Water leaking on the Motor & Pump (NOT GOOD).....How to fix a leak in a Hot tub...EZ fix
ฝัง
- เผยแพร่เมื่อ 16 ม.ค. 2025
- Hey Everyone Hope you all are doing well ,
The home owner had a sizable leak and the water was leaking on the pump & motor ...This had been leaking for some time now the pump and motor were just replaced because of the water dripping on it over time. It only took a few hours and as you can see its real not that hard of a task.
As always Thanks for Watching & SUBSCRIBING
And PLEASE do not stick your hands inside ANY Spa or Hot Tub until YOU yourself see and shut off the Breaker..I hope I made myself CLEAR.
Do you want to purchase something seen in this video? Consider checking out my Amazon Associates page and find all of the gear I use + everything used in this video!
----------//My Gear\\---------
GoPro7 Black...amzn.to/3tOI7WH
128 SD Card...amzn.to/3tRnw4i
Vivitar VPD-360 Tripod...This Product is very old... Can be found on EBAY
Joby Mic...amzn.to/3H7oljD
---------//Parts\\---------
NOTE*** Make sure the part fits your model***
Jacuzzi Filters J300 Series 2 Pack...amzn.to/2QDKzSi
Jacuzzi flow switch...amzn.to/3dvAfEJ
Jacuzzi Heat Sensor...amzn.to/32xdZEk
Jacuzzi Circulation Pump...amzn.to/3cVjUvs
Best Cleaning Product...amzn.to/3S4k6up
---------//Other videos that will help You with Spa/Hot Tub Wiring\\----------
(1) Wiring a Main to Sub Panel... • How to wire from the M...
(2) Wiring a Sub Panel... • How to wire a Hot Tub ...
(3) Wiring a Spa Pack... • How to wire a Hot Tub ...
--------- // Tony Stark Tool Kit \\---------
Milwaukee Tester...amzn.to/3wew8DH
Little Giant Pump...amzn.to/3egugD4
This product will Clean all the inner hoses & Tubes...amzn.to/41EHrpD Its a must use.
Please LIKE , SHARE & Subscribe
---------------// LEGAL TALK \\ ------------------------
I get some funding via your transactions with purchase links with the following affiliate programs.
Amazon Affiliate.As an Amazon Associate, I earn from qualifying purchases.
⚠️DISCLAIMERS:
FTC: Some of the links above may be affiliate links. If you purchase products with these links, I will receive a small commission at no additional cost to you. Thank you for supporting small creators!
FTC: This video was not paid for by outside persons or manufacturers. No product was supplied to me for this video.
As always Thanks for Watchings & SUBSCRIBING.
How to wire a Hot Tub
Spa
Hot Tub
Wiring
Subpanel
electrical
Balboa
Jacuzzi
Spa Repair
wire spa hot tub
DIY
Arizona Hot Tub Factory
Hot Tub trips Breaker
wiring GFCI 50 Amp Breaker
#6 THHN
four wire Hot Tub
Spa Heater
electrical install
electricity
Sub Panel
main Breaker
wiring a Subpanel
Head cushions
Spa Cushions
Bullfrog hot tubs & Spas
You are the sound of freedom!
You by far have the best hot tub repair videos on the internet. Thanks for all you do.
Thanks for your videos and your great advice about spas!!
You are correct .. Thank You
#spaman5440 Hey Scott👋 Chad from Milwaukee’ish WI w/ a 2003 Master Spa LSX1050 that has a couple leaky diverters (also over circ. pump now in-op)
. Luckily for we have RJS,
an awesome, father - son hot tub repair service who freely share advice Shade Tree mechanic, well I run a business making mechanical control cables I think this is my 3rd or 4th leaky diverters (also over 😢 pumpon a. Luckily we have RJS, an amazing, father - son hot tub repair service who freely share advice Shade Tree mechanic, well I run a business making mechanical control cables which requires a lot of setup & maintenance. The problem is how tight everything is even the techs didn’t want to replace, or remove / reseal, instead they planned to disable a neck waterfall so I pushed thee appt. off & decide to try fixing it myself. 2 questions:
1, How do you know when it just needs a seal kit vs. complete replacement?
2. Can you silicone / seal around the deck mounted flange
Now I think this is my 3rd or 4th video of yours I’ve watched and definitely learned a few great new processes, tooling tips etc. that I’ve liked each video I’ve watched, I. & subscribed As
I have 2 questions
To see what nLuckily we have RJS, an awesome, father - son hot tub repair service who also
freely share advice jShade Tree mechanic, well I run a business making mechanical control cables I think this is my 3rd or 4th
@@chadsalter9961 If I can not remove the diverter gate valve out of the housing That tells me it is no longer round or is out of round like an egg..and it will not seal up then it needs to be replaced
Or If you put it all together and turn on the spa and the water pressure blows the top off the diverter valve that tells me the threads will not hold the top on and it most likely will have to be replaced.
The problem with silicone or other sealents is you have to use them for what they are intended for..When you use them on the out side of a leak with the water pressure pushing out they will always leak
What ever product you use...You have to use it on the inside with water pushing out..and in most typical leaks this is very hard to. do.
Most leak happen because the joint or part was not installed correctly in the first place. and in that case it is best to just replace it with correct part and seal it up the proper way.
Hope tis helps Thanks for Watching & SUBSCRIBING
You gave me an idea for a video
@@spaman5440 Good deal, thanks for clarifying 👍🏼
Since we’re helping each other out, would you share your best techniques for removing the clear air lines that the manufactures tended to glue onto the jet housing / barb? What a chore those buggers are!
Oh & maybe you already covered this, I’m going to look in a second, how does a guy know if the ozone injector is working correctly? For that matter, any tips on matching aftermarket injectors, to new ozone generators, if they’re not sold together
Why not just cut in the middle of the pipe and put in a coupling then the elbow. I cant imagine wasting all that time not to mention that youre now risking having the pipe leak after completion...
There are always several ways you can do things. This is just the way I did it on this job. Thanks for Watching & SUBSCRIBING
Sorry if that came off a little harsh. Thank you for the video it was very informative. This method will be super useful on a special fitting you cant find like a special manifold.I learned from you thank you very much!! @spaman5440