo can doesn't give that option.
It dumps paint far too hard and fast to slow down. I mean, you physically can't make it spray less - and if you move slower you'll just have worse runs.
But I agree... if you're using a different type of spray paint you should slow down.
I barly got one lil sag, lol runs don't rust lol. Thanks for watching!!!
Don't add car wash soap to your water while wet sanding before painting. Some car washes have waxes added to them like carnauba that will cause adhesion issues in the paint like fish eyes. Dawn is fine and in most cases promoted since it serves dual purpose by making the water more slick and also cleans oils off of the panel at the same time.
Your 100% correct I wish I'd of said that, Thats why I use a degreaseing soap like dawn alot of the time!!
What is your opinion on the color. The thing I didn’t like about the turbo can black as with most aerosol black paints it doesn’t look as rich deep black as say a single stage black. I’m really curios if the 2K clear changed the appearance of how deep black it looks.
I think the clear darkens it up a little bit and has a better gloss, were gonna try to cut and buff that 2k clear this week and see what we mess up lol. Black the color goes from the brown side to the blue side of The color spectrum, I think the rustoleum is on the brown side of black when you get the super black its twords the blue side of black.
Great job! Enjoyed the video! Thanks for the tips, time, and thoughts that you put into them! More welding and body & painting it’s all good! Thanks again.
Thank you for watching!!!!
I would have used the black nozzle for the clear to get a wider fan
I'm from Boston Massachusetts I understand it's a demo it's a demo 😊
not bad to say you never painted before
Can you please do a Matte Black paint job I bought my paint from the Summit here in Macon,ga I'm catching hell painting it lol I have blisters on it an now the paint is chipping so that lets me know I didn't prep it enough
I may try that in the next couple of weeks!!!
terrible video , the title is turbo spray not you talking to much
Great Job. Can't wait to see the finished result!
It turned out awesome!!!!
Just leave some spirit in the cap put the can on leave it upside down
Great idea!!!!
I painted my car with a cheap harbor freight hvac cup gun and poked a hole in spray can and let the gas seep out and poured it I. My harbor freight gun and shot it and it turned out great
That's awesome
Ok I have a few questions I painted my car with rattle cans and I have not cleared it yet I was told to wet sand before putting clear down is that correct? I have wet sanded it so I hope so and now I’m about to spray the clear will I have issues? Please lmk
Yes , if it's dry you need to sand it. Plus when you sand it it makes it smoother, you should be good!!!! I like 600 to 800 wet before I clear.
I popped the bottom of the can to mix it and it started coming
Out of the bottom ! 😢. Am I suppose to hear a click or pop or some noise to indicate that it’s mixing inside ?
Oh no!! I just push it down and hold it for 5 to 10 seconds you can tell when it's empty because the button gets easier to push. Mine never made any noise.
Just subscribed I just painted and used the 2K clear and left some drips on my tailgate surface is there away to repair without having to redo the whole tailgate
Yes its pretty easy, you take a small hard sanding block and slowly sandjust on the run till it gets flat then buff it up to a shine. I start with 800 wet then 1000 wet then 1500 wer then 2500 wet then buff. Basically you cut it flat with the 800 the the rest is removing the deeper scratches. Would you like me to make a video on it??????
Love the videos brother, keep on keeping on
Thank you very much!!!!!
Catalyzed urethane sprayed over uncured ,uncatalizd acrylic enamel (Rust-Oleum) simply will not work. The bass compounds for the two types of paint are not compatible. Incredible painter would never make a video spring something with a can in his yard... 😂
It's held up for a month so far, you have to understand not everyone has $900 spray guns ,shops and compressors. I've painted multiple 6 figure muscle cars and hotrods. I understand this is not the perfect application but you have to work with what you got lol!!!
I love your shake master what a cool invention!
Thank you they work pretty well
Heating the can helps to atomize the paint better.
I normally just youse a regular tall boy rust oleum like the way they spray better the turbo gots a bigger fan but a lot more orange peel so don’t feel it is worth it ether way I still 800 grit wet sand before put clear coat on it
Yeah I wish they would use a smaller hole in the tip of the turbo so it would cut down on the peel.
Not too shabby! Can't wait to see it cut and buffed!
Thank you, I hope it turns out SHINY!!
@@ACDesignsGarage I hope there's enough clear coat thickness, if so then it'll definitely be super shiny!!!!!
😮i. Just used this on a jeep wrangelr hard top qnd is not that greet'lots of runs and oaint dont lay down good'change itnto rustalium the one whit the 5 tios is amazing really easy tonise and the gloss is insane
Yeah I like the 5 n 1 tips alot better, the turbo is tough to use for sure
yes I like to see the 5 and 1 sprat can comparison
Well do it, thanks!!!
Opinion? Spray bombs cheaper? I want to debunk the fact that they are cheaper than spraying with a spray gun.
Alot depends on whether you have all the spray tools you need, but I will say using a spray gun is alot easier to get a nicer job. I painted that short bed with 1 turbo can and 2 cans of 2k spraymax clear and had $50.00 in it. So probably $150.00 to do a whole shorted. It's cheaper but a ton more work lol
Shit it looks like ya gonna get fit using that
TURBO CAN !
😂😂but man it’s a good product by the looks of it I got myself some of the 5n1 nozzle cans to paint my bike,especially now that I have found out it is fuel n oil resistant so that’s a bonus, it just doesn’t say so on the can
Awesome what kinda bike do you have, I use to have a softtail custom harley. I will say if you want to make it shine like crazy shoot that 2k clear over it then, man ole man is it shiny. You gave me an idea I may custom paint a sportster tank I have with just spray paint!!
@@ACDesignsGarage hey cool, I got a 2009 Fat Bob
I’m second owner but first owner in New Zealand 🇳🇿 so yeah I’m gonna paint it Antique White from rust oleum with the 5in1 nozzle
Will be good to see you do the sporty tank
Could you have wet sanded the black with 800 once it was cured to remove the peel and then hit with the clear?
Yes that would be the best way to do it. The only reason that I didn't was a storm was comming the next day lol!
You could brush the paint on and sand it smooth before clear coating and get a show room finish!
That's a great idea, I bet people would flip out lol
@@ACDesignsGarage I use rust-oleum to paint a lot of my wood trim work in my maintenance job and you would be quite surprised how smooth it goes on with a brush if you thin it down right and work from the wet edge. Of course you have to use a quality brush as well.
@@ACDesignsGarage I've also painted light poles the same way with a brush and you would never know I didn't use a spray can to paint them, Gloss Black, just as smooth as if I sprayed them!
Hey buddy good video just what I do is I I bought a large canopy and make like a portable Booth because I'm bugs will really mess your paint job
Awesome I need to do me something like that!!!!
I use patio umbrellas to provide shade. They are a lot easier to move.
So how is it looking these days? Both sides, update please 😎
The turbo with no clear is faded out and the turbo with 2k clear over it looks just as good as it did except for the grass I blew all over it lol
Thanks for the video, quick question if you prime the body will you get better results or adhesion ? New subscriber!
Thank you! The only time I would use primer is if there was some chips or the paint was flaking or peeling or over body work. As long as your painting over a good smooth surface you don't need primer. Basically if you have a problem area you need to prime it
@@ACDesignsGarage Awesome thanks! Wish the Turbo cans came in more colors, have you used the white turbo can?
Looks great for a can. In the process of painting wheels gloss black then 2k clear. Did you get any reactions with base to clear? How long for base to dry before 2k clear? Thank you. Bed liner in bed and you've got a new bed. They recommend 2k clear in a warm bucket of water for it to lay down w/o orange peel. 🍊 👍
I won't speak to how his job will react. I can speak from my novice experience with this same setup on my engine bay. I tried to follow the principle of spraying the turbo, waiting for the base to tack up and applying the 2k clear. I had a bad reaction where the clear wrinkled up with the base coat. I'm assuming it's because I didn't allow for enough of the solvent to off gas.
From my research, I've read that you should allow more time for the turbo to off gas, some say a few days to a week. But I've also come across 15-20 minutes.
I will be trying this same setup again, but I plan to give the base coat about a week to cure and then I will wet sand the peel out and clear coat that. Then cut and buff.
Again, I have very little experience with paint, I'm geared more toward the mechanical side. But I prefer to learn and do things myself. Which is why I've been enjoying his content. So, hopefully in the next video he will give better insight to reaction and solutions if it does happen.
@@Mr.Wongburger
I recently used these exact products on my hubby's tractor.
Granted, due to weather I had to wait about a week or longer between the black and the 2K clear. And I haven't had any reactions.
But I also used a "ColorShift" in between. (I used Blue to Purple from the Auto Parts store. It said "ColorShift" on top.)
I'm not sure if that made any difference or not. Just trying to help.
@@inthelandofmorethansmall7582 Thank you for the info. It's probably due to allowing the base to off gas first. The clear coat with hardener will dry much quicker than the rustoleum, this traps the solvents underneath causing the wrinkles.
Had no reaction with the rustoleum but not sure about other brands. I check a spot on tape where it over sprayed on. You want it to barly be sticky like the back side of a piece of tape. You don't want it stringing like a spider web, it's still to wet at that point. It's ready when it's early sticky like tape and youll be good to shoot the 2k. You can check my 2k video and see how sticky I show it in there. Thanks for watching!!!!
Nice one AC, amazing finish with aerosols, well done!!
Thank you very much!!!!
I use a big shop fan to keep the air moving enough to keep the bugs from flying into the paint
That would work great!!!
That's a massive spray pattern from those cans, 3 trips down the side of a truck panel. And yeah those little bugs just love the smell of fresh paint!
It's fun to use, almost comical hahaha
when spraying with a large nzzle will not comes right loll, and not enough air for so much paint that comes out, try air comp: with a 1.3 jet, air only 25 PSI, i would get some cans, then empty them, remove the air out and use the air and even cheap gun with 25 PSI try it loll,
I used rust oleum then put there 2x clear and everything wrinkled
There is a difference in 2k which is a catalyzed clear and the 2x clear im guessing is just a clear enamel like the colored rustoleum , I do know on the 2x clear you have to put it on within a hour of spraying your other coat. On the 2k I also like to put it on as soon as it tacs or within a hour also!
You amazing painter.thats amazing what you doing with a pant can
Thank you very much!!!!
Like you sa Set in the first video?You get too close.Could your so used to painting With a regular spray gun you're just way too close
U got alot of texture in the paint and the clear eveeytime i use that same clear its smooth
The clear goes down slick but that turbo can goes down like bedliner lol, ive tried heating the can, light coats, heavy coats it dont matter it's gonna be chunky hahahaha
Grate job for outside thanks for your time.
Thank you for taking the time to watch!!!
Wow nice paint job😊😊😊😊
Thank you!!!!
Raid yard gaurd walk around what you're painting while spraying helps keep the bugs away
Awesome thank you for the tip, ill have to try that!!!
Guys remember safety for 2K clear coat its not your normal clear coat it has isocyanates super dangerous up in Canada air supply is require and full body suit and hand cloves since isocyanates are absorbed by your skin and liver
Get some motip caps for the spray cans.
You also can reuse the spraymax caps you can clean them if you put them on a can of brake cleaner when your done spraying the clear.
Thanks for the tip!!!
Awesome video If I was to try this out I would slowly spray this clear into a paint gun and clear something just to see how it would lay out
Hold up... can you do that?
I don't have a Paint Gun yet but I've been wondering if that was possible!
You can do that, the only problem you may have is it being pretty thin. But if you give it a shot let me know how it goes!!!
Could you just use a red scotch bright pad for prep if the paint is in good shape and you're just going for a color change instead of wet sand? Thanks
Yes you can, it works great!!!!
@@ACDesignsGarage thanks my surface is perfect no orange peel or scratches I just want it to stick
@@ACDesignsGarage I'm just trying to color match a OEM rear spoiler on my 2016 Ford focus St and it's Kona blue I've found the paint from a local supplier and they will put it in a spray can and I'm going to try the 2k clear on it hopefully it goes on even and flows out well the spoiler has a lot of contours and two air slits so it will be tough to sand and buff but I have the stuff to do it if need be love the video looks great for a rattle can I hope I can get the same results I don't want to buy a quart of the paint hardner and clear it's crazy how much they want these days for paint but I'm sure you know that lol thanks again 😎🇺🇸
I say find another hobby my friend no offense. Nice job on the edit
Thanks for watching!
Way to less paint on it.
Have you investigated a spray paint product line called, "Car-Rep" out of Finland? All of their spray line is 2k, no mixing! If your going to do that Suburban, may want to consider using that product?!
No but thank you for the tip I'll look into it!!!
Try their 5-in-1 version of Stops Rust with a rotating dial featuring 5 different spray patterns Vert. Fan, Horiz. Fan, light round, Std Round, and Heavy Round.
I love the 5 way tips!!!
Use a hose clamp with a wing nut end 😂
Yeah I've upgraded to them lol, they work great!!!
I have watched a lot of painting videos as I'm new to this and you are hands down the best on detail and common sense delivery, many thanks for your videos! I do have a question that, as usual, can't get a straight answer on reading and watching videos. I had to walk away from my basecoat project about a week ago before clearcoating it. How do I prep the dried basecoat before clearing it? I've read scuff it first with anything from 600 to 1200 grit sandpaper, then recoating it, then clearing it. What is the process you recommend? Thanks, a fellow Tar Heel.
Thank you for watching, yes your right I would stuff it with 600 to 800 grit wet then I would blow a coat of base back over it, but if you can't base it scuff it lightly with 600 grit, wipe it down and clear it.
They should make a tip that twists into adjusting a small or larger fan pattern I'm sure they can do that.
I’ve had really good luck with those cans of 2k doing mirrors, rocker moundings door handles what not.. I always have better luck with spraying big panels with a gun and some nason 2k clear, thicker build and just simply easier to control your spray. Some people say that clear is a little yellow but it looks fine for me. Your bedside turned out pretty good though I gotta say
That 2k in the can is amazing!!!Ill agree, I ve painted cars for 20 plus years and your right, a good gun and some high solid clear is way easier lol. I like the Jason stuff, for the money it's hard to beat!!