Dear Sir what sequence of buttons do I need to push to put a Samsung dual inverter fridge with bottom freezer to force the compressor to come on and check the voltage on the motherboard for this model number. RF27T5241SR
Great video! What if the touchscreen is not showing anything? Just a little red blinking bar next to the temperature. The refrigerator still runs, but the freezer is not freezing cold. Did the touchscreen go bad or is it something else?
Hi, I have Samsung RF4287HARS / XAA - initially my dispenser display unit digits light went off and replaced during the warranty and again after few months the new dispenser display did the same thing. Six months ago, it stopped cooling (compressor did not start ) but some component running sound from the top. replaced the main control board DA41-00683A. now again the same thing happened as six months ago - compressor did not start. Please let me know the force compressor start sequence and suggest me what would be wrong Looks like the compressor has no issue Thanks a lot
hi sir, thankx for the video, my samsung ref. inverter power board light steady with red light in running mode (the compressor is run) but the ref. not cold, what could be the probable cause.? thank you
When I enter forced function mode everything seems to work with the lights are solid on both board. When I exit nothing but the lights work. Any suggestions?
I have 1.6v DC to the inverter board. Led indicator is blank and no output voltage to compressor. Just replaced the inverter board and it's doing the same thing now. Anything else I can Check?
I have an RFG237. The inverter board has a single flash (starting failure). I get a reading of 0v on the compressor signal when I should see 2.5v. Service guide says that the signal is 0-800Hz with a 50% duty cycle. I have a low end multimeter (not true rms). Is it possible that my multimeter not get a true reading, i.e. it may misread that kind of square wave signal?
So meaning there is no output your inverter module, the inverter module receive signal from micro controller, then to the driver then to the inverter modules, check the DC supply 340vdc if available.
rf28hmedbsr , compressor runs and light stays solid. Neither Freeezer nor flex zone seem to stay cold but the upper fridge area seems fine. Any video suggestions on what to test next?
Ok, did all of this and both LEDs are solid. The fridge and freezer will not cool. We had a power surge last night and woke up to it warmer. Performed the reset and it started working. This afternoon it stopped again. No fan and no compressor running unless in FF mode. Ideas?
Thanks for this video... I have been battling with my double door samsung fridge freezer for weeks now and I don't know what else to do again. I got the DA9200483G inverter board and after installation the system control unit at the door , the compressor fan and the lighting in fridge/freezer works but the compressor is not powering up. However samsung compressor tester was use to test it and it power up fine only that the hot pipe is not hot because there is no gas in the compressor. Please what is the issue. All the parts are newly replace parts. Modem no is RSAIUTMG
Thanks for this video. My refrigerator model is RSA1STMG 240 volts and the inverter is top of the fridge. Please let me know if I can get its full inverter control board from you or a compatible replacement. Thank you
I have model RF18HFENBSR. The control panel is on the top of the fridge at the back, but I cannot get it to go into FF mode. Holding the energy saver & fridge buttons for any amount of time, doesn't change the mode. I removed the panel cover and there is only a red indicator light. Thanks for posting this video and for any help you can provide.
Hello, my refrigerator model Samsung RR35H661WW does not cool down. I checked the board. The corresponding LED lamp on the board is on and is fixed. Explain my refrigerator🙏
I have a Samsung RF268ABRS.. The freezer and frig both stopped working at about same time. I had a "fully on LED" at the pc board, fan is running next to compressor, compressor is humming, coils are clean. I have fooled around with these reset buttons on the front panel, and now for some reason the LED is blinking a sequence of 1. I canopy get the LED back to fully on. And , when the compressor was running, there was no air flow at the vents inside the frig. I assume you can feel that flow when the door is open? Im at a loss on why this isn't working.
I have a Samsung Model RF18A5101SR/AA it has an intermittent problem of cooling then every 1-3 days it will stop cooling, It is fairly new but the warranty doesn't apply as I bought it off a 2nd party. I am an appliance repair person but cannot find a tech sheet. and there are no codes from the wifi. Any ideas would help. Thanks
I have a model RF220nctasg/aa that is not cooling. I have confirmed that the main board is supplying power to the inverter, but the inverter board doesn't seem to be doing anything at all. I'm not getting any voltage reading at the compressor either, but that's not really surprising. I've seen that I should be able to put it into the FF mode, but I don't have the front control panel that every video seems to show. 1) How do I activate FF? 2)What does it mean if my inverter board LED isn't coming on at all?
does this board control the heater also? i have a rf323tedbsr, the thermostat is sending signal asking for the heater to come on but is not. i force it to come on manually, putting the unit on defrost and it works but it does not work when the thermostat ask for it. i don't know if this unit has a timer somewhere either any suggestion will be appreciated, keep in mind thermostat is good, heater is good.
@@PartsDr thank you for the quick reply, i would assume is the board, double check everything and i clean the coil that it was very dirty. ill let it run for 3 days and see if it freezes again, i will replace the board. thank u again
Oh! Mine defrost sensor did bench test ok on my unit. It won’t defrost whether in normal mode or Fd mode. Htr element is new. Control board?? Need advice on the road in a rv.
Hi, I have a kenwood bcd-535wpzr/hc4 in the inveter box the led light is flashing 4 time's, does this fault apply to the same as the Samsung on your video? I'd be very grateful if you could help. Thanks Dave
My Samsung fridge model is 401.40483800. Everything works but both evaporator fans have suddenly stopped. No cooling in either compartment. Changed mother board. Nothing! Thinking it’s board DA41-00317A whatcha think??
My defrost heater is not comming on Samsung refrigerator RS25 H5111SR I have tested the ones on heater and sensor they test good please help me where to go next
@@thomassankara2857 no, this fridge is garbage. I had sent a complaint to BBB in New Jersey and samsungs office of the president reached out and offered a free repair. I did try to repair it before all this but the result of the engineers getting involved was that it's my fault. They wash their hands and and don't honor this being a manufactures defect. Look up 'samsung refrigerator recall u.s.a. now' on facebook. Over 26k members and $4 billion payed out for defects.. Never buy samsuck, I know I won't
My fridge used the DA41-00411A inverter board and experiencing the 5 flash error. Samsung cheaped out on no name electrolytic caps. All appeared normal but removed and tested out of circuit every single one was WAY out of spec. Replaced with some budget Cheng caps and compressor is back up running again.
Great comment! I just replaced most of the caps on the same board (was flashing 5 times) and the fridge runs again. 3 of the 4 47uf caps were bad, replaced all of them as well as the 470’s just cause i had them laying around, Bingo, fridge works again!
Thanks a lot for this video.. I really need your help on what to do next. I have this model RSAIUTMG fridge/freezer. All the control parts PCB including the inverter power board DA9200483G were changed with new parts. After installation the control unit of the fridge on the door, the compressor fan and inner light of the fridge and freezer works fine except the compressor refused to power on. Samsung compressor tester was used and it powers up the compressor only that the heated pipe of the compressor was not getting hot as a result of insufficient or no gas inside it. Pls I need help on what to do now. I have checked to see that current is flowing to the wire that goes to the compressor. Thanks for your assistance
Hi sir thanks for this video I find it helpful, my model RSA1STMG n it's blinking 4 times,is it right to conclude in totality that it's the compressor or there are other factors too?
hello Ryan, my Samsun RF4287HARS/XAA refrigerator will not stay in force mode I can't get FF 1 for about 30 seconds and then it goes to 0F. the compressor never comes on. Does this indicate anything. Thanks look forward to your response
I have a solid LED light. Freezer works great, refrigerator compartment doesn’t. Repair guy said compressor works, and that it needs a new control board. Does that sound right?
If the compressor is working properly, then the problem should not relate to the inverter board. More troubleshooting would need to be done to see what is causing the refrigerator section to not cool properly.
You need to check first the system voltages if available .like the 340vdc after the rectifier ,then the 5vdc for the micro controller. And other systems voltages.
No, it will only have voltage during the defrost cycle. You can try putting the refrigerator into FD (forced defrost) mode to check voltage. We show how to do that in this video here: th-cam.com/video/1DQZs75GEWQ/w-d-xo.html
@@PartsDr Yes I’ve done that and I replaced the htr because the diagnostic code pointed to that. Before putting into Fd I put the magnets on the box to fool it and and it never heated up. (Maybe I don’t need to use the magnets when running a Fd?) No voltage coming from the connectors on the frig. Defrost sensors ohm checked out good against the chart. It is not defrosting at all. I’ve done a few things to mitigate air infiltration too including redoing Evap cover gasket. Do I need to pull it and check the inverter box? When I say pull it it’s in a motorhome and has been working fine for yrs. It actually cools really well until it frosts up again. Help, we are on the road!
Hi, I have a samsung model RF263TEAESR/AA SERIAL JKG04BBH600176A that the evaporator fans don't work,I already checked them and the fans are fine, could you help me tell me what are the cables that come out of the board for the fans, thank you
@@PartsDr Thanks a lot for this video.. I really need your help on what to do next. I have this model RSAIUTMG fridge/freezer. All the control parts PCB including the inverter power board DA9200483G were changed with new parts. After installation the control unit of the fridge on the door, the compressor fan and inner light of the fridge and freezer works fine except the compressor refused to power on. Samsung compressor tester was used and it powers up the compressor only that the heated pipe of the compressor was not getting hot as a result of insufficient or no gas inside it. Pls I need help on what to do now. I have checked to see that current is flowing to the wire that goes to the compressor. Thanks for your assistance. pls I need response from you. Thanks
Mine is doing the same. Solid LED, freezer working but refrigerator compartment isn’t cooling. Compressor is working. Would this be a control board issue?
The LED is on solid and compressor is on but the freezer in not cooling or freezing. the refrigerator model is RS25H5111SG/AA. any suggestions please? thanks
Samsung model number rf26XAEBP, unplugged for 10 minutes comes back in OF OF (demo mode I guess) I reset it using top left and right button. I resets for 3 seconds then goes back into OF OF. How do I test the front door panel or is it shot or something else? Thanks
Samsung rs265tdrs : Both inverter board and motherboard flash once. Compressor not coming on at all. FF mode on makes no difference. Fault code mode shows no faults. Tested compressor windings and all of the 3 positions show 11.2 ohms. Not shorted to ground. Inverter board was removed and I don't see any obvious signs of damage. Are we looking at bad compressor or inverter board? I hate now that fridges are computers. Which components fail on the inverter board? Capacitors are not blown.
Hello! Please help! We have been without our refrigerator for a month now. Our daughter accidentally left the door open 1/4” for 2 days (we were away from home). We closed it immediately when we saw it. However, the freezer would know longer get cold. We did the self diagnostic test on the front and it blinked 3 times for inverter board. We replaced the inverter board but it still has 3 blinks and now neither the fridge or freezer will cool. There is a solid red light, compressor comes on, and fan works. Can you please help us? Model is Samsung RF268ABBP.
1 flash is a starting failure. Service info says to first check electrical connectors, if good then replace inverter control board. If same problem after that replace compressor.
@@PartsDr I have the same problem on a Samsung RF4289HARS. Connections are good but I’m unable to find the inverter control board online. Do you have a link for the part so I can order it?
My Samsung Model RT21M6213SR has no power and nothing works. The unit is a little over 2 yrs old. I've done all the trouble shooting - plug, breakers, different outlets etc... will replacing inverter control board resolve this issue?
Hi I have a Samsung RF28HMEDBSR/AA refrigerator I checked the board the light is not blinking AND I get a reading of 1.574 on my meater the compressor comes on immediately when it's set on the FF mode I have replaced the thermal sensors on the freezer and the fridge part both fans are working I replaced the fan on the freezer it still will not cool.the fan of the compressor comes on when the compressor comes on. I also replaced the assembly wire on the compressor I don't know what else to do to fix the problem the refrigerator will not cool at all
Model RS25H5111SR/AA My Samsung refrigerator only 7yrs stop working and there is only a flashing white light on the front panel. Any idea what it is? Or, is it better to buy a new refrigerator ? Need some guidance/help. I unplug it, now for 2 days, still just that light flashing.
Freezer Top 2 coils light frost,below that moist but cool. No err codes no flashes on pcb board. Refer is fine and reaches directed temps. Freezer won’t drop below 31. All fans are working. Compressor runs and gets warm and light vibration. Of course ice maker isn’t working. Temp sensors work. I’m out of ideas.
Model RF260BEAESR/AA. I could not get the FF mode. There is no blank control screen to start with. it shows 75 F and 75 F for fridge and freezer. the LED in the back is blinking and code says 81 E. for this model compressor starts failing is the definition of the code. I believe compressor is "kaput".
Hello PartsDr and thank you for your contribution my refrigerator says E 84 which corresponds to Motor locked over RPM but I don't know how to check the voltage on th resistance R308. The refrigerator is working but the freezer is not . Thank you
my Samsung Model is RF31FMESBSR AND THE FREEZER is not getting cold. the compressor is running and the fan is working. the invertor board has a solid red light. what do i check next.
How can he measure the output p.w.m. signal from the main control board looking at the input to the inverter board with the cable disconnected, I think this guy is confused, you have to measure at the cable and i’m not sure but it may have to be connected to see proper levels.
On my samsung rf265abbp, the display shows -8'F for freezer and 38'F for fridge but no buttons work anymore. Had an episode yesterday where freezer and fridge both weren't holding respective proper temps. Unloaded and then 5 hours later freezer and fridge started working again. Ugh! How can I check the board?
My compressor is turning on, the red light on my mainboard is solid, but the fridge isn't cooling. Samsung technician said my sealed system is covered under warranty but claims the mainboard is broken and they want me to pay $500 to replace it. I'm planning on buying a multimeter to test for sure but it seems to me that the mainboard is fine and they're just trying to charge me for the repair that I'm supposed to be covered for.
my fridge DA92-00988C inverter LED only turns on for a brief second when initially plugging in then it goes out. Only thing which turns on is the Family Hub computer screen but nothing else works. Water/Ice LED's in the front of the fridge just blinks. Tried changing out the inverter board with no change.
Some refrigerators are not designed to operate on GFCI outlets. Check your owners manual or with the manufacturer to see if yours is compatible to operate on a GFCI outlet.
I get 4 flashes in LED. Motor lock/ over RPM. How can I fix that? Do I need to replace the motor? If so can I do it myself or do I need to get someone certified to work with compressors?
@@PartsDr pls mine also do this RSAIUTMG but when tested with samsung compressor diagnosing tool JIG it works but with the pcb inverter it shows 4flashes. What else to do pls. Also note when I test with JIG the compressor comes up but doesn't get hot on the pipe side as there is no refrigerant inside it.
Light is solid, the compressor comes on but the air coming out at the back is cool not hot. The freezer is cold. The evaporator fan will not come on had a tech out to replace it and the thermistor. Not sure what it could be.
Thanks for this video. After watching your video, I decided to open the back panel of the refrigerator with model no. RS25H5111SR. I realized the inverter light stayed on for some time and completely went off after. How do I check if my inverter board or mainboard is faulty? Thank you.
My Samsung 4 door flex cool has stopped working. Our power went our for about 5 seconds and now it won't come back on. I have tried the manual reset but no go. The unit clicks and the fan tries to move but no go. Model # RF23J9011SG/AA. Any suggestions as I do not want to pay 100.00 for a service call if I can fix myself
It's not supposed to run all the time. What are your freezer and fridge temps? It may be overheating due to low refrigerant. Professional needs to check.
Usually, the recommendation for 5 blinks is to first replace the inverter control board. If that doesn't fix it, then you would need to have a professional replace the compressor.
My freezer is working fin. The refrigerator is freezing up. I replaced the evaporator fan and it still wont come on. I also tested the door switches they seem to be fine. What else could cause the evaporator fan not to come on in a samsung french door Frig.
Computer engineering student here with limited knowledge of this system. I have the same problem freezing up. The recirculation fan works but ultimately freezes along with the evaporation core and drain system. I verified the heating element has 100ohms (good) and the temperature thermistor disengaged with a blow dryer after some time (good). The temp sensors are negative coefficient and decrease resistance with heat applied (good). Everything points to a control board or power supply due to prolonged time frame of freeze up. I see a solid red led on the inverter board while it cools back down from a complete evap freeze up. Anyone chime in?
So the led is lit and solid but my freezer has not been freezing up. Now that I see that there are no issues how should I proceed? Any other trouble shooting ideas??
The main is flashing one time. I have been told it is an inverter problem. However, I can't find the part. Model # RF237AARS/Model Code RFG237AARS/XAA - number on the sticker on the inverter - 06DA4100614FP126ZB6344. Other number found - DA27-00020A. AW Inverter BK2 110v. Can you please help me locate the part? Thanks
Shock Pulse Monitoring also known as SPM is a patented technique of predictive maintenance by measuring vibration and shock pulses of bearing in motors and to identify their condition and operating life before the next overhaul procedure. Service info for the 2 blink SPM Fault says to check the sealed system for restriction and refrigerant, if okay replace inverter, if same, replace the compressor.
Our refrigerator is flashing 0 FF i try several codes but it will not come out. Refrigerator will not cool. Inverted board burnt under heat sink. Can you help us? Model no. is RF28JBEDBSG/AA
What are the likely culprits for Under Voltage?
Faulty capacitors on the inverter. They don't have to be bulged to be bad. The supplier Samsung uses is 💩.
Dear Sir what sequence of buttons do I need to push to put a Samsung dual inverter fridge with bottom freezer to force the compressor to come on and check the voltage on the motherboard for this model number. RF27T5241SR
Great video! What if the touchscreen is not showing anything? Just a little red blinking bar next to the temperature. The refrigerator still runs, but the freezer is not freezing cold. Did the touchscreen go bad or is it something else?
Hi it was a very useful video. Can you tell me the function sequences on my fridge with model: RT81DTBSP?
Whirlpool model RF265ABPN compressor control board defrost troubleshooting. Thank You Justin
Hi, I have Samsung RF4287HARS / XAA - initially my dispenser display unit digits light went off and replaced during the warranty and again after few months the new dispenser display did the same thing.
Six months ago, it stopped cooling (compressor did not start ) but some component running sound from the top. replaced the main control board DA41-00683A. now again the same thing happened as six months ago - compressor did not start.
Please let me know the force compressor start sequence and suggest me what would be wrong
Looks like the compressor has no issue
Thanks a lot
hi sir, thankx for the video, my samsung ref. inverter power board light steady with red light in running mode (the compressor is run) but the ref. not cold, what could be the probable cause.? thank you
When I enter forced function mode everything seems to work with the lights are solid on both board. When I exit nothing but the lights work. Any suggestions?
Replace
Thanks for sharing this video, it helped us save big in shop fees.
Great!
I have 1.6v DC to the inverter board. Led indicator is blank and no output voltage to compressor. Just replaced the inverter board and it's doing the same thing now. Anything else I can Check?
Hi Eric, I have the same issue, did you find the solution for this ?
I have an RFG237. The inverter board has a single flash (starting failure). I get a reading of 0v on the compressor signal when I should see 2.5v. Service guide says that the signal is 0-800Hz with a 50% duty cycle. I have a low end multimeter (not true rms). Is it possible that my multimeter not get a true reading, i.e. it may misread that kind of square wave signal?
It sounds like you need a multimeter that can read voltage frequency. The Fluke 117 we show in the video has this feature.
So meaning there is no output your inverter module, the inverter module receive signal from micro controller, then to the driver then to the inverter modules, check the DC supply 340vdc if available.
Thank you but isnt also the harness cn75 pin four should read 2.5vdc ?? Your test is,simular but indeed effective
rf28hmedbsr , compressor runs and light stays solid. Neither Freeezer nor flex zone seem to stay cold but the upper fridge area seems fine. Any video suggestions on what to test next?
Ok, did all of this and both LEDs are solid. The fridge and freezer will not cool. We had a power surge last night and woke up to it warmer. Performed the reset and it started working. This afternoon it stopped again. No fan and no compressor running unless in FF mode. Ideas?
Thanks for this video... I have been battling with my double door samsung fridge freezer for weeks now and I don't know what else to do again. I got the DA9200483G inverter board and after installation the system control unit at the door , the compressor fan and the lighting in fridge/freezer works but the compressor is not powering up. However samsung compressor tester was use to test it and it power up fine only that the hot pipe is not hot because there is no gas in the compressor. Please what is the issue. All the parts are newly replace parts. Modem no is RSAIUTMG
@@harryofume8792 what ?
Thanks for this video. My refrigerator model is RSA1STMG 240 volts and the inverter is top of the fridge. Please let me know if I can get its full inverter control board from you or a compatible replacement. Thank you
Sorry, we are not able to look up parts for non-USA models.
I have model RF18HFENBSR. The control panel is on the top of the fridge at the back, but I cannot get it to go into FF mode. Holding the energy saver & fridge buttons for any amount of time, doesn't change the mode. I removed the panel cover and there is only a red indicator light. Thanks for posting this video and for any help you can provide.
Hello, my refrigerator model Samsung RR35H661WW does not cool down. I checked the board. The corresponding LED lamp on the board is on and is fixed. Explain my refrigerator🙏
I have a Samsung RF268ABRS.. The freezer and frig both stopped working at about same time. I had a "fully on LED" at the pc board, fan is running next to compressor, compressor is humming, coils are clean. I have fooled around with these reset buttons on the front panel, and now for some reason the LED is blinking a sequence of 1. I canopy get the LED back to fully on. And , when the compressor was running, there was no air flow at the vents inside the frig. I assume you can feel that flow when the door is open? Im at a loss on why this isn't working.
How do I know which is the ground, which is the signal? All my schematic shows me are the colors, which I can already see in the wires.
Could the freezer air flow door be bad? How do you teat that?
I have a Samsung Model RF18A5101SR/AA it has an intermittent problem of cooling then every 1-3 days it will stop cooling, It is fairly new but the warranty doesn't apply as I bought it off a 2nd party. I am an appliance repair person but cannot find a tech sheet. and there are no codes from the wifi. Any ideas would help. Thanks
Good video.
Thanks!
How to run a diagnostic check on a Samsung Rereigerator Model RSG257AARS
I have a model RF220nctasg/aa that is not cooling. I have confirmed that the main board is supplying power to the inverter, but the inverter board doesn't seem to be doing anything at all. I'm not getting any voltage reading at the compressor either, but that's not really surprising. I've seen that I should be able to put it into the FF mode, but I don't have the front control panel that every video seems to show. 1) How do I activate FF? 2)What does it mean if my inverter board LED isn't coming on at all?
does this board control the heater also?
i have a rf323tedbsr, the thermostat is sending signal asking for the heater to come on but is not. i force it to come on manually, putting the unit on defrost and it works but it does not work when the thermostat ask for it.
i don't know if this unit has a timer somewhere either
any suggestion will be appreciated, keep in mind thermostat is good, heater is good.
No, the main control board is what controls the power to the defrost heaters.
@@PartsDr thank you for the quick reply, i would assume is the board, double check everything and i clean the coil that it was very dirty. ill let it run for 3 days and see if it freezes again, i will replace the board.
thank u again
@@victorl5891 We would also recommend to replace the defrost sensor as sometimes they can bench test okay, but act up intermittently while in use.
Oh! Mine defrost sensor did bench test ok on my unit. It won’t defrost whether in normal mode or Fd mode. Htr element is new. Control board?? Need advice on the road in a rv.
Hi, I have a kenwood bcd-535wpzr/hc4 in the inveter box the led light is flashing 4 time's, does this fault apply to the same as the Samsung on your video? I'd be very grateful if you could help. Thanks Dave
Hi Dave, I'm sorry but we do not have any information on your refrigerator.
My Samsung fridge model is 401.40483800.
Everything works but both evaporator fans have suddenly stopped. No cooling in either compartment. Changed mother board. Nothing! Thinking it’s board DA41-00317A whatcha think??
Thanks a lot for sharing your thoughts
👍
My defrost heater is not comming on Samsung refrigerator RS25 H5111SR I have tested the ones on heater and sensor they test good please help me where to go next
Same problems with my exact model number. Sounds like a main PCB board (defrost timer). Did you figure it out?
@@natem3152 I have same problem, we're you able to figure it out? Thanks.
@@thomassankara2857 no, this fridge is garbage. I had sent a complaint to BBB in New Jersey and samsungs office of the president reached out and offered a free repair. I did try to repair it before all this but the result of the engineers getting involved was that it's my fault. They wash their hands and and don't honor this being a manufactures defect. Look up 'samsung refrigerator recall u.s.a. now' on facebook. Over 26k members and $4 billion payed out for defects.. Never buy samsuck, I know I won't
My fridge used the DA41-00411A inverter board and experiencing the 5 flash error. Samsung cheaped out on no name electrolytic caps. All appeared normal but removed and tested out of circuit every single one was WAY out of spec. Replaced with some budget Cheng caps and compressor is back up running again.
Great! Thanks for sharing!
Great comment! I just replaced most of the caps on the same board (was flashing 5 times) and the fridge runs again. 3 of the 4 47uf caps were bad, replaced all of them as well as the 470’s just cause i had them laying around, Bingo, fridge works again!
Also, If I had to guess, the ebay repair kits for this board is just 7 smaller electrolytic capacitors.
@@jonl5889 Correct. I saw those ebay listings too. Another buyer gave feedback confirming just a cap kit.
Thanks a lot for this video.. I really need your help on what to do next. I have this model RSAIUTMG fridge/freezer. All the control parts PCB including the inverter power board DA9200483G were changed with new parts. After installation the control unit of the fridge on the door, the compressor fan and inner light of the fridge and freezer works fine except the compressor refused to power on. Samsung compressor tester was used and it powers up the compressor only that the heated pipe of the compressor was not getting hot as a result of insufficient or no gas inside it. Pls I need help on what to do now. I have checked to see that current is flowing to the wire that goes to the compressor. Thanks for your assistance
Your inverter is not working. That is why the compressor motor not working. Or the compressor is dead.
So I have a solid light on but I don't hear the compressor can it still be the circuit board
Hi sir thanks for this video I find it helpful, my model RSA1STMG n it's blinking 4 times,is it right to conclude in totality that it's the compressor or there are other factors too?
Is an electronic board failure covered by Samsung’s warranty past the 2 year mark?
You will need to check your owner's manual or contact the manufacturer for the warranty details on your specific appliance.
My fridge flashed four times. What does this mean? Help me, you are a specialist in this and thank you
4 flashes usually means that the motor/compressor is locked.
Mines flashes 4 times too. What do I need to fix it? Thanks
I have a single light flash....and the fridge keeps restarting.... is that the main board or the inverter board issue?
hello Ryan, my Samsun RF4287HARS/XAA refrigerator will not stay in force mode I can't get FF 1 for about 30 seconds and then it goes to 0F. the compressor never comes on. Does this indicate anything. Thanks look forward to your response
I have rf261beaesr/aa the compressor isnt coming on
I have a solid LED light. Freezer works great, refrigerator compartment doesn’t. Repair guy said compressor works, and that it needs a new control board. Does that sound right?
If the compressor is working properly, then the problem should not relate to the inverter board. More troubleshooting would need to be done to see what is causing the refrigerator section to not cool properly.
You need to check first the system voltages if available .like the 340vdc after the rectifier ,then the 5vdc for the micro controller. And other systems voltages.
Not getting 125v at the defrost htr for Evap? Should there always be voyage there until the htr stat lets it pass thru?
No, it will only have voltage during the defrost cycle. You can try putting the refrigerator into FD (forced defrost) mode to check voltage. We show how to do that in this video here: th-cam.com/video/1DQZs75GEWQ/w-d-xo.html
@@PartsDr
Yes I’ve done that and I replaced the htr because the diagnostic code pointed to that. Before putting into Fd I put the magnets on the box to fool it and and it never heated up. (Maybe I don’t need to use the magnets when running a Fd?) No voltage coming from the connectors on the frig. Defrost sensors ohm checked out good against the chart. It is not defrosting at all. I’ve done a few things to mitigate air infiltration too including redoing Evap cover gasket. Do I need to pull it and check the inverter box? When I say pull it it’s in a motorhome and has been working fine for yrs. It actually cools really well until it frosts up again. Help, we are on the road!
Sir what is the supply voltages of the compressor motor. Thank
Hi, I have a samsung model RF263TEAESR/AA
SERIAL JKG04BBH600176A
that the evaporator fans don't work,I already checked them and the fans are fine, could you help me tell me what are the cables that come out of the board for the fans, thank you
Hello sir, I have a solid lit LED, evaporator fan working, compressor powering up but still fridge is not cooling. Any trouble shooting ideas?
Are both the freezer and refrigerator compartments not cooling?
@@PartsDr Thanks a lot for this video.. I really need your help on what to do next. I have this model RSAIUTMG fridge/freezer. All the control parts PCB including the inverter power board DA9200483G were changed with new parts. After installation the control unit of the fridge on the door, the compressor fan and inner light of the fridge and freezer works fine except the compressor refused to power on. Samsung compressor tester was used and it powers up the compressor only that the heated pipe of the compressor was not getting hot as a result of insufficient or no gas inside it. Pls I need help on what to do now. I have checked to see that current is flowing to the wire that goes to the compressor. Thanks for your assistance. pls I need response from you. Thanks
Mine is doing the same. Solid LED, freezer working but refrigerator compartment isn’t cooling. Compressor is working. Would this be a control board issue?
@@PartsDr fridge not cooling only freezer
SAME THING WITH MINE
Hello sir do you have samsung fridgadair vwbo9m221mki inverter?
Hi. I have a Samsung model rf28k9380sr, is not freezing, the light in the inverter board is on, solid. Any idea what is going on? Thanks
The LED is on solid and compressor is on but the freezer in not cooling or freezing. the refrigerator model is RS25H5111SG/AA. any suggestions please? thanks
Hello Sir I have a case of samsung inverter with triple-blink refrigerator. Where the cause of his damage
Hi, I have three flashes... Replace board?
Samsung model number rf26XAEBP, unplugged for 10 minutes comes back in OF OF (demo mode I guess) I reset it using top left and right button. I resets for 3 seconds then goes back into OF OF. How do I test the front door panel or is it shot or something else? Thanks
Samsung rs265tdrs : Both inverter board and motherboard flash once. Compressor not coming on at all. FF mode on makes no difference. Fault code mode shows no faults. Tested compressor windings and all of the 3 positions show 11.2 ohms. Not shorted to ground. Inverter board was removed and I don't see any obvious signs of damage. Are we looking at bad compressor or inverter board? I hate now that fridges are computers. Which components fail on the inverter board? Capacitors are not blown.
Yup same
@@eriksxo i replaced inverter board and everything was fixed
@@Bizija123 appreciate it. Gonna replace mine as well
Hello!
Please help! We have been without our refrigerator for a month now. Our daughter accidentally left the door open 1/4” for 2 days (we were away from home). We closed it immediately when we saw it. However, the freezer would know longer get cold. We did the self diagnostic test on the front and it blinked 3 times for inverter board. We replaced the inverter board but it still has 3 blinks and now neither the fridge or freezer will cool. There is a solid red light, compressor comes on, and fan works. Can you please help us? Model is Samsung RF268ABBP.
Hi, main its flashing 1 time on the main board and inverter board. Any help. Thank you
1 flash is a starting failure. Service info says to first check electrical connectors, if good then replace inverter control board. If same problem after that replace compressor.
@@PartsDr I have the same problem on a Samsung RF4289HARS. Connections are good but I’m unable to find the inverter control board online. Do you have a link for the part so I can order it?
@@peterjung5965 Can you please post the numbers from the barcode sticker on your original board?
@@PartsDr 06DA9200215CP171B9TA264
@@peterjung5965 Here is a link to the part: partsdr.com/part/da92-00215c-inverter-control-board
My Samsung Model RT21M6213SR has no power and nothing works. The unit is a little over 2 yrs old. I've done all the trouble shooting - plug, breakers, different outlets etc... will replacing inverter control board resolve this issue?
A bad inverter board would not act that way, but a bad main control board could cause those types of symptoms.
Good evening! I have a question too! My fridge only lights up once and it doesn't work, could you tell me why ?! Starting Failure?!?
Hi I have a Samsung RF28HMEDBSR/AA refrigerator I checked the board the light is not blinking AND I get a reading of 1.574 on my meater the compressor comes on immediately when it's set on the FF mode I have replaced the thermal sensors on the freezer and the fridge part both fans are working I replaced the fan on the freezer it still will not cool.the fan of the compressor comes on when the compressor comes on. I also replaced the assembly wire on the compressor I don't know what else to do to fix the problem the refrigerator will not cool at all
Model RS25H5111SR/AA My Samsung refrigerator only 7yrs stop working and there is only a flashing white light on the front panel. Any idea what it is? Or, is it better to buy a new refrigerator ? Need some guidance/help. I unplug it, now for 2 days, still just that light flashing.
The flashing light on the front display would indicate an error code. Similar to this: partsdr.com/blog/samsung-blinking-dashline-error-code-list/
If my fridge freeze what do tink its the problem ? Samsung rf260beasr
Tech replace inverter board with what look like a use one and fridge still doesn't work hopefully this guide will help me
rf263beaesg/aa not cooling, both main board and inverter board are good and compressor is good and no error codes.
Probably leak inside coils?
Which buttons do I use
Light is solid, power is optimum, fan is working, still no cool. Should I assume low/no freon?
It could be a sealed system leak. Usually the easiest way to determine that is by looking at the frost pattern on the evaporator coil(s).
Freezer Top 2 coils light frost,below that moist but cool. No err codes no flashes on pcb board. Refer is fine and reaches directed temps. Freezer won’t drop below 31. All fans are working. Compressor runs and gets warm and light vibration. Of course ice maker isn’t working. Temp sensors work. I’m out of ideas.
Model RF260BEAESR/AA. I could not get the FF mode. There is no blank control screen to start with. it shows 75 F and 75 F for fridge and freezer. the LED in the back is blinking and code says 81 E. for this model compressor starts failing is the definition of the code. I believe compressor is "kaput".
Hello PartsDr and thank you for your contribution my refrigerator says E 84 which corresponds to Motor locked over RPM but I don't know how to check the voltage on th resistance R308. The refrigerator is working but the freezer is not .
Thank you
Hey, did you ever figure this out? I'm having the same issue with my fridge.
my Samsung Model is RF31FMESBSR AND THE FREEZER is not getting cold. the compressor is running and the fan is working. the invertor board has a solid red light. what do i check next.
My model # RF266AEPN does not seem to have the same sequence LED is flashing 5 times.
How can he measure the output p.w.m. signal from the main control board looking at the input to the inverter board with the cable disconnected, I think this guy is confused, you have to measure at the cable and i’m not sure but it may have to be connected to see proper levels.
He's got the power on.. He's measuring voltage, aren't you describing a continuity test?
Hi sir on pcb board i am hearing 2 time rely click sound... but no lights on both board.
On my samsung rf265abbp, the display shows -8'F for freezer and 38'F for fridge but no buttons work anymore. Had an episode yesterday where freezer and fridge both weren't holding respective proper temps. Unloaded and then 5 hours later freezer and fridge started working again. Ugh! How can I check the board?
My compressor is turning on, the red light on my mainboard is solid, but the fridge isn't cooling. Samsung technician said my sealed system is covered under warranty but claims the mainboard is broken and they want me to pay $500 to replace it. I'm planning on buying a multimeter to test for sure but it seems to me that the mainboard is fine and they're just trying to charge me for the repair that I'm supposed to be covered for.
can the converter make the fridge Department Frozen
No, the inverter would not relate to that. Try testing your temperature sensors th-cam.com/video/J5bwcteeJNM/w-d-xo.html
my fridge DA92-00988C inverter LED only turns on for a brief second when initially plugging in then it goes out. Only thing which turns on is the Family Hub computer screen but nothing else works. Water/Ice LED's in the front of the fridge just blinks. Tried changing out the inverter board with no change.
Any idea why the fridge kills my GFCI when the compressor comes on but no fuse or breaker? Where can I get model or board number schematic?
Some refrigerators are not designed to operate on GFCI outlets. Check your owners manual or with the manufacturer to see if yours is compatible to operate on a GFCI outlet.
@PartsDr It has been plugged into a GFCI since we bought it. That being said I'm trying to run it on a generator while our power is out.
I get 4 flashes in LED.
Motor lock/ over RPM.
How can I fix that? Do I need to replace the motor? If so can I do it myself or do I need to get someone certified to work with compressors?
It is usually caused by a bad compressor which will need to be replaced by a liscened and trained technician.
@@PartsDr pls mine also do this RSAIUTMG but when tested with samsung compressor diagnosing tool JIG it works but with the pcb inverter it shows 4flashes. What else to do pls. Also note when I test with JIG the compressor comes up but doesn't get hot on the pipe side as there is no refrigerant inside it.
Light is solid, the compressor comes on but the air coming out at the back is cool not hot. The freezer is cold. The evaporator fan will not come on had a tech out to replace it and the thermistor. Not sure what it could be.
I have a Samsung refrigerator model number rf323tedbsr I'm trying to figure out what the sequence is to reset my front panel
How can i force a reset on my samsung RSJ1KERS side by side?
awsome man thanks
You're welcome!
How we measure the number of flashes. Are these counted in one minute
it will blink every second and then will stop for aprox 7 seconds...then it will go back to every second ....count the every second
Thanks for this video. After watching your video, I decided to open the back panel of the refrigerator with model no. RS25H5111SR. I realized the inverter light stayed on for some time and completely went off after. How do I check if my inverter board or mainboard is faulty? Thank you.
My light is solid, but the compressor is not coming on. I have a 23 C code. That is the fan I believe. Also sometimes the 83C code comes up.
Samsung refrigerator rf287201sr light flash on circuit board bought it scratch and dent but came with no relay or overload to the compressor
It is normal to not have a start relay and overload if you have an inverter board. See this video here: th-cam.com/video/dT0DTjktRUY/w-d-xo.html
Sir can you please say why my samsung fridge displaying the word filter model #R f23t5ad133/ap
My Samsung 4 door flex cool has stopped working. Our power went our for about 5 seconds and now it won't come back on. I have tried the manual reset but no go. The unit clicks and the fan tries to move but no go. Model # RF23J9011SG/AA. Any suggestions as I do not want to pay 100.00 for a service call if I can fix myself
How test mode activet Samsung sbs refrigerator how to selfcheck comments in voltages pls tell me sir tq🙏🙏🙏
Please I have Samsung rf28hmedbsr model and my motor compressor keeps stopping. It cannot stay on for more than 1 hour
It's not supposed to run all the time. What are your freezer and fridge temps? It may be overheating due to low refrigerant. Professional needs to check.
I experience unit icing evarotor and chiller side not cooling what is the possibly trouble Samsung inverter
keep in mind that the signal on some fridges is a square or pwm signal, many multimeters will not read correctly so don’t assume bad control board.
Hello sir, inverter PCB have 3 blinks and the main 10 blinks...can you help me for that issue...thanks
Hi I have a samsung model rf25hmedbsr and the cooling fans are not running any comments
Hi I have a Samsung fridge srf693gdss inverter board blinking 5 times .
Usually, the recommendation for 5 blinks is to first replace the inverter control board. If that doesn't fix it, then you would need to have a professional replace the compressor.
@@PartsDr fixed it ,it was the inverter board thanks for tips 👍
@@luxostucco2772 Great! Thanks for letting us know!
How to check samsung refrigerator model no s626
I have RM255BARB. (Samsung) not cooling or freezing. No error codes
My freezer is working fin. The refrigerator is freezing up. I replaced the evaporator fan and it still wont come on. I also tested the door switches they seem to be fine. What else could cause the evaporator fan not to come on in a samsung french door Frig.
Computer engineering student here with limited knowledge of this system. I have the same problem freezing up. The recirculation fan works but ultimately freezes along with the evaporation core and drain system. I verified the heating element has 100ohms (good) and the temperature thermistor disengaged with a blow dryer after some time (good). The temp sensors are negative coefficient and decrease resistance with heat applied (good). Everything points to a control board or power supply due to prolonged time frame of freeze up. I see a solid red led on the inverter board while it cools back down from a complete evap freeze up. Anyone chime in?
So the led is lit and solid but my freezer has not been freezing up. Now that I see that there are no issues how should I proceed? Any other trouble shooting ideas??
Check the evaporator fan motor in the freezer to make sure it is running. th-cam.com/video/OpLI6PTJ4hg/w-d-xo.html
The main is flashing one time. I have been told it is an inverter problem. However, I can't find the part. Model # RF237AARS/Model Code RFG237AARS/XAA - number on the sticker on the inverter - 06DA4100614FP126ZB6344. Other number found - DA27-00020A. AW Inverter BK2 110v. Can you please help me locate the part? Thanks
It looks like it is discontinued and no longer available from the manufacture partsdr.com/part/da41-00614f-inverter-control-board
Hi I have 3 blinks on both boards.any help?
What is the model number of the refrigerator? th-cam.com/video/4HhWL9sonuE/w-d-xo.html
good pm. i have a problem. my inverter no frost has burned. please help.
Rt 53h6670slme compressor not working?how to check step by step
What if there’s no power at all
i have two blinks, what does "SPM" means, ?
Shock Pulse Monitoring also known as SPM is a patented technique of predictive maintenance by measuring vibration and shock pulses of bearing in motors and to identify their condition and operating life before the next overhaul procedure.
Service info for the 2 blink SPM Fault says to check the sealed system for restriction and refrigerant, if okay replace inverter, if same, replace the compressor.
Our refrigerator is flashing 0 FF i try several codes but it will not come out. Refrigerator will not cool. Inverted board burnt under heat sink. Can you help us? Model no. is RF28JBEDBSG/AA