วีดีโอ

Did you attach the uppers to the lowers? Also, do you find yourself using thin felt tape or anything under those uppers as you install (as to not scratch the countertop)?

I've been using pressure pots for a couple years now and love everything about the set up. I only have the Fuji half gallon pot and Graco pro comp pot and gun but been looking at a bigger pot like that. So from your experience since having this set up, how fine of a finish can you achieve? Are you spaying Kem-Aqua plus? Have you sprayed any 2k, Conversion varnish or lacquer? I've been struggling with laying down a glass like mirror finish in CV, even after catalyzing,retarder & thinning. I enjoy watching this type of content and thought I'd see if there's any advice you could offer to my dellema. Nice set up, keep up the good work 👍

I can’t get mine to pull the tape through. Could the tape roll be too heavy? Maybe use a smaller roll. Please advise. Thanks

Not understanding the air hose connections. I see a yellow and blue air hose connected to the pressure pot. Can you expand on those connections?

Does this use the Fuji turbine and also a separate air compressor or just the turbine?

what fittings did you use?

Always drop your bucket on the ground before getting off any machine so it can’t move.

Good job , man !

I really appreciate your run-through of this machine. Do you tend to do a lot of frameless cabinets, or do you change between frameless and faceframe? I'm a one man band, but festool edgebanding is taking way too long.

What's minimum duble side panel thickness

Nolan you are amazing! Thanks for sharing all the important details and also this little things about the removable labels it’s awesome info, thank you again!

Great work! Where do you buy plywood?

Stoked I found your channel! I have a small shop as well. Learning Mozaik right now. Keep up the journey!

Really nice video! FS should use you for demos on the D6 (if they ever have one)

Impressive! You are very knowledgeable.

I see the appeal for large spraying sessions. The cleanup compared to the 3M PPS system is the only concern I would have.

Just found this video while looking at Mozaik. Thanks for sharing. You make Mozaik look easy and I love the labels, certainly needed when cutting so many sheets. I’m curious why you don’t use a spoil-board to limit any damage to the machine bed. Also, your dust collection needs to be stronger. I have a 2HP system with 4” hose and it sucks up EVERYTHING. No extra vacuuming needed.

Nice shop brother. Looking forward to seeing the continued growth.

Can you put a reverse control unit on it? I hav a Woodmaster 25” planer that converts to a drum sander and I bought the reverse option. Well worth it. ‘

Is that Garnica ply?

I dod not notice phantom cnc on the post processor list on the mozaik website. Was there any issues getting phantom and mozaik compatible?

Excited to be a new subscriber, Nolan. Great vids and excited to get rolling with Mozaik!

Great

I cant find the link on which stickers you use?

Just a heads up.... in regards to drawers behind doors, there are "zero protrusion" hinges that fully clear the cabinet when open so you don't have to use blocks and smaller drawer boxes. They use the same drill pattern but the knuckle is much larger so you have to be aware of where you use it in relation to the drawer box.

After watching your videos I decided to try out mozaik last night after singing up I never got my DL links or anything 😡 how long did it take for you to get you Auth Code I was app up to start learning it Great content 👍🏾

I couldn't believe this guy was cutting directly on his CNC tabletop but I see it's the full spoil board gasket from Allstar can you tell a differents with it? Very cool way to make a beveled table thanks for the info

Thanks for the USB tip, very wise.

How many kitchens would you say you have cut out on this by now? Thanks

Thanks!

Great overview Nolan! We've loved following this project and it turned out amazing! 😍👏👏👏

Love it! How's the Phantom working out for you now that you have some miles on it?

Great video Are you using pre finished plywood? I’m hoping to upgrade my 24x48 cnc to a phantom like yours in the future 😍👍🏾

Thanks for the video. Really helpful

Did you remove the hold down rollers? Or does this machine not have one?

Yep. Looks just like the one Jay Bates made 4 years back. It's a good system and it'll save lots of maintenance on your split.

Thanks for making these videos. You’re doing exactly what I want to do. Is there anything you don’t like or have had problems with, using this phantom?

Have you not got a spoil board on there

Wish I had your high ceilings! I'm doing this project right now. But my ceilings are only 9ft with a nearly flat roof, so my filter box is horizontal up to the ceiling. The box has tons of angles because the ceiling is slightly sloped in two directions. And I have two to make of different sizes/shapes--one for the woodwork side and another for the smaller metal work side of the shop. It's a real skills-building challenge!

I enjoyed watching and learning, thanks

Is this software for free?

Do you like haveing the 5 * 10 or would a 4’ * 8* have been good enough?

how long did it take you to do the whole job?

Wait so can it take 1/2" and 1/4" router bits?

Odd question …. You can not reply if it’s too private of a question but how much would did you charge for something like that me personally would range it at $3700 With material being about $1300 .

So DIY now means get 5 dudes to do it for you? Ok, good to know...

I thought you said you was gonna DIY

Dan kenfolk!😮

we are soft form edge banding machine suppliers from China, welcome to inquiry, thank you!

Great video! I would have liked to see how you do your fillers and crown. Great Job!