From what I've found those chainsaws should be putting out roughly 4.5HP each. Total of 72hp. Chainsaws typically have a rev ceiling of 12-14k RPM. Probably double that of the original Lada motor. You could change the pulley diameters around on those timing belts. Give it a 2:1 gear reduction. Your output rpm would be 6-7k and the torque would be double.
This is the way. Your main power transfer shaft is way too heavy to get up to that RPM number, so a 1:2 gear reduction is needed. The neatest way to do it is to remove the pulleys altogether and install actual gears. Would probably be easier to balance and they act as a flywheel.
In theory it's indeed 72hp, but there is a loss of power, either by the setup and by the clutch and gearbox. It will be interesting to measure the power output at the wheel! The job is incredible
As a mechanical engineer I think we should all celebrate the audacious, coloring-outside-the-lines ideas that the Garage 54 team thinks up and actually produces! Pure joy.
I think you would also like Rötger Feldmann's "Red Porsche Killer". It's a motorbike that's powered by 24 chainsaws. It's an idea from an animated movie by Rötger Feldmann and it was build in 1988. In the same year the bike had the first drag race against a red Porsche 911 at a festival just for this occasion called Das Werner Rennen. It lost the first race, but has since then also won at least one.
I couldn't agree with you more! These dudes always have some wacky and crazy ideas, yet almost every one works. These guys are awesome to watch. My favorite Ruskies!!
It’s the incarnation of this channel. “Why?” -it’s easy… no -it’s useful… no -you’ll be rich… no Because it’s S tier modification that nobody will do because all those no’s.
Anfang der 2000er gab es in Deutschland ein Motorrad mit 24 Kettensägenmotoren,selbst da waren die Fahrleistungen sehr bescheiden. th-cam.com/video/XDx70NVHlcM/w-d-xo.htmlsi=4DTXDNBgkwP-zx1k
This reminds me of Rötger Feldmann's "Red Porsche Killer". It's a motorbike that's powered by 24 chainsaws. It's an idea from an animated movie by Rötger Feldmann and it was build in 1988. In the same year the bike had the first drag race against a red Porsche 911 at a festival just for this occasion called Das Werner Rennen. It lost the first race, but has since then also won at least on.
@@ferrumignisit’s not a show car, obviously, so no point wasting time on proper quality. For proof of connect it’s ok. Most likely it’ll be trashed anyways, whole purpose is to show it to you that it works, imagine how much it cost them to achieve what you just saw already and TH-cam doesn’t pay anything in Russia since 2022 .
Its two stroke you cant just use any pipe. It works good only with proper backpressure by original muffler or by special tuned resonator exhaust. But they used original chainsaw exhaust on each engine which should be absolutely ok.
This is true on the exhaust..but if you’re talking about a standard banana pipe like they sell for bicycle engines it really doesn’t do much.. they do however make bigger around ones called buffalo bananas or something like that that are a little bigger on the chamber.. unfortunately true expansion chamber exhaust pipes are kinda pricey..currently looking for an affordable one to just make my own pipe with 😂
You Guys did Stellar, I Love this and I'm seriously Impressed. Comparing it to a 1976 Lada which goes 0-60 mph in 16.6 seconds and You Guys did it in 23.0...6 more engines should put You close to 14.7 seconds... Your torque I think is around 64 lb-ft which puts You under a stock Lada's of 85.56 lb-ft...A true feat of engineering. You Guys used 16 separate air cooled 2 strokes, totaling 928cc... A huge V16 chainsaw engine that is 641 less cc's than the Lada's 1569cc 4 cyl.4 stroke, nearly duplicating the Lada's original performance, that is unreal...Plus the ability to replace just one engine without a complete engine overhaul.. Bol'shaya Lyubov' Garage 54...🇷🇺🇳🇴🇺🇸😁👍🏻👏🏻🏆🏆🏆💜💜💜
They need a CVT transmission that can keep those engines at top RPM all the time because the torque at low RPMs is basically zero. Making an exhaust system would also be neat to get the smoke out of their faces and maybe reduce the noise a little (or make it more pleasant. The microphones were begging to stop 😂) Nice project. Worked much better than anyone could expect
If they had expantion pipes like a dirt bike y'all know they will make tons more power and if you could keep them at high RPM with a stall converter it would help a lot
@@ricktroxell6448exactly what I was gonna comment if I didn't see someone else lol💯🙏🏾😂 a proper tune with expansion pipes they could LITERALLY double the power output both horsepower and torque.
Nah they just need a 2:1 gear reduction... those chainsaws are easily running twice the RPM of the stock engine maybe 3-4 times. they do the same thing on many airplanes now that have higher RPM motors but need more torque for the prop.
The thing I’m always impressed by isn’t so much the contraptions but it’s how clean everything is always done. Like it’s always really fine craftsmanship
This reminds me of Rötger Feldmann's "Red Porsche Killer". It's a motorbike that's powered by 24 chainsaws. It's an idea from an animated movie by Rötger Feldmann and it was build in 1988. In the same year the bike had the first drag race against a red Porsche 911 at a festival just for this occasion called Das Werner Rennen. It lost the first race, but has since then also won at least on.
In an age where cars have become $80,000 NannyPads with wheels I think the last true petrolheads are guys like these in Russia. This absolutely reminded me of the sort of hare-brained shenanigans we saw in early Top Gear and I love it!
That rebar common shaft is cool. 70 hp out of less than 1 liter is impressive. Add some exhaust pipes. 2 strokes need a good exhaust pipe to help with flow and oower.
Chainsaw exhausts have rectangular shaped resonance chambers. They are not as efficient as the pipes on motorbikes but not as terrible as running the engine without an exhaust at all.
This might be the most satisfying sounding underperforming engine ever created. something about it sounds buttery smooth even if only moving at a comfortable pace compared to the drag strip
It’s practically a 2 stroke McLaren. Edit: I was wrong, Bugatti has the V16. I don’t pay much attention to stuff I’ll never own & thought it was a McLaren, my bad everybody
@@Sithhy you’re right, I was thinking of Bugatti.👍 Bugatti, McLaren Lamborghini, Ferrari…might as well be the same as a rainbow with a pot of gold to me. Once a car costs more than 20k, it’s fantasy land 😂
I love your videos. Great work guys. My favorite one is the video about the engine oil level. Keep it up. Best channel of all time. Greetings from Germany.
I would love to see a proper intake and exhaust manifold for this engine. The extended lada looks good too, they even fabricated and painted the panels.
A proper exhaust manifold would help with the power, as these are two stroke motors. Maybe they could add an electric leafblower to act as forced induction? :)
@Stoney3K I was worrying for the cylinders closer to the transmission the whole time. If they put a hood on that car without cooling duct, the engine will seize for sure.
@@HotGritz910 That is real fabrication How they assembled those chain saw engines together in one unit and got them synchronized and how they adapted it to the car's drive line , Amazing and how they did all the other modifications , One thing that was lacking was proper cooling for the engines because air cooled engines are shrouded to direct cooling air to the engine coming from the flywheel which doubles as a cooling fan and exhaust piping , but anyway , What they did was amazing I'll bet they can build a better car from scratch than you can buy at the dealership Just after I graduated from high school One time in my neighborhood I saw the metal shop teacher and his friend built a hybrid van from scratch which had a lead acid battery pack and a gas powered generator with a high amperage charger to keep the batteries charged to go long distances and was really cool , I don't know when it was ready for the road until about 3 months later I saw it going down the road Whenever they would park to go shopping or something else , They'd leave the generator running to bring the batteries back up to charge
Just a thought, maybe try setting all the engines at tdc, then linking them to the drive link bar so they are on the power stroke together at the same time. Also, that solid steel drive shaft must be really heavy, soaking up power. Maybe a tube would be better? Love this build!
Now it is time to make a V16 out of two 7 liter gasoline V8 engines and put it in the big engine bay. If you have the budget, maybe two put together two GM 632 cubic inch V8's into one V16 for the Lada.
I don't think there's many of these in Russia. The cheapest and easiest to get V8 in Russia should belong to old trucks/buses which are too massive and produce far too little horsepower to be worth it..
@@gabrielv.4358 The Moscow police did buy some Crown Victoria cruisers at one point. They were too big to fit down a lot of old world small roads in town.
If I am late for work and my car engine has died I will remember I can make a 16 cyl engine out of my 16 chainsaws I have laying about at a pinch. Thanks so much for this !
Garage 54 where clickbait isn't clickbait
under rated comment
WhistlinDiesel would like to know your location
😂 "sounds about right"
There’s no Russian word for
Clickbait!!🤭
Call it Sawdust or Chainsaw
Massacre!!🤭
From what I've found those chainsaws should be putting out roughly 4.5HP each. Total of 72hp. Chainsaws typically have a rev ceiling of 12-14k RPM. Probably double that of the original Lada motor. You could change the pulley diameters around on those timing belts. Give it a 2:1 gear reduction. Your output rpm would be 6-7k and the torque would be double.
Lets go people like this comment
This is the way.
Your main power transfer shaft is way too heavy to get up to that RPM number, so a 1:2 gear reduction is needed.
The neatest way to do it is to remove the pulleys altogether and install actual gears. Would probably be easier to balance and they act as a flywheel.
comment that on the original channel in cyrilic / russian also
In theory it's indeed 72hp, but there is a loss of power, either by the setup and by the clutch and gearbox. It will be interesting to measure the power output at the wheel!
The job is incredible
i doubt that these engines have 4,5hp more like 3 or less
now make chainsaw from lada engine
I would love to see that 😂
I would love to see that 😂
Gotta see that one!
Now THAT would be interesting
I think ive seen one made from a chevy or ford v8....
As a mechanical engineer I think we should all celebrate the audacious, coloring-outside-the-lines ideas that the Garage 54 team thinks up and actually produces! Pure joy.
I think you would also like Rötger Feldmann's "Red Porsche Killer". It's a motorbike that's powered by 24 chainsaws. It's an idea from an animated movie by Rötger Feldmann and it was build in 1988. In the same year the bike had the first drag race against a red Porsche 911 at a festival just for this occasion called Das Werner Rennen. It lost the first race, but has since then also won at least one.
I couldn't agree with you more! These dudes always have some wacky and crazy ideas, yet almost every one works. These guys are awesome to watch. My favorite Ruskies!!
As a guy watching his phone, I agree
So you support russians ? If so - your just another canonfodder to send
Many have propably wondered why there wasn't 1 liter 2-stroke V16 option available... well, now we know why! Cool project 👍
I think it's called a 'Laaaada' now
Or a ladaaaaa if you're standing on the other side
Ladatti
the Long-da
What about a LLLLada (because the hoods long)
How about Law-T-Daaaaaaaaaaaa!
26 seconds to 35mph... Incredible. I love this channel
It’s the incarnation of this channel.
“Why?”
-it’s easy… no
-it’s useful… no
-you’ll be rich… no
Because it’s S tier modification that nobody will do because all those no’s.
@@KhaoticKalmit basically boils down to "it's funny" and "because we can", and i love that about this chanel
Probably still an improvement of the standard Lada.
Anfang der 2000er gab es in Deutschland ein Motorrad mit 24 Kettensägenmotoren,selbst da waren die Fahrleistungen sehr bescheiden.
th-cam.com/video/XDx70NVHlcM/w-d-xo.htmlsi=4DTXDNBgkwP-zx1k
@@52Quantum This motor would look great on a stretched motorbike.
16 cylinders and still not a full liter of displacement, I love it❤!
How about those miniatyre engines, 12 cylinders and only 50cc
Smallest true v16 i have heard of is a supercharged 1.5 litre from the 1950s.
This reminds me of Rötger Feldmann's "Red Porsche Killer". It's a motorbike that's powered by 24 chainsaws. It's an idea from an animated movie by Rötger Feldmann and it was build in 1988. In the same year the bike had the first drag race against a red Porsche 911 at a festival just for this occasion called Das Werner Rennen. It lost the first race, but has since then also won at least on.
Idk man, my chainsaw is 200cc and it's a regular chainsaw. Nothing fancy. A friend snagged a v2 650 cc stihl that wasn't selling.
@@SoulTouchMusic93 pretty sure you have an extra zero in those numbers. A moped engine is already 50cc, 650cc is a big motorcycle engine
The level of craftsmanship these guys produce is absolutely astounding.
Did you see how wonky the steering shaft was after they extended it? 🤣
@ferrumignis a perfect example haha 😂
@@ferrumignisit’s not a show car, obviously, so no point wasting time on proper quality. For proof of connect it’s ok. Most likely it’ll be trashed anyways, whole purpose is to show it to you that it works, imagine how much it cost them to achieve what you just saw already and TH-cam doesn’t pay anything in Russia since 2022 .
@@Logic7repair Correct, so the 'level of craftsmanship " is very much not astounding, which was my point.
A quality job ". Fit for purpose at minimum cost " . What more could you ask for
The translator is really doing a great job.
The long lada is really cool looking honestly, and could fit all sorts of big engines in it. Hopefully this is a testbed for future experiments
Длинная лада выглядит как длинное говно, в отличие от обычной лады которая выглядит как обычное говно
really good looking proportions. makes me think of a jensen.
@@rotteneffekt4416 Reminds me more of a Bristol 412/Beaufighter.
probably they'll be up for something crazy because of this build yeah lol
Next find a Merlin engine 28 litre or a Gryphon 34 litres 😊
Having the right shape of exhaust is very important to two stroke engines. Buy 16 banana pipes and cris cross them.
Remove 2 engines and replace with 2 lead fly wheels and some torque should reappear...
i was thinking about the exhaust problem as well
true
Its two stroke you cant just use any pipe. It works good only with proper backpressure by original muffler or by special tuned resonator exhaust. But they used original chainsaw exhaust on each engine which should be absolutely ok.
This is true on the exhaust..but if you’re talking about a standard banana pipe like they sell for bicycle engines it really doesn’t do much.. they do however make bigger around ones called buffalo bananas or something like that that are a little bigger on the chamber.. unfortunately true expansion chamber exhaust pipes are kinda pricey..currently looking for an affordable one to just make my own pipe with 😂
As someone who once took a leafblower on a kayak, I approve of this video.
Haha! I bet that worked pretty decently!
Next time.
Try 16 leaf blowers 😅
@@fastinradfordableTHINK of the sheer performance
@@BotulinSpikedMarzipando you mean insanity
@@MR.JUSTCOD it's only insanity if you don't try it.
You Guys did Stellar, I Love this and I'm seriously Impressed. Comparing it to a 1976 Lada which goes 0-60 mph in 16.6 seconds and You Guys did it in 23.0...6 more engines should put You close to 14.7 seconds... Your torque I think is around 64 lb-ft which puts You under a stock Lada's of 85.56 lb-ft...A true feat of engineering. You Guys used 16 separate air cooled 2 strokes, totaling 928cc... A huge V16 chainsaw engine that is 641 less cc's than the Lada's 1569cc 4 cyl.4 stroke, nearly duplicating the Lada's original performance, that is unreal...Plus the ability to replace just one engine without a complete engine overhaul.. Bol'shaya Lyubov' Garage 54...🇷🇺🇳🇴🇺🇸😁👍🏻👏🏻🏆🏆🏆💜💜💜
Idc what no says this Chanel is pure gold on content and I’m from the Bahamas 🇧🇸
They need a CVT transmission that can keep those engines at top RPM all the time because the torque at low RPMs is basically zero.
Making an exhaust system would also be neat to get the smoke out of their faces and maybe reduce the noise a little (or make it more pleasant. The microphones were begging to stop 😂)
Nice project. Worked much better than anyone could expect
If they had expantion pipes like a dirt bike y'all know they will make tons more power and if you could keep them at high RPM with a stall converter it would help a lot
@@ricktroxell6448exactly what I was gonna comment if I didn't see someone else lol💯🙏🏾😂 a proper tune with expansion pipes they could LITERALLY double the power output both horsepower and torque.
The Robot Cantina method 🙃
Nah they just need a 2:1 gear reduction... those chainsaws are easily running twice the RPM of the stock engine maybe 3-4 times. they do the same thing on many airplanes now that have higher RPM motors but need more torque for the prop.
@@LongPeterthis is the way
The thing I’m always impressed by isn’t so much the contraptions but it’s how clean everything is always done. Like it’s always really fine craftsmanship
Yeah, string for the throttle linkage is a prime example of fine craftsmanship 😂
It's a food-mixer in Nigeria. Next week 16 hamsters.
😂😂😂😂😂
I like the turned rebar for the throttle linkage. Use what's laying around.
If you're going to do something stupid, do it right.
1:46 Running 16 chainsaws with NO hearing protection? Maximum Russian!🤣
They're Serbian I believe XD
@@Chazzy_tomatoes What gave you that idea? They are Russian
@@mykolastrunce5457 oh damn I swear I saw a comment or heard them say they were Serbian, my bad
this dude welds with no eye protection so thats benign as far as safety concerns go here.
WHAAAAAT!
😂
This prototype sure is a thing of beauty! I can't wait for production to begin!
This is one of the best channels on youtube. love it. great build. very fun to watch and no silly music or time wasting. great job
Love the stretched front clip, such a hot rod
Yeah, looks cool. Needs a V-12 now.
@@geraldgrieve41064 less cylinders yeah no
@@geraldgrieve4106it has a v16
With the long bonnet the profile reminds me of a '60s Mustang, but 4 door
@@shaneeslick I was thinking more like Mk IV Zephyr
I thought the SpaceX Starship flight test 5 was one of the greatest feats of engineering in human history, but this is going it a run for its money.
But this is actually real!
garage54 has better engineers
Well this isn't CGI so that's a plus
@@Romoto131I have so many questions but I'll refrain.
@@Romoto131 only stupid people think SpaceX launching Starship into space isn't real
You guys are crazy in the nicest possible way! Thank you so much for sharing your mechanical adventures with the world. 😀
This reminds me of Rötger Feldmann's "Red Porsche Killer". It's a motorbike that's powered by 24 chainsaws. It's an idea from an animated movie by Rötger Feldmann and it was build in 1988. In the same year the bike had the first drag race against a red Porsche 911 at a festival just for this occasion called Das Werner Rennen. It lost the first race, but has since then also won at least on.
This remind me a little bit at the red Porsche Killer from Germany awesome greetings from Germany 🇩🇪👋
Love the effort you put in to make the extended front end look nice.
If the apocalypse happens, i wanna be stuck with these guys
So do they. You will make many meals.
When, not if.
Yeah but they won't want to be stuck with you! 😂
Garage 54 guy: *"aaaooOOOOOaaAAoooOOhhHHH... WWWWOOOOAAAAAHHHHAOOAOOH!!!!!!"*
BMI Russian: "we are moving."
Hearing all those chainsaw engines harmonizing was awesome. Iam going back to your older videos to see how you got there
out of all of the insane builds you could do with a lada this is definitely in the top 5
I love the proportions with the longer fenders.
This is such a gloriously insane project.I absolutely love it.Keep up the good work guys
I have over 50 weed eaters and think about this stuff You put it into reality! Thank you! Your channel is growing fast! Awesome job.
Build an awd go kart or 2 wheel drive bike
Bros life is a word problem
I prefer Smoking it than eating it lol
How do you have 50 trimmers????
@@SHAGG13
Can't mix 2 cycle 😂
In an age where cars have become $80,000 NannyPads with wheels I think the last true petrolheads are guys like these in Russia. This absolutely reminded me of the sort of hare-brained shenanigans we saw in early Top Gear and I love it!
You guys always look like your having a good time! I'd love to chill with you guys in that garage!
first time I seen someone use rebar for throttle linkage ... NICE!
The execution of fender extensions is beautiful :) The car looks so cool 😎
Good stuff!.....Those 2-strokes love to be run hard.....Keep them up in the rpm range and they will come to life.
Yeah I was wondering why he went all the way to 5th gear when only doing 60kph.
@@ProgramentalistHe was scared of it.
Thought a fight would break out among them!!🤭🤛
thats the silliest shit i have seen in a long time you silly buggers. rad. thanks for existing.
The Lada looks so good stretched! Your craftsmanship is on point
It would be much more prettier would they cut it to be a coupe. Making it a pony-lada. No, donkey-lada.
That rebar common shaft is cool. 70 hp out of less than 1 liter is impressive. Add some exhaust pipes. 2 strokes need a good exhaust pipe to help with flow and oower.
Except that a 1,000 cc twin cylinder two stroke engine will make 165hp easy.
Shit my 6cyl 1500cc mercury tower of power is tuned out to 225hp with just reeds and jets and a drilled crossover plate
You're correct but that isn't really the point; this is cooler. @@adamdice231
Chainsaw exhausts have rectangular shaped resonance chambers. They are not as efficient as the pipes on motorbikes but not as terrible as running the engine without an exhaust at all.
Bloody love a TOP @@79huddy
Russian automotive mythbusters isn't something I knew I needed, but I'm so glad it exists.
These guys do some incredible work. One of the most creative channels on TH-cam!
That’s awesome! I really like the fabrication on the body extension matching the lines of the original fender. Keep it coming G54!
Theres so much soviet engineering in this that i LOVE it.
Reminds me of the beast with a Merlin installed.
More engine than car!
With about 1/84 less HP.
that thing also had more displacement in a single cylinder than this whole thing
I think that's can be registered in the Guinness record for an 1.0l engine with the most numbers of pistons.
This might be the most satisfying sounding underperforming engine ever created. something about it sounds buttery smooth even if only moving at a comfortable pace compared to the drag strip
The fact that they got it to look like an actual car is just as impressive as the engine built itself. It’s so clean.
Damn, these are the ideas i have when i am high
Same with them?
How many Ladas will they have for each experiment? 😅
eventually, this channel alone will use up all the ladas ever made
@@ThePurificator69420 You know, there are still so many old Ladas here... There's no way they'll experience any shortage in the near future.
It's such a good signature for g54
They will bring the old mighty lada back in production!
Unlimited bro. Because Russia
Now I actually want to see this as a full fledged engine. Great work guys.
It's truly amazing how all their videos seem like clickbait but the titles and thumbnails are purely factual
For some reason I really like the look of that new front. I think it would look absolutely awesome with some proper engine and finish.
Old school American straight 8 cylinder!
What an amazing channel, not an ounce of clickbait. Every. Damn. Video.
...our favorite cRaZy Ivans are back with another winner...
Garage54, where the test mule is always a Lada!
And I wouldn't want it any other way.
These guys are revolutionaries in the "F#%$ing around with cars" category.
That went so much better than I ever expected.
Im never going to doubt garage 54 again.
It’s practically a 2 stroke McLaren.
Edit: I was wrong, Bugatti has the V16. I don’t pay much attention to stuff I’ll never own & thought it was a McLaren, my bad everybody
I don't think any McLaren came with a V16
Bugatti you mean perhaps?
@@Sithhy you’re right, I was thinking of Bugatti.👍 Bugatti, McLaren Lamborghini, Ferrari…might as well be the same as a rainbow with a pot of gold to me. Once a car costs more than 20k, it’s fantasy land 😂
@@SwapBlogRU yes, I knew one of those had it, just thought it was McLaren. You are correct though
That's cute asf lol it's actually Bugatti
I love your videos. Great work guys.
My favorite one is the video about the engine oil level.
Keep it up. Best channel of all time. Greetings from Germany.
I love and appreciate the fact that even for a joke they went the extra mile to actually finish the car
5:45 It's the Longda!
You guys always make me Smile . Great stuff . Cheers from Australia
Garage 54 Awesomeness!! Thank you guys!!
This channel never ceases to amaze me! Even after all these years. 😂
You Guys are AWESOME!! If Your Cannel isn't bringing you guys $1 Million Dollars a month, It Sure as Hell Should Be!
I would love to see a proper intake and exhaust manifold for this engine. The extended lada looks good too, they even fabricated and painted the panels.
Nah it has itbs right now lol
A proper exhaust manifold would help with the power, as these are two stroke motors. Maybe they could add an electric leafblower to act as forced induction? :)
Cooling duct would also be a pretty good idea.
@Stoney3K I was worrying for the cylinders closer to the transmission the whole time. If they put a hood on that car without cooling duct, the engine will seize for sure.
@@Stoney3K Ja unter dem Auto von der Front da wo Überdruck ist in den Unterdruckbereich hinten am Auto.
“I see this as an absolute win” 😂👍 me too
Usually you guys are doing some really dumb stuff...but this time, pure genius!!!
btw...Lada looks mean as hell with her hood extended 😮
it’s official you’re a genius all the mad dreams I have at night you bring to the day thank you for posting and sharing your skills
It just gets better & better- Ingenius guys - Thanks very much for all the great content !!!
This vehicle should be called the Borzoi
The snooooot
Hosegoat!
This is one of the best channels on TH-cam. These guys display a very high level of skill, mechanics, and engineering. Amazing!
I think you’re going a bit far to say that they are the best on the platform but in their genre they are definitely up there with the best
@@HotGritz910 That is real fabrication
How they assembled those chain saw engines together in one unit and got them synchronized and how they adapted it to the car's drive line , Amazing and how they did all the other modifications , One thing that was lacking was proper cooling for the engines because air cooled engines are shrouded to direct cooling air to the engine coming from the flywheel which doubles as a cooling fan and exhaust piping , but anyway , What they did was amazing
I'll bet they can build a better car from scratch than you can buy at the dealership
Just after I graduated from high school
One time in my neighborhood I saw the metal shop teacher and his friend built a hybrid van from scratch which had a lead acid battery pack and a gas powered generator with a high amperage charger to keep the batteries charged to go long distances and was really cool , I don't know when it was ready for the road until about 3 months later I saw it going down the road
Whenever they would park to go shopping or something else , They'd leave the generator running to bring the batteries back up to charge
@@feelincrispy7053 I'll bet they can build a better car from scratch than you can buy at the dealership
Except the stupid overdub.
Stretched lada looks so good
this istheonly channel where i like the videos before i even watch them because i already know they are going to be epic
Amazing experience!! You guys are awesome! Would love to see similar builds with other engine types and sizes!
Been waiting for this moment for an entire week! Thanks lads
let the madness begin
Obviously theres enough space for a W32 engine in there.
No X32 not W32
Garage 54 has stepped up their game! Cool video.
Stroker kit and twin turbos when? 🤞
After a long wait
8:21 It's not a 16 cylinder engine, it's a 16 engine engine. 😁👌
Lmaooo
This is gonna be a good one
Okay this channel is insane! Thanks for this guys, this was pretty cool.
Just a thought, maybe try setting all the engines at tdc, then linking them to the drive link bar so they are on the power stroke together at the same time. Also, that solid steel drive shaft must be really heavy, soaking up power. Maybe a tube would be better? Love this build!
I hope they do tuned pipes eventually !!!
Thank you, great work.
Up next, we take this to the next level with the installation of 16 tiny turbochargers!
I would just install two "big" ones. Turbos are pretty hard to keep spinning with that tiny displacement.
You all look like you are having much fun 😄. Good for you! Greetings from 🇩🇪.
This is awesome im glad you guys managed to get it working. One of the best videos yet 🤙🏼🤙🏼
¿Cuantos Ladas tendran para cada experimento? 😅😅😅
Now it is time to make a V16 out of two 7 liter gasoline V8 engines and put it in the big engine bay. If you have the budget, maybe two put together two GM 632 cubic inch V8's into one V16 for the Lada.
I don't think there's many of these in Russia. The cheapest and easiest to get V8 in Russia should belong to old trucks/buses which are too massive and produce far too little horsepower to be worth it..
there are no american things in russia
@@gabrielv.4358 They do have some semi trucks and SUVs, but yes, those are rare.
Dude those engines are heavier than the car.
@@gabrielv.4358 The Moscow police did buy some Crown Victoria cruisers at one point. They were too big to fit down a lot of old world small roads in town.
@Garage 54 , Name it "The Centipede" 👍
You need to make headers for the exhust and bolt on 16 expansion Chambers on the exhaust so the engine produse some torque and power
I thought youtube it's done in Russia. Well.....I'm glad you guys still find some ways to upload and do some money.
"Maaaa, the neighbours are doing wierd shit again!"
Russia, rushing to do weird shit.
Keep working on this! Lots of room for testing and refining the vehicle to improve this prototype into at least a functional grocery getter.
If I am late for work and my car engine has died I will remember I can make a 16 cyl engine out of my 16 chainsaws I have laying about at a pinch. Thanks so much for this !