วีดีโอ

Thank you!

When I see someone pushing in a contact just tells me. Your an orphan had angiogeno with an acerrar.The most serious size fix our angelo adinaWhen I see someone pushing in a contact It just tells me that he's never had one blow up in his face, Directions to levi to what he can first check for ground Before you push in any contact. Period.

Great great video bro watched a couple of these yours seems to be laid out very nicely and very informative thanks for posting

How much did you discount the bill after the client discovered the sink pipes were now clogged?

How did you get quest to respond to you im trying to service my 225 but I guess since it’s past 5 years old they don’t care about me ! After you drill out the rivets how do you pop them put

Great video..

I've been looking everywhere for this video. Thank you!

Good job 👍

I invented this tool, told the rights to Diversitech, and they produced it. I’m glad you are enjoying brother!!

Do you just break off enough fins to get to your leak area ? Do you replace it when done ? Also the r410a has high gwp and was reading that r32 is perfect replacement for r410a with only 3rd of gwp and slightly better efficiency. Can r410a be replaced with that in every unit ?

Thank you so much for this video! I'm going out to replace a fan wheel on a unit tomorrow and I've never done that before. Now I'm not going in blind!

What was your amount of time on site? I have 2 cassettes in a small/mid size kitchen that need stripping and cleaning, hardest part is the scheduling to lessen the impact on their business. I know production of the video adds some time for camera repositioning and narration.

It's too bad that you're in CO. I'm in a recently built building in NYC. The GC and subcontractors left all my Mr Slim and ceiling cassetes running during construction. The amount of drywall dust and filth in my units is absurd.

Can you do anden?

Great video. Thanks for sharing.

how long did it take😅

I’ve had good luck repairing condenser leaks. A relative called me one day and said his roommate accidentally shot the condenser coil with a .22 bullet. The local HVAC repair company refused to fix the hole. I was able to repair the hole by removing a couple inches of aluminum fins and splicing in some copper tubing.

very nice job.

what gauge is the metal?

Great video! :) First in depth video I’ve seen with a Quest unit! I noticed you didn’t remove your micron gauge when you went to recharge the unit. Is that okay to do? I have heard that the liquid refrigerant can foul those sensors in the gauges.

Awesome video

Wow! Amazing it was still working. Water treatment is so critical and yet constantly overlooked for some reason.

wow lot a work

Due to vibration that coil will leak again. Probably ok for a while given you're in Colorado and AC season is very short there. I've attempted these coil repairs here in my area they rarely last that long. Nothing to support the metal refrigerant tube on that one side that you had to remove to make the repair. Due to that those tubes will vibrate during operation and rub themselves a new leak. I get it that this is commercial and tenant is probably renting this space so much cheaper to attempt a repair than buy a new condenser coil as those aren't cheap. But if it leaks again in less than 2 years, it may cost you this customer because they view you as wasting their money. Something for you to think about.

great job!

Great job! Thanks for recording. 👏. I like to upsize my drier when possible when dealing with restrictions. Just like you would with burnout, you get more capacity to catch anything that may be left. Sometimes, if the oil is an issue, I've seen driers plug again after the initial repair.

I installed one with transducer and it seems to toggle rapidly between full and variable, is this normal operation with the transducer? Set at pressure and 300 psi

Show us how you got the fan wheel out I’m terrified I’ll wreck my mini splits lol

Thank you, saved me a ton of frustration lol

Worked in place with fabric duct. Never installed it before....this was a cool video

Do you guys do services in Michigan?

Try it with transducer.

BioTherm .... i need 1% shares in that company! That product is made for greenhouses! WOW!

THANK YOU!! Haven't been searching for this information everywhere.

Look at all the gimmicks

What gauge metal are you working with? I’ve never seen this tool before looks to be very useful!

JCI P266....while expensive....is probably the best one out there for fan speed modulation. The carrier headmaster is also pretty good as well....i really like the carrier temp probe that is a circular clamp style. Pro tip....use some thermal heat transfer paste too...gets a slightly better reading. A quick way to determine sleeve vs ball....a sleeve will have in and out play on the shaft...a ball won't

I am not a fan.....of fan cycling switches....Definitely prefer fan speed over cycling.....LAC valves are even better. Cool video

So how did that grow pass microbial testing 😂

I wanted to see how to get the blower wheel out.. this was not helpful

I would have to agree, I feel like many techs arent going to graph it out and make multiple adjustments?

Is this 3 phase Condense motor?

Excellent work

AI in cannabis growing is just information overload and not needed. This is not growing cannabis, no matter what you say

Fun event and great video!

We have that same rug lmao

Nice troubleshooting and work. Subbed.

Great work, guys! Thanks for the love and thank you for stopping by!

Dude, that is black mold. So nasty! How often is this kind of cleaning necessary?

Beautiful work