วีดีโอ

I have 2006 jacuzzi j335 2006. Where do i get parts to replace flow switch, heat sensor and circulation pump? We just purchased . It was supposed to be in good working order. It was not. When we filled it up all pumps worked but it was leaking from the tube coming out of the black box hooked behind the pack. We fixed that then got error code. The black box is the heater?

You just helped a very confused norwegian. Thank you.

Thank you for this! About to go outside and attempt to find my leak now. This is EXACTLY the video I was looking for to help me out! Subscribed!

I have changed out the hot tub and the pack is farther away from the end of the original seal-tight tube. Can the wires and the seal tight tube be extended?

excellant video thank you for posting

The plunger worked!

Hi Scott. Got a bullfrog spa that sat for quite some time. Had a repairman come out and he said bad pump/crack from freezing. We replaced pump, and cover. Now the tub is leaking and the power is tripping to the tub. He is recommending heater replacement next and no guarantee it fixes it. The power trips to the breaker after about 5-6 days so when he goes to test things he can’t find anything. Have you seen this issue where is trips after 5-7 days and then leaks out. Thanks

Hey Scott, I have the same problem (the same light). The local jacuzzi shop says the part is not available. Can you send me the link to this part? Thanks. Your video are great. Keep them coming!

Just purchased a dealer refurbished j325 with all new internal components but guess where they decided to cut corners..6 of the spinner jets (7 total rotating jets on older j325). Instead of replacing them, because I'm sure the bearings failed, they just yanked the bearings and housing out so it was just plastic flopping around inside the jet. I went down and told them I have 6 bad floppy rotating jets and they said they're supposed to rotate and I said YEAH ON A BEARING LOL. You should've seen the look on their face when I pulled the 1 good rotating jet and 1 bad rotating jet as an example out of my hoody pocket. They said they'd be over to replace them...man, can't even avoid funny business from a local dealer. Wish everyone could be honest like Spa Man!

Why not just cut in the middle of the pipe and put in a coupling then the elbow. I cant imagine wasting all that time not to mention that youre now risking having the pipe leak after completion...

Just fixed mine by simply unplugging the ozone within a few minutes thanks to this video!

Another great teaching video!!! Thanks

Great teaching video, but I'm confused why you emptied the hot tub when you could have just closed the gates.

Great video, thanks. Can you bury the liquid tite conduit and run it up underneath the spa and through the base of the hot tub to just outside the spa pack? Or must you come in through the bottom section of the side panel of the spa (i.e. come in through the side of the spa vs up through the base) and feed the conduit/wire through to the spa pack? Are there knockouts on the side of the spa where you would insert the wire cable conduit for this purpose, or is it "drill your own?" Thanks

You just saved me arse!! Thanks so much. I restarted the tub, cycled the pumps, bled the lines and I don't think I have a bleed valve. Nothing worked. I'm also in Canada so I was very worried about freezing. Then came your plunger idea!!!! It's first if there's a next time.

why are you replacing all these valves? I mean aren't they serviceable like a new stem/plunger or o'rings. That's where I'm at on my tuff-spa the 2" orings are shot so I'm hoping to replace those and put it back together. Is there something I don't know. Not a pro here. Thx

Can I ask for your help I have that ht tub. But I have had to put a new pump heater and control panel how do I make it plug and play I am based in the uk.

You explain this incredibly well

Great video, thanks very much. The flexible conduit packaging at my Home Depot (product: Ultratite Liquidtight Flexible Non-Metallic Conduit) says it can be buried (suitable for "direct burial"). Is this not true?

California it's legal to put colored tape on black wires over a certain size, people just buy the right color of wire and be done with it.

Spa man glad to see another upload!

Super helpful and straight to the point. Thank you!!

OK, spa guy had I just listened to some of your other videos about the GFCI. It would’ve saved me a lot of troubleshooting. I connected the neutral to the spa to the neutral bar instead of the GFCI rookie mistake. Your videos saved me.

Hi Scott, I have a Jacuzzi bathtub with an air lock. Every time I fill the tub and turn it on the pump starts but no jet flow. I have used a plunger over one of the jets and I am able to get the jets going. is there a way to figure out where the air lock is coming from? I have also tried using some spa stop leak with no luck. Any ideas? I have left the tub full of water for a few days after getting it working and the jets will start up right away. Thanks for any help.

But what if just one wire at T-B1 trips the gfci ? After unplugging heater and the other components

that is my hot tub exactly...J-325....replaced pillows, waterfall, heating element, pump and 2 covers in 10 yrs....it is a nice tub but it can be a money pit after all the years plus the initial investment

Where do you purchase those parts from?

I have. Balboa v 500 it was heating to 100 it popped ireset now only heats87 please help

my guess is finding the leak is the worst part...not looking forward to it, thanks

Amazing amazing thank you sir!!!!

Spa Man..... Dude your videos are a life saver. You have saved me so many times from pissing away a bunch of money or time troubleshooting. Keep up the good work, your hottub content is priceless and I seek you out over anyone else. Make more repair videos as there is nowhere near enough hot tub repair videos on the web. Considering all the various models its hit and miss. Everyone always seems to be so intimidated about repairing their own tubs. Your light hearted videos remove that intimidation factor. Appreciate you.

Resetting hot tub did take care of the issue. Thank you

Thank you for the information however the hat and glasses indoor while leaning into the camera makes you look 🤪

Does the feed breaker (to SPA panel which is GFCI protected) ever have to be GFCI in the main panel?

Good job .I Bought a new Spa had the electrical 220 hooked and breakers But wanted to know how to prime it first start up So now after you showing i will fire it up! TKU!

💪😎🔥🔥🔥🔥🔥✌️🙏 thankx for your videos couch!!

Yes, I'm a hot tub tech too, that is good 👍 You can also go in the front spa cabinet and release the airlock that way as well through the pump itself or intake pump union. Nice, I'll have to try the plunger method, I'm so used to releasing it from the pump, thanks! 👌

Great job electrician is going to Connect Mine next week He's got already number 6 wire all the way coming from my breaker box. 75 feet to my backyard. I can already do it from here. I am not a electrician But I have been working with this stuff for a few years so I know When it comes 220 and water I want to make sure some license electrician does it But I already paid him to do it!! Brand new jacuzzi. Lol!!

Hi. We have some issues of balboa jakuzzi. The main board is working, but the little bubbles not coming through water, also there is over heating sign shows control panel. Please help us to fix it.

Hello i want to fix my issues of balboa jakuzzi. There is no little bubbles coming through the water. Please help me to solve this

I have a caldera vanto spa and it is air locked and nothing i do will fix it. The plunger trick wont work on mine of course because the caldera has a tube that comes up in the filter. So im still searching for a remedy.

Spa Man you're the best! Straight ahead. Here's what you have to do, just do it and no BS. Thanks a mill. The world needs more people like you!

Finally, someone who knows how to make a *How-To* video 🤙 appreciatory valve wide open

That is an old auto body file for shaping the lead seams on older cars

Excellent explanations bro

I’m trying h to find a replacement light for our 2005 Accolade Hot Springs Spa that has a Luminesence Multicolor Set up …it’s an obsolete item and I can’t find one….any help ?

I don't do anything when I refill it. And I use a shop vac to empty all the piping when I drain and refill. Never had a problem in 17 years.

My Artesian spa has 4 individual pumps. I just finished using a spa system cleaner and was using my shop vac to clean. Now i have just 1 pump i guess has an air lock. I suppose i would have to got to the pump and release the air somehow?

What tools (and size) do you use to remove the jet? 1:17

What tools do you use to remove the jet?