Hitachi EX5600-7 ultra-large hydraulic backhoe excavator has an acces door, maybe your excavator has a tiny one too. Send in your smallest employee he can weld from the inside for extra strenght. Have a nice weekend 😊
The first hub that was difficult to remove. If u heat the hub directly over the keyway. It will come off much easier. So heat the entire hub, then while trying to remove focus the heat at the keyway. 20 years+ experience in heavy equipment.
when you put that yellow coupling back on heat it up to about 300 degree and then it will have expanded by 0.00000654 inches per degree. Calculate .00000654 times 6 inches times 200 degrees hotter than workshop temp = .007 or seven thousands expansion. If workshop is 70 degrees then heating the coupling to 400 degrees would make its bore expand by 11 thou and it would just slide on.
Охренеть, сварщик 😅😅😅без маски,в очках варит ...😊шо будет с его рожей, кожей,глазами??я сам сварщик с 30ти летним стажем работы в теплосети.да ,охренеть ты мужик себя ненавидиш.
I think the gearbox is a copy of a Fuller-Traylor unit. I am actually watching this as prep in-case we have to rebuild ours... If you are using units like this, make sure the oil is THICK. Don't try using low viscosity oil or you'll be getting some new and exciting growls from it.
Oh you're "that guy" Maybe you can upload your videos to your channel so all the experts can leave their opinions about your work. I hope you cheer up and life gets better for you soon ⛳
Just a bit of grease on one end of the rollers. Grease is expensive. It will not be re-greased until it seizes up again. Even the silicone sealant, they only put a bit near the center. The gears do not seem lubricated very much. They did not clean the mating surfaces of the two halves before bolting them together and machining, there is dirt in between them. The shop is a mess. Junk everywhere on the floor. A mountain of chips sitting in the middle.
Easy to be a critic but this job was difficult.Well done overcoming the challenges but the floor should be kept clear before an accident happens,we’ll done workers….
A few days ago, we copied a cast-iron welding procedure from one of these videos (pile of burning charcoal, borax, gas-welding with cast-iron filler material). Worked great despite us not being able to find the safety sandals or robes for the job. We also deviated from procedure by using a dead wheel-barrow shell as the basis for the furnace.
There is a reason to use a proper sized key-way instead of a bolt. It helps keep things aligned under load so as not to cause the damage these guys have just spend days fixing.
И что же у него по пизде пошло? Отверстия не разбиты! Подшипники на месте! А вы промахнулись с посадочным под подшипник. Ну бывает и такое.он бы еще поработал. У вас ремонт ради контента.
подшипник провернуло в корпусе, размер ушел. А подшипник заклинило от нагрева, тк там нет смазки. Отверстия под централизованную смазку заткнуты. Слесарь рукой набивал пластичную смазку, которую нужно было прокачивать пресс маслёнкой! th-cam.com/video/5J8n-G6ooPU/w-d-xo.html Да слесаря сами угорают с того что они делают : th-cam.com/video/5J8n-G6ooPU/w-d-xo.html , th-cam.com/video/5J8n-G6ooPU/w-d-xo.html Это похоже редуктор для своего предприятия, начальство сказало - нужно срочно, "сделать нужно было на вчера" А редуктор уже видавший не один ремонт, походу его постоянно клинит. Выходной хвостовик вал-шестерни видно уже обрывало, полумуфта после ремонта со следами РДС видимо шпонку часто срезает
Собирали на холодную а разбирают на горячую с помощью кувалдьі и еще какой--то русской матери Что нельзя постелить какой--то брезент или доски При такой стерильности работать будет недолго
Hitachi EX5600-7 ultra-large hydraulic backhoe excavator has an acces door, maybe your excavator has a tiny one too. Send in your smallest employee he can weld from the inside for extra strenght. Have a nice weekend 😊
The unoffical Hitachi certified Shop repair
😊😊top workers, perfect, prima !!! 😅😅😅
Maravilhoso trabalho e dedicação desses profissionais, todos eles, mas me admiro com o torneiro mecânico.
Amazing craftmanship!
Thank you 🙏 still new for me GEMS but great 👍 job 👏👏👏👍🎥☮️
The first hub that was difficult to remove. If u heat the hub directly over the keyway. It will come off much easier. So heat the entire hub, then while trying to remove focus the heat at the keyway. 20 years+ experience in heavy equipment.
Love that brooms even get the custom, Indian paint job.
Why didn’t you clean the join area before resurfacing the holes. Nice the diameter is oval because of all the crap that was in the join.
round is extra
So that it will come back again soon 😂
when you put that yellow coupling back on heat it up to about 300 degree and then it will have expanded by 0.00000654 inches per degree.
Calculate .00000654 times 6 inches times 200 degrees hotter than workshop temp = .007 or seven thousands expansion.
If workshop is 70 degrees then heating the coupling to 400 degrees would make its bore expand by 11 thou and it would just slide on.
@@paulapalooza8655 you are sick. seek help.
The lathe in the second part looks like a well-kept machine.
Boy the hub was sure seized in there. Nice job guys
Охренеть, сварщик 😅😅😅без маски,в очках варит ...😊шо будет с его рожей, кожей,глазами??я сам сварщик с 30ти летним стажем работы в теплосети.да ,охренеть ты мужик себя ненавидиш.
Nice work
It took every man in the village to get that coupling off!
Bravo majstori!🇸🇮♥️♥️♥️👍👏💪
Veliki pozdrav iz Slovenije!
Спасибо❤❤❤❤
Восхитительно .
The guys perform miracles to the best of their abilities, but in industrialized countries such work is called "wiping your ass with glass"
At least they keep the shop clean inside and out
12:43 professional lifting.....OMG!
Asia... Who cares...
Nice job guys.
Congratulations
I think the gearbox is a copy of a Fuller-Traylor unit. I am actually watching this as prep in-case we have to rebuild ours... If you are using units like this, make sure the oil is THICK. Don't try using low viscosity oil or you'll be getting some new and exciting growls from it.
A estos muchachos les tiras una nave espacial y la sacan andando 👍
Saludos desde Argentina
Hier mag je wel trots op zijn, Groet uit Holland.
facing that metal with a three-jaw was fire
Impressive thread cutting
I used to make the parts to go in these gearboxes - shaft grinding case drilling, etc.
Trabalho magnífico parabéns
Why didn’t you grease the bearings prior to assembly.
Not impressed with the quality of assembly or maintenance.
Your shop is dirty and unsafe.
Oh you're "that guy" Maybe you can upload your videos to your channel so all the experts can leave their opinions about your work. I hope you cheer up and life gets better for you soon ⛳
Just a bit of grease on one end of the rollers. Grease is expensive. It will not be re-greased until it seizes up again.
Even the silicone sealant, they only put a bit near the center. The gears do not seem lubricated very much.
They did not clean the mating surfaces of the two halves before bolting them together and machining, there is dirt in between them.
The shop is a mess. Junk everywhere on the floor. A mountain of chips sitting in the middle.
That guy with the sack is very brave!
😮 excelente
There goes the Hitachi warranty 😄 It would help to grind a bit of the paint off before welding.
1:03:50 shoe on fire, pause.
no big deal. I'm 78 and worked maintenance in papermills and rebuilt many gearboxes and ran lathes that were very old
Easy to be a critic but this job was difficult.Well done overcoming the challenges but the floor should be kept clear before an accident happens,we’ll done workers….
Apparently the quick-change tool post has yet to be introduced to Pakistan
No surface prep not even a degrease. Straight over he top oof impur? Bodge job right there
Why aren’t your people wearing safety boots?
They do wear safety flip-flops.
A few days ago, we copied a cast-iron welding procedure from one of these videos (pile of burning charcoal, borax, gas-welding with cast-iron filler material). Worked great despite us not being able to find the safety sandals or robes for the job. We also deviated from procedure by using a dead wheel-barrow shell as the basis for the furnace.
They have steel toe capped sandals
Would engineers not do better to fit replaceable bearing shells--like automitive main bearings?
There is a reason to use a proper sized key-way instead of a bolt. It helps keep things aligned under load so as not to cause the damage these guys have just spend days fixing.
Now I'm older, my back can not take being stooped over for long periods like many of them.
You forgot the jetway on assembly.
Guy with big-belly, burning hands off, then is allowed to use cold water on them, aaaaahhhhh.
Gearbox needs better lubrication system.
It’s like watching a horror movie
😊 🤙🤙🤙🤙 🙏🏽🙏🏽
Why don’t you clean up the floor? It would be so much safer to work. Get the apprentices to take turns sweeping.
It’s so unprofessional looking.
Its a poor workshop, on an underdevelopped country.
This are smart , efforted guys! My respects❤❤❤😊
el proceso de soldadura de la extensión de la pluma de la excavadora esta mal ejecutada
И что же у него по пизде пошло? Отверстия не разбиты! Подшипники на месте! А вы промахнулись с посадочным под подшипник. Ну бывает и такое.он бы еще поработал. У вас ремонт ради контента.
подшипник провернуло в корпусе, размер ушел. А подшипник заклинило от нагрева, тк там нет смазки. Отверстия под централизованную смазку заткнуты. Слесарь рукой набивал пластичную смазку, которую нужно было прокачивать пресс маслёнкой!
th-cam.com/video/5J8n-G6ooPU/w-d-xo.html
Да слесаря сами угорают с того что они делают : th-cam.com/video/5J8n-G6ooPU/w-d-xo.html , th-cam.com/video/5J8n-G6ooPU/w-d-xo.html
Это похоже редуктор для своего предприятия, начальство сказало - нужно срочно, "сделать нужно было на вчера"
А редуктор уже видавший не один ремонт, походу его постоянно клинит. Выходной хвостовик вал-шестерни видно уже обрывало, полумуфта после ремонта со следами РДС видимо шпонку часто срезает
The loafers…
Собирали на холодную а разбирают на горячую с помощью кувалдьі и еще какой--то русской матери Что нельзя постелить какой--то брезент или доски При такой стерильности работать будет недолго
сначала всю смену епались с распрессовкой, потом кто-то подтащил домкрат и дело пошло быстрее
They either weld with no mask or have to hold it on by hand damn get a real shield.
Whatever machine that booms going on will be severely overloaded.
Just like all their trucks
Был Хитачи, стал Xуeтачи.
OLÁ Mãos Sujas 10/06/24 Sequencia de trabalho errada. Deveriam primeiro inventar a vassoura. Roberto Udo Krapf
Любимый ключ у них - разводной . Плохо им работать
Да, мороки много было.
всё примитив ни какой электроники а как работают ребята молодцы привет из РОССИИ
Bravo! Pozdrav iz Slovenije 🇸🇮♥️♥️♥️👍👏💪
شكرغ
Why would you not use a welding mask. Arc eye is no fun.
Looking working not as teckinition, not using knoledge.
Urge un buen soldador.
Menyedihkan, tidak ada safety shoes, sarung tangan, helm, pakaian kerja, seperti perbudakan.
Look´s like massproduktion in Germany in 2029 ,
but wait,
there is no electric power any more🤣🤣🤣🤣🤣🤣🤣🤣
Do not work with lathe wearing gloves
👏👏👌👌🪛🪛🔧🔧
Это не профи...
Armando nievlapassqorspaaaqorspassqordpassqordpassqorspassqordpassqordpassqorspassqordpassqordpassqordpassqordaemando.nieblapassqorspaaaqordpassqodpassqorspassqorspassqorspassqoespassqorspasswoespaasqorspassqorspassqorsoassqorspasswordpassorspassqorspassqorspssworsdpassworspassqorspaaworspassqordpassqorspassqorspassworspassqordpasaqorspassworspassqorspassworspassworspassqorspassqors
Armando.niwvlapassqorspasaqorspaaaqoespaaaqorspasaqoespasaqorspasaqoesoaaaqoespasaqorspasaqorspasaqorsprspassqorspaaaqorspassqorspassqors