So, I’ve been looking around to see about doing this job myself, and I think I’m just going to pick up an extra shift at work and have a speed shop near me take care of it lol.
Good call, if your Subaru is anywhere near as rusty underneath like the one I'm working on (02wrx) in PA, it's worth paying a pro to deal with it for sure. It's about 2x the pain vs doing clutch on a fwd car and for the love of cars don't get the roll pins in the axles stuck, they can be a nightmare
I have a 2011 Subaru Legacy that needs a clutch. Today, I had one place quote me 2,200. They told me that the slave cylinder should be replaced as well. They said it would take eight hours of labor and I think he was trying to tell me there's an additional fee to re-install and "align" the transmission. If you have to take the transmission out, putting it back in should be covered in the hourly labor. Another place quoted me 1,700, but, said if it needs a new flywheel, that would be an extra 500. I've been researching this stuff myself. The flywheel is part of the clutch kit and it's about 200 dollars.
Thank you so much. Thought I had a seized e brake cable. This was the only video I could find on how to release the hill holder or even where it was located. Thanks so much!
I got the full face street tuner series clutch and oem flywheel and it’s terrible. After 5k miles it still shakes chatters really bad. I will be replacing it soon so sad.
You might have already figured it out but the while roof rail comes off by unbolting from under the headliner, then after the while rail comes off, they unbolt from the rails. Hope that helps!
Hahahaha I noticed it after 😂 coilovers going in this week so it’ll get a proper alignment after! I’m still on a 5spd, and I liked what it offered as far as power levels and driving feel!
Any updates on the clutch, about to buy their 6 puck or their street elite full face and you’re the only person I can find running McLeod. I’ve put them in a lot of mustangs and vetted as well and they’ve always been great.
confused about the 10 minutes, looks like a 1 to 2 hour job maybe more if things are rusty as they tend to get here in the northeast. would it have been faster, easier to pull the motor ?
It’s so much easier just pulling the motor. You can pull the motor in under a hour if you know what you doing. Don’t have to pull all the axels and what not or drop the trans.
Dude, i was thinking you was pulling the whole engine and trans but you just lowered the trans without removing the engine, dude i was so happy that i dont need to remove the engine for clutch change.
What in the actual fuck guys... pull the rad fans, unbolt the trans and engine mounts, slide engine forward, don't remove the driveline or axles... Holy fuck you made this 10 times more work then needed...
Hey Cody, I recently purchased and installed a Mcleod clutch on my 04XT. I've noticed mine seems a bit jerky in first and reverse, and was just wondering what your experience was like.
This is a very well done video!!! Nice job! Is your midpipe BRASS????? or is that plated or just discoloration? That threw me off. Great video though I gotta get into this one of these days. My clutch def needs replacing
Well rolling the jack over, cranking it up, opening up the tools, getting under the car, actually swapping the clutch, lowering the jack and putting it back, test driving the new clutch, cleaning the tools and putting them away, changing out of the work clothes......etc is included in your 10 minutes? Test drives generally take 10 minutes alone. This took an hour or more on a pipe dream
Dude if you gave updates on these products THAT WOULD BE GREAT! Also, this just looks to easy… you’re kind of like the guy from KIES Motorsport for my F30 just less detail 🥺🥺🥺
good job showing 9 seconds of each step. That doesn't mean the clutch swap took 10 minutes. Maybe the BRIEF explanation of the procedure took 10 minutes.. 🙄
I wish I had a Jesse come with my engine! They seem very helpful!
The Jesse brings everything together...quite literally
So, I’ve been looking around to see about doing this job myself, and I think I’m just going to pick up an extra shift at work and have a speed shop near me take care of it lol.
Good call, if your Subaru is anywhere near as rusty underneath like the one I'm working on (02wrx) in PA, it's worth paying a pro to deal with it for sure. It's about 2x the pain vs doing clutch on a fwd car and for the love of cars don't get the roll pins in the axles stuck, they can be a nightmare
I have a 2011 Subaru Legacy that needs a clutch. Today, I had one place quote me 2,200. They told me that the slave cylinder should be replaced as well. They said it would take eight hours of labor and I think he was trying to tell me there's an additional fee to re-install and "align" the transmission. If you have to take the transmission out, putting it back in should be covered in the hourly labor. Another place quoted me 1,700, but, said if it needs a new flywheel, that would be an extra 500. I've been researching this stuff myself. The flywheel is part of the clutch kit and it's about 200 dollars.
I need to replace my clutch this video was very informative and helpful thank you
Thank you so much. Thought I had a seized e brake cable. This was the only video I could find on how to release the hill holder or even where it was located. Thanks so much!
wish to ask, recently i change my clutch disk found my exedy twin plate the FRICTION TOP PLATE slightly bent/curve look like.. is this normal?
I got the full face street tuner series clutch and oem flywheel and it’s terrible. After 5k miles it still shakes chatters really bad. I will be replacing it soon so sad.
Hi, I would love to know how to get the ends of the roof rails off my Forester sg5 to paint them? Any tips would be great!
You might have already figured it out but the while roof rail comes off by unbolting from under the headliner, then after the while rail comes off, they unbolt from the rails. Hope that helps!
Did you reuse your flywheel bolts or get new ones?
Mcleod... best clutch ever!!!
Are you still running the 5 speed? why did you go the 6 puck? Also you marked the nut not the camber bolt brooo
Hahahaha I noticed it after 😂 coilovers going in this week so it’ll get a proper alignment after! I’m still on a 5spd, and I liked what it offered as far as power levels and driving feel!
So how long does it actually take you yourself start to finish for a clutch job on that car?
Any updates on the clutch, about to buy their 6 puck or their street elite full face and you’re the only person I can find running McLeod. I’ve put them in a lot of mustangs and vetted as well and they’ve always been great.
Weere u at?
Hello was just wondering if this 04 xt 5sp takes the 230mm or 240mm plate?
confused about the 10 minutes, looks like a 1 to 2 hour job maybe more if things are rusty as they tend to get here in the northeast. would it have been faster, easier to pull the motor ?
First person ive ever seen pull the transmission on a Subaru to change a clutch. Engine is easier to pull but otherwise good job 👍
I feel like pulling the motor would be easier?! I hate draining the coolant but I definitely would rather pull the motor!! Haha
Love the vids though
My clutch is worn out and im anticipating on doing it myself on a weekend
It’s so much easier just pulling the motor. You can pull the motor in under a hour if you know what you doing. Don’t have to pull all the axels and what not or drop the trans.
What hp is this clutch rated for?
Hey love the video bro how long did it actually take to get that clutch replaced
10 hours
Wow is that really a video? Nice! 😁
Yes!!
What’s up with those brakes at the end! 👀
Video coming soon ;)
Dude, i was thinking you was pulling the whole engine and trans but you just lowered the trans without removing the engine, dude i was so happy that i dont need to remove the engine for clutch change.
probably easier
I had a price quote for 3.5k to replace my clutch on my 2012 wrx Going to do it myself
Update? I was just quoted $4200 for my 2011 WRX.
I'm doing everything you are right now. And I'm reusing bolts lol
What in the actual fuck guys... pull the rad fans, unbolt the trans and engine mounts, slide engine forward, don't remove the driveline or axles... Holy fuck you made this 10 times more work then needed...
Hey Cody, I recently purchased and installed a Mcleod clutch on my 04XT. I've noticed mine seems a bit jerky in first and reverse, and was just wondering what your experience was like.
Mine does the same. I’m gonna replace it with an exedy i think. Almost embarrassing to drive
Where do you get youre torque specs from?
This is a very well done video!!! Nice job!
Is your midpipe BRASS????? or is that plated or just discoloration? That threw me off.
Great video though I gotta get into this one of these days. My clutch def needs replacing
Well rolling the jack over, cranking it up, opening up the tools, getting under the car, actually swapping the clutch, lowering the jack and putting it back, test driving the new clutch, cleaning the tools and putting them away, changing out of the work clothes......etc is included in your 10 minutes? Test drives generally take 10 minutes alone. This took an hour or more on a pipe dream
why wouldnt you just pull the motor to replace your clutch? dropping the trans seems like making more work for yourself
Dude if you gave updates on these products THAT WOULD BE GREAT! Also, this just looks to easy… you’re kind of like the guy from KIES Motorsport for my F30 just less detail 🥺🥺🥺
Hey mate, silly question but what hood struts are you using on your forester?
good luck buying one for a subaru outback its almost a $1000 to expensive
Nt03s lurking
made it look easy.. my foz been sitting in the garage for a year blown clutch. dam.... i might just do it my self :|
You ever do it?
stil sitting there., starts first try tho even i havnt looked at it in a year. i just need the money and equipment., it will be done! someday
@@kaiziel damn some day! You have an IG?
My impreza wagon is the same, will get there one day but not today 🥺
Why the hell aren't you pulling the motor instead of all that shit i don't understand
can i be the first one? Aussie fan
Hell yes you can!
funny humor
This will definitely take more than 10 min🤌🤌🤌
good job showing 9 seconds of each step. That doesn't mean the clutch swap took 10 minutes. Maybe the BRIEF explanation of the procedure took 10 minutes.. 🙄
Welcome to 2010, and clickbait titles
More like a whole day of work..
😂😂 fuck I thought you mean I could do it faster got me 😂😂 8hrs over 2 days 😂😂
@darrengeorge2308 I got them down to like 6 hours. They can be a pain putting that heavy transaxle back in.