Dirt Bike Shock Rebuild - DISASSEMBLY

แชร์
ฝัง
  • เผยแพร่เมื่อ 20 พ.ย. 2024

ความคิดเห็น • 17

  • @hyperrhino9258
    @hyperrhino9258 ปีที่แล้ว +3

    Thank you for showing this shock rebuild. This is very similar to a 150r setup, so much appreciated.

    • @brian.d.mobley
      @brian.d.mobley  ปีที่แล้ว +1

      Sure! That’s a really old video so I’m glad there are people out there that can benefit from it. Thanks for watching!

  • @CampbeIIs
    @CampbeIIs 8 หลายเดือนก่อน +4

    Finally I found a video where they don't have $150 in special tools to rebuild the damn shock.

    • @brian.d.mobley
      @brian.d.mobley  8 หลายเดือนก่อน

      Ha! I try to use “normal” tools as much as possible! Thanks for watching!

  • @aarr3193
    @aarr3193 3 หลายเดือนก่อน +1

    Excellent video.

    • @brian.d.mobley
      @brian.d.mobley  3 หลายเดือนก่อน

      Glad you liked it! It’s an early one and I was pretty inexperienced with videography back then.

  • @ReganCampbell-tp2lx
    @ReganCampbell-tp2lx 7 หลายเดือนก่อน +1

    Can you replace the bumpstop without pulling the shock completely apart

    • @brian.d.mobley
      @brian.d.mobley  7 หลายเดือนก่อน

      Unfortunately, no. 😢

  • @davidpalmer287
    @davidpalmer287 3 ปีที่แล้ว +3

    If you have and handheld air pump you can put it on the schrader valve and give it a pump the bladder will pop right out, its a little bit messier that way but ive had bad luck with snapping valve stems.

    • @brian.d.mobley
      @brian.d.mobley  3 ปีที่แล้ว +1

      Hey David. I never have had trouble getting the bladder off, but thanks for the tip! And, thanks for watching!

    • @davidpalmer287
      @davidpalmer287 3 ปีที่แล้ว

      @@brian.d.mobley Really? Almost every shock i have done they have all been a major pain to get out but they also have been way beyound their service life. But I appreciate all the videos you make, they are very imformative.

    • @brian.d.mobley
      @brian.d.mobley  3 ปีที่แล้ว

      @@davidpalmer287 Maybe I have been lucky! What I DO have problems with is getting that dang seal on that goes around the piston. I do a lot of cussing when I work on those! HAHA!! Thanks for watching my videos! Im so glad they help! Its very satisfying to know you can help others with stuff like this.

    • @davidpalmer287
      @davidpalmer287 3 ปีที่แล้ว

      @@brian.d.mobley Yea. Those suck. Ive been using the low friction ones that mx tech offers they are cut with a little alignment notch in the center so the ends mate back up.

    • @brian.d.mobley
      @brian.d.mobley  3 ปีที่แล้ว +1

      @@davidpalmer287 I have been using the same! So much easier. But they dont make one for every shock.

  • @omarmonoruiz
    @omarmonoruiz 7 หลายเดือนก่อน +1

    badass $$$

    • @brian.d.mobley
      @brian.d.mobley  7 หลายเดือนก่อน +1

      Glad you enjoyed it