How to Replace Lower Ball Joints 2005-2015 Toyota Tacoma

Buy Now!
New Ball Joint from 1AAuto.com 1aau.to/ib/1ASBJ00318
This video shows you how to install new, quality TRQ ball joints on your 2005-2015 Toyota Tacoma. Car and truck suspensions combine a number of moving parts for safe and stable handling. The ball joint is the crucial moving component that ties those parts together. The ball-in-socket joint can wear out and loosen over time. Or, the rubber protective boot can tear, allowing contaminants to seize the joint. Bad ball joints are a common failure point on vehicle inspections because they lead to unsafe driving conditions. Fortunately, they are relatively easy to replace with the right know-how.
This repair was done on a 2010 Toyota Tacoma Base 2.7L Standard Cab Pickup 2-Door 4WD Manual and the process should be similar on the following vehicles:
2005 Toyota Tacoma
2006 Toyota Tacoma
2007 Toyota Tacoma
2008 Toyota Tacoma
2009 Toyota Tacoma
2010 Toyota Tacoma
2011 Toyota Tacoma
2012 Toyota Tacoma
2013 Toyota Tacoma
2014 Toyota Tacoma
2015 Toyota Tacoma
Tools you will need:
• Flat Blade Screwdriver 1aau.to/obHR/1AXAA00013
• Pry Bar 1aau.to/o9P/1AXAA00020
• 17mm Socket 1aau.to/ocai/1AXAA00015
• 19mm Socket
• 21mm Socket
• 35mm Socket 1aau.to/oax/1AAST00005
• Ball Joint Press
• Pickle Fork
• Locking Pliers 1aau.to/oo5/1AXAA00139
• Pliers
• Snap Ring Pliers
• 1/2 Inch Impact Gun 1aau.to/oyJ/1AXAA00252
• 3/8 Inch Impact Gun
• Ratchet 1aau.to/ocbH/1AXAA00016
• Torque Wrench 1aau.to/obdB/1AXAA00044
• Cloth Rags 1aau.to/oP5/1AXSS00035
• Cotter Pin
• Gloves 1aau.to/obaj/1AXSS00048
• Safety Glasses
• White Grease
• Chisel 1aau.to/onk/1AXAA00055
• Floor Jack 1aau.to/oay7/1AXAA00068
• Hammer
• Jack Stands 1aau.to/oakU/1AXAA00065
• Large C-Clamp
• Large Hammer
• Punch
• Ratchet Strap
• Rubber Mallet
• Wheel Chocks
• Wire Brush 1aau.to/oyx/1AXAA00079
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money

[@kevinbliss6725]

What size ball joint press is that and where do you get one? Autozone and Advance Auto don’t have the right size with their loaner tool sets

[@richardworks481]

How much money for that exact job ?

[@gregorylopez6024]

Ball joints with zerk fittings will allow you to grease the ball joints thus lasting longer. Also, you shouldn’t cut off the cotter pins ends.

[@erniesanchez79]

So I have a question so you don’t have to grease up the ball joint ?

[@Onlystocks1980]

You don’t have to remove the axle nut to do this job