วีดีโอ

Thanks for sharing. Very Helpful !!

I hate replacing those batteries, the design is just bad.

What tool head / extruder is that ? My svo6 plus def doesn’t look like that 😂

I know it's 2 years later, but you can internally wire the usb by soldering a 4 pin header on the provided holes just under the usb port (s1 silent mb). Ground (black), data+ (green) , data - (white) and positive (red), which you wouldn't use. Hack a usb cord up to plug into the header and no more messy usb cord sticking out.

All my tools are m&p in love them with a passion however in my 45acp I’ve had a few mag springs give out on me 10rd mag I’ll get about half the rounds out then that’s it they won’t feed however the mags are roughly 7 years old I’m guessing it may be common I’m not sure , my Glock is much older and I’ve kept a couple mags fully loaded and never had that happen , anyways now I’m concerned about my shield it’s my daily ccw and obviously my life depends on it I love it but in the back of my mind the mag springs nags me it’s a concern , if anyone has experienced the same and or knows of reliable springs for full sized m&p and shield please point me in right direction? I seen some say extra power I’m guessing those are a bit longer or possibly thicker but I have no clue what to do

Such a cool project to see, you did a great job, I love it

Hi, I am interested in the extruder and motherboard position shifting mod. Is there any tutorial / references ?

Are you western MA?

Idk if you’ll see this, but do you remember if this had the factory resonators in place AND the Vibrants? Or just the Vibrants? Looking to do a similar custom setup on my Lexus, I already have a 1792

So far car has been great the exhaust note is interesting I half expected it to sound similar to a 2.3 EBM because the turbo is mounted to the head directly, but it doesnt, I think its because only the exhaust side of the valves are camshaft controlled, I believe the intake valves are oil pressure solenoid controlled or similar. It is a sohc engine so.

Car sounds good. When I had a 2020 Giulia TI with a JB4 Map2 tune, I was surprised that the car could outrun a 5.7L V8 Challenger. Wasn't expecting that.

Cool!

Niccccee 🔥 just got my guilia, looking to do the same thing soon!

What headers long or short tube?

Hi How did you wire in the toggle switch? Thanks

Is that a drawer under the printer? It looks so great. I've been looking for risers with drawer, I'd love to get the models for that one. Could you share them?

Bonsoir, je veux bien le lien amazon pour les moteurs nema 17 42TH40 high temp, merci.

Would be fantastic if you would post the adpater stl files. So others can build there own platform.

Sounds like you have the wrong driver's installed. It shouldn't be whining like that.

Nice! Looks like the part fan setup is much upgraded. I just designed a dual 5015 holder for the SV07+ (it's up on printables) and am figuring out how to adjust the cooling profiles for different materials. What ran fabulously on PLA is causing me grief on PETG - specifically too much cooling when overhangs take an inside turn. Any pointers? TIA

lipstick on a pig

that puppy is soo cute and naive T-T

Yea, you need to be printing abs at about 250

how did you get the bearings out of the Z axis? i wanted to replace mine but thought i would be need some kind of press and did not want to damaged the blue container shell plastic that is holding the bearings. any tips?

Motheboard 4.2.3 ? Or 2.4s4

Hi, do you know If I can replace original X and Y motor with LDO 0.9 steppers and keep using original board? Right now it's almost completely stock, I bought SonicPad for the klipper and I dont like how sovol's steppers sounds on higher speeds.

That mf sound like a str8 up Harley

betcha it doesnt print well

looks very good!!

Theseus’s SV06

Love this mod, just wished you would have gone with TAP. That's my only holdback on this one.

This is great! Do you have the plans for the risers you used to put everything underneath the printer?

Hi, How did you replace the linear bearings from the x and z axis? They are press fit really tight on my unit.

Hello! Great modifications, im in similar thought for my 06plus. I follow you on printables, would love for you to upload that Modified ender deck skirts it looks great!

Ok I confused on parts for Extruder and how to set and install everything? Works on svo6 plus right?

Awesome job! I'd love some sort of step by step instructions. Especially for the hotend/extruder rebuild. Did you have any issues with your left side of your bed showing way lower when auto bed leveling. I've tried everything I can think of and can't fix it

link to bearings?

So clearly.. they got the base plate they give you right? Its all that looks original 😂❤ I just got one and absolutely loving it Your one looks absolutely insane Would love to see maybe a video about each upgrade and close ups, maybe how tos ❤

If you don’t mind, what do you think is the most essential mod(s)? That is, which parts from the stock do you think are okay and which are unbearably bad?

Can you share the stealthburner mount STL? Love the upgrades!

hey, curious how you wired up the stealthburner. really interested in doing this mod.

Out of all of the upgrades, which ones are a MUST? Any help would be appreciated. I'm buying this printer and want to make sure it runs good

when searching for "LDO Nema 17 42TH40" the only one that shows up is "42STH40" is that ok to use?

How did you install klipper and BTT CB1 compute module(pi replacement)? Is there a video for that I can follow?

try to go tje lenear rail way , that will probably almost double the print speed since it will be much more rigid 🤷‍♂️

Did you do the 0.9 stepper upgrade? I am curious if it makes a difference.

Love it, good job!

It looks like you got rid of the Y axis linear rod holders / mounts. Is that right? Do you have an STL if you did? I am so sick of this printer breaking...and those Y axis mounts are super thin...I was trying to diagnose terrible banding....I bought Drylins and while taking it apart, I realized the mounts had snapped...this is after I had to redesign the X axis pulley and fix the extruder. I love the machine, but I can't stand where they took the cheap route.

Better printer than the 2.4 in every way except the default short build height but the 300mm kits are accessible

All it's missing is a better hotend imo