Random alarm! - Land Rover Freelander 2 / LR2
ฝัง
- เผยแพร่เมื่อ 24 ก.ย. 2024
- Part 1 of a 2 part video looking at how to fix the alarm on a Freelander 2. My alarm kept going off randomly. The culprit was the bonnet switch. This video shows a quick and dirty workaround to stop the alarm being triggered.
In part 2 I will replace the bonnet latch and switch to resolve the issue properly. - ยานยนต์และพาหนะ
This video is amazing! Alarm going off past 10pm at night and after some frantic searching, this was the solution I needed. With a torch, pliers and a clip I got it done and the neighbours and our house can sleep.
Thank you so much for this detailed video!!!!
I can’t thank you enough for this, you saved me from embarrassment and insomnia! Thank you! 🙏🏽
If you want a really quick fix that takes two minutes just bear the wires before they go into the switch and twist them together.
.
The last two nights have been the first nights I've been able to have my car locked in silence, it's lovely😊
Go to 8:05 guys, switch plug removal.
Thanks for the vid, it is very helpful, my one started playing few months ago but it's getting more often and Ive noticed "bonnet open" light on the dashboard so I thought it's the switch causing this. Thanks!
BTW, I like your washer fluid cap, no more mess, good stuff! 👍😊
Excellent fix, wheres the part 2 that so many comments promised! I want to see how easy it is to do a replacement before i give in and ask the garage!
I need to show the switch replacement I know. I’ve got used to not having to worry about my bonnet triggering the alarm!
Thank you so much. I did this this morning. Only thing was, I had to degrease the plug to get the tape to stick. Little bit of copper electrical wire did the trick. 👍
Nice tip, thank you. Definitely a good temporary solution especially if you are on vacation and you need to lock the car. Thanks again.
ive had my LR32 for about 3 months now and its only recently i realised that it was definitely the bonnet that was the problem. so thank you for the advice and i will get out and do the deed in a few hours.......
Just used this quick fix during my lunch break. it really does only take two minutes. Especially if you have slim hands and not Homer Simpson fingers like me. Another great video and well explained. Keep it up Beavis Pits!
Thanks Les! Glad to hear it worked for you.
so i know i have already posted but i just wanted to say a big massive thank you. its taken awhile because I'd been way too busy since 6 days back (thought it had been longer to be honest). so anyway, just got round to doing as you suggested and it works a treat. locked the car with the hood up and no alarm. 3 sodding months of searching the net trying to find the solution (or sell the car) and now its done. of course, if the alarm goes off again............. Kidding, you're a star buddy
Thanks, glad it worked for you!
Just so people are aware, it's very easy to remove the sensor itself, pop the driver side Headlight out (2 10mm bolts and a push catch at the rear) Headlight out you can see the plastic sensor under the lastch, small flat head screwdriver to remove the sensor and a replacement is £15
Yep, I’ll be showing this in part 2! spoiler alert! 😂😂😂
Thank you so much!!!!! Worked great. I truly appreciate you taking the time to record this video. 😊
Thanks Ken! Glad to hear it helped!
Great video. Solved problem to bonnet signal that said bonnet open. Easy fix .I have now ordered new part. Will figure how to fit it without taking the bumpers off. It maybe a bit fiddly but I determined to solve the problem without a large gararge bill
Thanks again.Graham
Remove offside headlight to give easy access to replace the switch. I’ll do a video on this soon.
My lr2 does this all the time it's a pain in the arse. Cheers for another good vid.
Great video thank you.
For the love of God why would a securely closed bonnet need to be alarmed?..? Is someone gonna steal your engine overnight? 😂
Yup. Serious commitment dude. And taaalk soooo sloooowly. Even at x2. No hurry!
A lot of my viewers don’t speak English as their first language so Mr Shlowly. Also gives me time to think! 🤔
Thanks so much for this. I’ve sorted my alarm issue out now. Cheers !!
Thank you. I found this extremely useful and very well explained. Subscribed!
😂schön dank für die Tips 👍👍
Excellent, worked first time 👍
you're a legend, was driving me insane 👍
Hi, thank you for this! I've had this exact issue for so long. Neighbours hate me (internally) 🤣. Do we have part 2 coming soon? I'd like to ideally replace the part or clean it if not damaged. Cheers
I have the new switch. Will fit it very soon!
To replace catch and switch….
The original is a two part, catch and switch. No longer available, so buy a replacement catch/switch, £15 to £30.
Lift bonnet and remove RHS headlamp unit, 2 10mm screws + plastic latch, leave to one side
Remove bonnet slam panel screws (across the top/front). 4 10mm screws this will allow the panel to flex maybe 75 mm
Reach through the headlamp aperture and behind the slam panel and remove catch assembly 2 10mm screws. you have about 75mm of working space + panel flex
Ease the catch assembly forward into the space and remove the electrical plug, pliers, screwdriver, cursing
Remove the catch release cable from its clips behind the slam panel to give working slack
Ease the catch assembly with cable attached up through the gap behind the slam panel and then work on the catch assembly on top of the slam panel
Remove the cable from the catch assembly, lever it with a screwdriver, don’t damage the rubber grommets
“Close” the new catch assembly by pressing the catch with the bar of a screwdriver
Insert the catch cable into the new catch assembly, test that the bonnet release cable now opens the new catch
Ease the new assembly back down past the gap behind the slam panel and re-seat the catch cable in its clips
Re-attach the catch wiring plug to the new assembly, check the dashboard for “bonnet open” warning
Re-attach the new catch assembly to the bulkhead, 2 10mm screws. Re-check functionality without lowering bonnet
Re-attach the headlamp, 2 10mm screws
Wash hands
Thanks. I now no longer need to film part 2! 😂
Thanks. I now no longer need to film part 2!
Is there a ultrasonic sensor in the car
There is yes, but that only activates when you lock twice. Pressing once puts it into “dog mode” which is locked without ultrasonic cabin coverage.
Cheers mate for the advice thanks
Is there any chance you could do a short or long video about the scuttle drain why it is so high at its sides and the drain down the wheel arch, because I am confused why it is funnel shaped and stand up about 1-2 inches?? my concern is water having to get that deep to drain??? or am I wrong 🙂
There are small holes below the wiper shafts. They are often hidden by dirt. These holes drain the scuttle into the funnels below, which in turn drain into the wheel arches. I’ll try to do a quick video on this soon.
I uploaded a scuttle drain video on Sunday
Fuck yeah..! Been battling for 2 years to find that stupid sensor. Just bridged it out now. I thank you with all my heart for this video. Btw..its on the same side..South Africa.. 🙏🙏🙏🙏🙏
Nice one! Glad it worked for you!
I have code B112C-87 Interior Motion Sensor , I disconnected the sensor but the code still shows. Could it be the bonnet catch generating this code?
The bonnet sensor is just a switch so doesn’t throw a code. Disconnecting the ultrasonic motion sensor may well throw an error code, in a similar way to when a parking centre is disconnected it detect it and beeps with a flashing light on the button.
@@BeavisPits what if I short the connector to the motion sensor, would that stop it throwing a code and tripping the alarm?
@@Dark_Starr2030 I wouldn’t do that, the motion sensor is an ultrasonic transmitter, it should not be shorted out. You need to replace the sensor. Note, the ultrasonic interior motion detection is only enabled when you lock the car twice with the keyfob.
@@BeavisPits I shorted the bonnet switch this morning after watching your video, I’ll see if my random alarming stops before I replace the motion sensor. I only ever lock with one press btw.
Great vid! Thank you
Thanks for the video. Will there be a part 2? 😁
Yes, at some point. I’ve bought the new switch, just need to find the time to fit it!
Hi everyone just done this to my freelander 2, looked like the person before me tried to do this. If the alarm still goes off in the night after doing this, what else could it be, please ? I have some neighbours who aren't happy about the alarms going off 🙃 😅
First check the PO did this correctly (try to lock car with bonnet open). Then you’ll need to check the boot and door switches. It could also be an insect in the ultrasonic sensor but AFAIK that only enables if you press lock twice.
Guess what! My alarm went off this afternoon! Doors and boot shut, bonnet disabled. I just unlocked it, opened and closed each door and relocked. So far so good.
At the beginning I thought I'd accidentally opened a Mark Felton video!
Apple iMovie music, widely used by youtubers, inc Mr Felton
Hi I have my LR2 and got problem with my door lock alarm everytime I close the door I need to close it hard so the alarm won’t go off. How can I remove the alarm if one of the door is not properly close? Thank you in advance
Sounds like a faulty door latch. If you join one of the facebook groups I’m sure they will be able to advise further.
Beavis Pits, do you have part 2 - how to change it ?
Part 2 coming soon! I have bought the switch, just need to change it. You do it via the headlight opening.
Great tip, thanks!
I cant find part2 😢
Not filmed yet. I have left the bonnet switch out of the alarm circuit. I’ll fit a new switch and film it soon.
One way is to not press the panic button which I mistaken for the hazards.