-Gino’s Garage- Part 2 1977 Wanderlodge FC Injection Pump and Air Compressor Replacement

[@fernandomeneses441]

Hey Man, Thats great, a good job. I'm from Brazil, today I worked in a CAT 3208 apply in a waterpump of supermarket . thanks for share your experience.

[@henrygerrets8199]

Great video, thanks

[@Dominolittle]

Great share. 😊

[@bryandailey4174]

Thanks for the video - working through this on my bird.

[@GinosGarageUSA]

Thanks, I am following along on the WOG.

[@timeparmenter4816]

Another fine video and fix.

[@GinosGarageUSA]

Thanks for watching Tim. Hope things are good for you and the family!

[@hydromakers]

Got to pull one off nest week Just taking a refresher coarse.Thanks

[@mykemech]

Thank you for the help so far. I have a last question (easy question): Do you recommend filling the pump manually then buttoning it up or just using the primer? My primer is in a tight spot and it seems like I'd have to pump it a lot.

[@GinosGarageUSA]

@@mykemech I would add an electric flow through pusher pump in the fuel line and use that for priming. You can connect it to the ignition circuit to run anytime the engine is running or you can just use it when you are priming, but it has to be a flow through pump or it will block the fuel when it quits running of it’s not. I recommend Facet brand fuel pumps, you can get them from Pegasus racing website.

[@mykemech]

@GinosGarageUSA Thank ya!

[@chrishuelskoetter6475]

I need help please with finding the puller and bolts needed to pull that front timing gear off, with the 2 little bolts.

[@GinosGarageUSA]

There are a couple different tools that can be used for this. This is a possible option, but cannot say for sure it will work but it’s not too expensive:
a.co/d/9jVef4e
You may need to get bolts but they are standard 1/4”x20tpi bolts that you can get from any hardware store. I would recommend grade 5 or better.
This is the tool that I have:
www.apexinds.com/tools/M10070.html?gclid=CjwKCAjwgdayBhBQEiwAXhMxtkzytxrjqQRx8xHBU_vEnn2DxPZEqf7DMdpuQ7TeMiUYuE21a0K7cBoCJFUQAvD_BwE

[@0505abab]

Great video I have one of those tubes leaking I have a new pump now I need to find someone to install it in a motorhome

[@0505abab]

I've been reading my book on it I think you make it look easier than it is but still well done

[@jonnyindianajd]

What motorhome do you have, we have an 86 Foretravel Grand Villa, needs a pump or something, just stopped running, thing pops with ether.

[@Junkyarddiesel]

Is the pump timing pin anything special or did you just find something that fit

[@GinosGarageUSA]

There is a special tool for the job but you can use a 1/4” drill bit or any 1/4” round stock for the pin.

[@CanadianPenguin_]

that pump manages to look massive and tiny at the same time. how long and wide is that pump?

[@GinosGarageUSA]

I can tell you they are quite heavy. I would say they are approximately 12" x 12"

[@mykemech]

Hi! Can you tell me where I can find a governor throttle shaft seal and bushing for a 3208 Gov/pump? The internet knows nothing... THANK YOU

[@GinosGarageUSA]

@@mykemech I would suggest going to Cat with your engine serial number and arrangement number, found on the rocker cover tag.

[@mykemech]

@GinosGarageUSA Thanks. My tag is gone🤔

[@GinosGarageUSA]

@@mykemech What is this engine in, is this a Wanderlodge? If so then what year?

[@mykemech]

@GinosGarageUSA appears to be an 83 eng8ne in a 75 ford box truck

[@GinosGarageUSA]

@@mykemech Is it turbocharged?

[@hrios80]

Where did you find that gear pulled to separate the pump ?

[@GinosGarageUSA]

Check out eBay:
rover.ebay.com/rover/0/0/99?loc=https%3A%2F%2Fwww.ebay.com%2Fp%2F1133979573

[@micko7927]

What is the valve clearance in millimeters?

[@GinosGarageUSA]

Intake is 0.38mm and exhaust is 0.64mm.

[@micko7927]

Thanks mate👍