How to Replace Rear Brake Caliper 2008-2012 Honda Accord
ฝัง
- เผยแพร่เมื่อ 23 ส.ค. 2022
- Buy Now!
New Brake Caliper from 1AAuto.com 1aau.to/ia/1ABCR00133
This video shows you how to install a rear brake caliper on your 2008-2012 Honda Accord. A worn out or seized brake caliper can create dangerous and expensive problems: overheating, rotor and pad wear, or even total failure. TRQ brake calipers are engineered to fit your specific vehicle.
This process should be similar on the following vehicles:
2008 Honda Accord
2009 Honda Accord
2010 Honda Accord
2011 Honda Accord
2012 Honda Accord
Tools you will need:
• Pry Bar 1aau.to/oaC/1AXAA00020
• 17mm Wrench 1aau.to/oax/1AXAA00010
• 12mm Socket 1aau.to/oc6/1AXAA00015
• 14mm Socket 1aau.to/oc6/1AXAA00015
• 17mm Socket 1aau.to/oc6/1AXAA00015
• 19mm Socket 1aau.to/obb/1AXAA00043
• Pliers
• 3/8 Inch Air Impact Gun
• Ratchet 1aau.to/odE/1AXAA00016
• Socket Extensions 1aau.to/oc6/1AXAA00015
• Torque Wrench 1aau.to/obL/1AXAA00044
• Brake Grease
• Brake Parts Cleaner
• Drain Pan 1aau.to/oQ/1AXAA00320
• Pick 1aau.to/oae/1AXAA00037
Subscribe: / @trq
Check out our playlist:
Honda Accord 2008-12 8th Gen: • Honda Accord 2008-12 8...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - ยานยนต์และพาหนะ
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
One thing I would say as a Former Honda tech it’s easier if you disconnect and re attach the parking cable while the caliper is bolted to bracket saved me a lot of frustration
Thanks for the clear instructions. This is a big help, doing my honda this weekend.
No clip for the brake pads? Seems like the brakes I been buying for my 08 honda have a spring like clip I have to install into the holes.
Thanks so much, just got my rotors and calipers in the mail and installed them today!
This is great since I just did my rear brakes and had some dripping when pushing the piston back. Looks like this is my next project.
I had to stop this job I couldn't get the e-brake cable off the caliper
This is a perfect tutorial 👌
When you are taking off the emergency brake bolt, this can't be done with a ratchet wrench because there is not enough leverage. You have to loosen it while it's still on. Otherwise you will have to put it back on, which is a hassle. It's easier with the air tool. It's also obviously much easier if you have a lift. Also, these calipers look exactly like the new Raybestos calipers I got from Rock Auto.
I love your videos man you’re extremely educational man! Life saver for real! Question, to “bleed the brakes”, can i do the same process you did which you opened the valve til fluid ran out consistently without the air bubbles?
How important are the washers that you reinstalled?
Got my brake pads, rotors, calipers replaced in my 2009 Honda Accord. Now the handbrake is extremely loose. Should they have adjusted the handbrake at the time of repair? Thanks
Thanks for the video.
How are these TRQ calipers? Are they good quality? Do they last a long time like OEM calipers?
Is hand brake adjustment not needed?
When you remove the emergency brake cable from the back of the caliper, is the emergency brake on or off ?
Thank you 1000%
no bleeding the breaks?
Bob ross of mechanics
Clear and simple !! Thank you
+Ray Ray Thanks for watching our video! 1aau.to/m/Shop-TRQ
this is the only video ive seen then torque that top 17 mm bolt. thanks.
Those carrier bolts were far too loose