How to Replace Mode Door Actuator 2009-2014 Ford F-150

Buy Now!
New Defroster Door Actuator from 1AAuto.com 1aau.to/ia/1ABM...
This video shows you how to install a new mode door actuator from TRQ on your 2009-2014 Ford F-150.
This process should be similar on the following vehicles:
2009 Ford F-150
2010 Ford F-150
2011 Ford F-150
2012 Ford F-150
2013 Ford F-150
2014 Ford F-150
Tools you will need:
• 8mm Wrench 1aau.to/ohT/1AX...
• 13mm Socket 1aau.to/obuU/1A...
• 8mm Socket 1aau.to/obaV/1A...
• Ratchet 1aau.to/obAV/1A...
• Gloves 1aau.to/o7f/1AX...
• Safety Glasses 1aau.to/oYs/1AX...
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money

[@spaceman1827]

I just did this little job and it was not bad. Here are some things that might help others do this job a little easier. I removed the gas pedal first thing so I could get a socket and ratchet in there to remove the bolts. Once I removed the old actuator I placed the new one right beside to nothe the orientation of the gear. One thing you did not cover is that moving the gear by hand is impossible so heres what I did: i plugged in the new actuator and set my mode to the cabin and feet mode. Once it reached the orientation the same as the old one, I quickly unplugged it. Checked one more time that the new one matched the old ones orientation. It went right in and I bolted it back up. Proceeded to tighten the screws and put the gas pedal back on. Works better than ever now. This video helped me so much and thank you. Just wanted to share my experience and maybe help someone else trying to perform this job.

[@mlu7888]

I was able to get the top screw using an extension on a long handle ratchet and going between the gas and the steering colum.

[@donaldabel1233]

thanks a million, i was worried the dash had to be pulled. that's why i waited until it gave out completely lol

[@MattM-zq9jh]

Dude you rock, this video just saved me over $1000.00, dealerships are out of control. I have a 2014 Raptor it took me about an hour to complete with clean up. I'm 6'2' and 260 so this would have been a biatchhhhhhhhhhh if I did not disconnect the driver seat(This is what made it so easy and quick). I removed the (4) seat bolts with a 15mm socket and 3 inch extension. There are (2) harness connections under the seat. They have tabs that lock the arm down on the harness connection(power and ac seats). They disengage easily by pushing them back so if you are having issues the lock tab is not pushed down enough. Slide the seat back if you have a crew cab. Remove the trim piece just as he described. Remove the (3) 13 mm bolts to free up the gas pedal and push it over out of the way. Then I laid on my back and disconnected the harness just he described. Disconnect the old actuator with the 8mm socket then installed the new one There are arrows on mine for gear gap alignment. It did not want to seat properly at first and I remember seeing the control arm(small silver rod) moved down a little so I pushed it up enough so the gears would align so it would seat properly. I do have a compressor and air tools which saved a lot of time. If you are using a ratchet or wrench it will take a couple of hours and you will definitely need some form of breaker bar for the seat bolts.

[@tacohell]

These instructions are for the mode door actuator and not the blend door actuator (in the center console area). For a 2013, the Motorcraft part number is YH-1881 for the *mode door* actuator. It looks very similar to the *blend door* actuator (and may be the same), but they have different part numbers

[@ArchAngel-FJB]

Is there a specific position I should set the dial to so the new part will drop right in? ( i.e., defrost, dash, floor)

[@GeraldP65]

Thanks for posting this Video ! It helped on my 2014 F150

[@mortgageStrategist]

Worked perfect for my ‘14 f150xlt thanks! Taking the pas pedal off the floor was just what I needed. Not a comfortable (human body wise 🤪) fix, but got it done

[@jamiespringer8141]

Awesome video. But two things not addressed. 1) On single cab F150 with a small rachet no problems getting to the screws. 2) The splines dont match. This is how I did it. Dont know if its the right way but it works. Hook up the Actuator and put one screw to hol. Turn on the air or heat push in the spline and it will move push all the way in when it aligns.

[@user-bf9kp9mu7l]

Thank you for this video

[@enriquecharliejuarez2402]

What type of screws does the part have, why did I lose them or where can I buy them? Thank you, the video helped me

[@PernellDD]

Thanks for the video!

[@user-df3bv7du2o]

What if the gear splines do not line up the same?

[@frankmischler4424]

How do you know if it’s bad

[@adam1299]

Why did you replace it? Mine is clicking when trying to go to vent?

[@WHATDATTOOLDO]

How do you move the white gear

[@edwardwaldron7813]

What’s the best website to purchase the Acutuator

[@TRQ]

+@edwardwaldron7813 Thanks for watching. Buy the part in this video on 1AAuto.com: 1aau.to/m/Shop-TRQ

[@JesseTBaybee]

How do you line the gears up!?!?

[@travisandaliciacardwell7607]

Do u have to remove the fuse for this before you begin?

[@emmanuelperdomo8072]

Are thouse are the same as the one that goes behind the radio??????

[@zyeager83]

I bought a truck that doesn’t have the mode door actuator at all! Also the mounting screws are missing. I can buy the actuator but screws are not included.
Does anyone know what size 8mm screws I need?

[@dh7266]

You didn't remove the dashboard?

[@TRQ]

+D H It is not necessary to remove the dashboard for this repair as the part can be found underneath the dash by the gas pedal.

[@ncsutim]

What is the part number?

[@mytchjoseph1145]

If u just lay on your back you don't have to remove the gas paddle

[@user-lh3xn3qp2o]

This video is NOT for the flow through center console! Take a look how he's replacing the actuator! The shifter is on the steering column! My truck has a center console this is very misleading!