วีดีโอ

Where did you get the American flag decal that's on the roof of the car?

My 07 4.7 towed my 3/4ton 40 miles home bout 7500 trailer an all did fine with break control just slow

5:33 ... yes to Scamp video. 🙂

i wish i had your talent.. Im about to acquire a 1976 spitfire that i owned back in 1983.. I need to do some work on it.. I dont know what im in for lol

I have a green CT1 as well! Not as nice as yours, but love those little bikes

Brilliant video. I have a 1973 ts250. I am struggling to find a steering damper and a 6 volt sealed beam head light for it. Would you have any ideas on where to get them? I live in England

Good to see you back 🙂

Good luck stick

Why don't you turn that annoying fucking "music" off?

Hi.

He found a stick.

what did you do with the loose connectors that connected to the ac and the condenser?

Another YT video did this too. They upgraded the rear brakes to a Taurus so the rears increased in piston size to help keep the same f/r bias. Front upgrade alone moves the bias forwards.

The Chevy Colorado you could get a 5.3 v8 and it came with four doors lol

I had that exact bike purchased new in 1973. My buddy bought the green model. Together we painted my Grandmothers house and used the earnings to buy them. I’m pretty sure they were somewhere around $700 each. What a blast that bike was. Had to let it go when I got married a few years later. Still in my dreams occasionally.

I hardly use my aircon in the summer, and the heater doesn't work properly. Might pull it out. If I can be bothered.

I just LOVE seeing young men turning wrenches, LEARNING and solving problems! THIS is what ALL young people need to do. Get OFF the phones and go discover the electro-mechanical world around you.

Got my Vauxhall since 5 years with an worn a/c compressor, so while i was cleaning the intercooler i decided to remove the condenser to let my intercooler Breath a low bit ! 😷

I want to suggest a Manual impact driver with the JIS bits.

Great job!

Just took my new to me car to get re gassed to find out it’s missing a couple ac pipes 😅

for the shifter location. i don't know miata gearboxes at all. but i see it does have a shift rail. on ford T9 gearbox swaps the shifter is also where yours is with the miata gearbox. but, on the T9 trans the shift rail can be shortened and the tail shaft cut to match and then rewelded back in place. if i'm not clear here you can google up ford T9 shortened shifter mod on google to see what i mean. it's a fairly straightforward modification on the T9... which on just a glance looks like it could be done your miata trans.

Needed that screwdriver just now. Had to weld nuts on the screws cuz they were rusted tight. Got em out. Need new bolts now.

Great progess, well done.

I'd be inclined to put in larger bolts for the seat belts. The ones I've seen in most cars are bigger than that. Just measured some spares of what went in the Miata, they were 3/8" diameter.

It won't be long before you will be driving it.

Well done!

Hey buddy 😊

I have the same car in the same colour, I'll bet that's gonna be one heck of an upgrade when its done, Ive always wished mine had a bit more power and one more gear

Nice car. You have to really love them to do that much work. Some people don't understand.

Nice vid. I just blew a head gasket in my 2003 Cobra…I wasn’t sure if head removal was possible without dropping the k member (as many online forums suggest), but your video gave me hope. Not looking forward to removing drivers side head, but better than pulling to whole motor. Good job.

Torque specs? Hard to find.

Nice vintage 2 stroke Suzuki that as you mentioned with some work and parts it should become almost at 90 percent good, you have great looks to where you would do great as a model for G Q magazine with modeling sharp cool presentations over in Milan Italy perhaps getting to Paris France. ❤

I love to see that at least one member of the next generation of this family knows which end of a hammer to hold. 🙂

Yep the Prince of Darkness knows all the tricks on old British sports cars. At least the wires are thick unlike modern cars. Got similar problems except I have a grp bonnet so no easy earth ing points Great work..

I love that year and model also. However, I prefer it in green.

The lights are on...😀

The seat will lower if you push down on the seat adjuster. I have the same truck.

hey brother any luck on the f7 i have one aswell and i want to get it running

i will to that to my 87 fiero , for the same reeasons . better cooling weight savings more room and maybe put in a built in air compressor for shits and giggles

A spring connects the brake light switch to the pedal.

So awesome nice job Mason !!!! Love the old school bikes.

I'm so excited!!

Hey i love to see it! Any way you could comment or send me the links to parts for this job? I would love to do this on my Dakota!

Everything rattles around driving a spitfire my friend,these were built 5minutes from my house , Canley classic love um 🇬🇧 🇬🇧

Best bit of information was remembering to remove the clip! Great job

For one you got the worst one 😂😂😂😂

Where did you find your camper shell I've been looking for one for ever

Here's the worst. The bed is too narrow to fit a sheet of plywood flat between the wheel wells. It's about 2 inches too narrow. STUPID CALL, DODGE!!!!!

#6 it's never worked. Lol