I like the workmanship and simplicity. I added my own modification. Instead of screwing the floor to the boat ribs, I put two stainless steel hinges on one end (to the bench) so the floor lifts up so that if water gets into the boat, you can lift the floor and let it dry between trips to the lake. Now the floor and the side storage boxes all lift up.
Great descriptions and detail. I think I'll try the EVA foam instead of carpet, but your description is so clear that it will be very easy to do this. Thanks!
I modified my Tracker 1436 similarly but used insulation on the sidewalls covered with Luan panels and carpet. Front and rear trolling motors and dual fish finders, pedestal seat mounts, and remote anchors completed the upgrades. Electrical runs enclosed in split tubing assured reliability. I heated the boat with Coleman lanters on the floor fore and aft. Even in the dead cold of winter, the insulation worked so well that I would fish in shirt sleeves as anything else had me sweating. Night lites rounded out the project. I kept it for 7 years, selling it only after buying a brand new Tracker 175 Pro TX. LOVE your channel! Keep the goodies flowing.
I love your work and attention to detail is on point! Quick tip on your rib notching...use a hole saw the size of your rib width and then cut from the outside of your ply with your jig saw for super clean cuts. Great video either way!!!
Bravo sir , at time about 8:00 the use of the leaf blower , excellent ! Good modern idea . Another neat modern leaf blower idea that I saw recently was leaf blowers being used to clean sand/grit off of a large go kart track on race day . Good video .
Man, I just did this to my Jon boat last week and wish I worked off had this video to shorten the learning curve.. I ended up about where you did on your video but I took a little bit longer to get there since I had never done it before. Great video. I like how you make this project accessible for the average Joe. Keep up the great work.
I took the crnter seat out insulated the bottom with the blue foam board covered it sll with plywood. Use both for hunting and fishing. Use a mr heater with a 20 pound tank for waterfowl season. My blind keeps in the heat. Good job on the build.
Very informative videos. I’ve been restoring and building boats for years now, can I make a friendly suggestion? When you put resin on plywood it works much better if you mix 50/50 resin and acetone. This lets the resin saturate into the wood instead of float on the surface. Definitely do the underside as well. PS- double up on hardner (MEK) when you mix 50/50 resin and acetone. Good luck sir.
One Of The Best Budget Friendly Videos On Boat Floor Builds ! I Was A Little Nervous On Self Taping Screws But They Looked Great After They We’re Applied.And Yes I To Cross The Street for Good Deals At Lowes And Home Depot ! Going To Use Your Method Because I Don’t Want To Remove My Bench Seats And Saving Money On A Fixed Income Is A Must ! New Subscriber Thanks Very Much
Blains Farm and Fleet has gallon Bondo Resin for $49.00 a gallon and $7.00 shipping flat rate . My 1 gallon just arrived and was slightly dented but made the journey./ Hardner was included..................Keep on Jon Boating in the Free World !!!
My first one was like that with Marine Grade Plywood, second one was a sheet of aluminum .125 which was lighter does not rot. I used the blue insulation as well.
I used 2" foam to match my rib height and just put a rubber mat trimmed nicely on top. It pulls out easily at the end of the seasons to wash down and reset it.
I ran my 1448 Jon boat with a piece of 1/2" plywood floor. I treated the plywood with deck oil. No foam. No resin. No carpet. No staples. Bare plywood can dry out between trips. Lasted for years and years, even donated the floor to a friend w same model boat. Don't try and measure out the size of the floor. Much easier and accurate to make a pattern from cardboard.
great video man. Ive got a bunch of plans for the jon boat I picked up last year, once its not winter here anymore Im gonna get going on it. This is how im gonna do the floor, thanks.
I did the same type of setup for my river jet sled. I put aluminum riv-nuts in the floor board so i can easily take it out with star knobs. Sand build up bad in there with lots of kids, and any bilge water early and late in mn freezes up which creates a ton of extra weight. Removable flooring lets me blow it out with my hotsy pressure washer.
You actually did this nicely, you utilized the benches and kept the same space seen countless vids of people adding decks which is cool but also swapping there space for convenience great job
I like the way you speed through the long processing and you did a good job on explaining I’ve done a lot of boats in my ears but it’s always good to watch out other people and other ideas thank you
I put 1 1/2 styrofoam on bottom of hull then riveted 1/16 aluminum checker plate on top of styrofoam and into Ribbs only added 22lb weight of boat it won’t absorb water and is not slippery when wet. Simple, good looking and will last forever and not any more expensive than plywood
Is there any reason you don’t use hydro turf, or is it because of budget, I think you have nailed it through the years, for content and know how. You have motivated many of us. Thank you for that, I got a hook in the carpet and ripped it but I didn’t trowl the glue I just sprayed out of an aerosol can . That might be the reason behind the rip….?
Is there any reason you don’t use hydro turf, or is it because of budget, I think you have nailed it through the years, for content and know how. You have motivated many of us. Thank you for that, I got a hook in the carpet and ripped it but I didn’t trowl the glue I just sprayed out of an aerosol can . That might be the reason behind the rip….? bTW your voice really works for video!
At the time of this video Hydroturf was not popular yet. As of now, I only use it on aluminum. I suppose you can thickly coat plywood in resin and then cover it in turf. I haven't done so yet, but that's how I'd try. I wouldn't stick it to bare wood, but that's just me.
Just what I was looking for. Great video! I have a 1984 16/52 Monark which I found corrosion in the bottom do to previous owner care. I’m learning as I go on this project as this is my first aluminum boat. Had I known what I know now I would’ve found another boat to work on. The floor I removed had treated plywood on the bottom topped with sheet metal pieces (old signs) and hide by a nice looking none slip flooring material , looked great when I purchased it thinking I’ll have fun fixing up the motor since I am a mechanic which I did. Then I started on the boat and found things I had to pay someone to weld etc.. I have spent hours removing corrosion. I want to keep an eye on it so I was looking for an easy way to build a removable floor. Also the middle bench has been removed and I watched you use hat channel in another video but I can’t locate the small amount I need? I have a thousand questions on this project so I’m going to watch the rest of your videos. I’d bring you the boat but I’m in Texas. So keep up the good work and thanks again.
Hey Cousin! Having recently inherited a 16ft jon boat, I've been studying your amazing mod techniques! How did you handle the carpet folds on the rib notches? Folding, cutting, both? I've seen your videos on carpeting inside and outside corners, but this is different. Love your work!
One cut down the middle, then from center make a bunch of diagonal cuts. Envision the rib cutout now overlap that with how youd cut a pizza. Basically you end up with a whole bunch of triangles you can manipulate around and staple to the back. Hard to explain, hope that helps
What does something like this cost? Does the plywood add a lot of weight ? Would it be better to do the floor out of aluminum for weigh reduction? Or is the plywood not much of a difference
i did this about 20 yrs. ago. the ledgers are not needed. i notched around the side ribs for a snug fit, but leave room for carpet wrap. if left outside it lasted about 4 yrs. before it needed replaced.
Bondo brand fiberglass resin is polyester resin. If you want your floors to last more than a few years you should consider using epoxy resin. Polyester resins delaminate and crack quicker than epoxy. It’ll work but it won’t last as long.
liked and subscribed, so many people make this overly complex without explanation. Thanks for the details, and i wondered how to utilize the seat space on these narrow jonboats, will be watching your seat cutout vid to get my workhorse up to snuff
That’s funny, I refurbished a boat one time in my life and I did exactly what you wanted against with the carpet. I don’t think I put too much glue on it because I used the little tool with the grooves but I think I over rolled it and ended up having some of the glue start to come up through the carpet, luckily I stopped once I noticed it and everything worked out good but they were a couple areas that were a bit stiff. If I didn’t use the tool with the notches I’m pretty sure I would’ve put way too much glue on there and destroyed it.
Check you local laws on faux floors in boats also . In Texas if you add a faux floor to a boat you are required to carry a fire extinguisher . Vs if you just have open floor like a lot of Jon boats are sold as from the dealer then fire extinguisher isn’t required .
No. I debate that a lot. Not any better option and aluminum corrosion in applications is WAY overblown to the level of people being misinformed. Not saying the boat manufacturers get everything right but even Tracker uses stainless for factory installs.
When I read super simple I was expecting a laid down piece of carpeted plywood. Don’t thinking I’d want it that attached for ease of checking my subfloor, but looks nice.
be interesting to disassemble that now and see if you've had a lot of galvanic corrosion putting stainless steel screws straight into the the aluminium rails
Hey love your videos. Im doing this my boat currently. Anyway, you happen to know where else i could get that 1" x 1" metal piece? The link isn't working.
Hi , looks great!!!’ I never have jon boat but I look forward to buy one My question is , went you pull out all the foam from the seat for the storage room, doesn’t affects flotation of the boat. ? Thanks for sharing your video.
No. The boat floats without any foam. The foam is there in case you flip the boat over in the water or in case it takes on A LOT of water to help you stay afloat a bit longer before sinking.
Great video and thanks for showing each step along the way. Do you think the plywood could be substituted with pegboard instead? Since the foam is underneath and providing rigidity and with the resin covering it should hold. Any thoughts or things to consider?
Thanks for the video! What kind of plywood do you recommend? I’m unable to find any marine grade wood unfortunately. I still plan to coat the wood with fiberglass resin and hardener like you did in the video. Thanks in advance
I don't use marine grade.I use 1/2 inch "exterior" grade. The exterior grade is rated for exterior home sheathing and the plys are glued with water resistant glue to prevent delamination if it gets moisture in it. Still coat in resin.
Thanks man, yours has been one of the simplest but good quality floor plans I’ve seen and I am going to use it. In your opinion does building a deck on the front of a jon boat give it more support and make it float more, would like your input on that because I’d like to do that and this flooring on my boat.
I believe in this one it's just floating. The plywood sandwiches it in tight. You can glue if you want to hold it in place but one the wood is down it doesn't go anywhere.
You provide an excellent demonstration and it looks easy but I'm as mechanically inclined as a bowling ball and I'm afraid I'd mess it up. Wish I knew someone who did this kind of thing.
@@AnthonyJonesBrigadeBoats Ok thanks and thanks for the video. I had another question. Do you really need the angled aluminum if you screw down the wood floor?
It might be ok without it so long as there is foam under it. I prefer to get the corners/ sides tied down securely because thats the spot where it's going to warp or bend. Definitely better with it but not 100% necessary if you want to try without end supports.
I used to do both sides. It doesn't hurt. In reality the bottom will only soak water if the boat is really flooded. So, for time, cost, material savings, i now just coat the tops and sides. Hope this helps.
I'm doing the exact same build on an almost identical boat. After curing the wood with the resin is it absolutely necessary to sand it before applying the glue for the carpet ? Also on the "benches" I'm carpeting those as well I've sanded them down to the bate aluminum,do I just apply the same carpet glue directly the the aluminum then lay my carpet? Or do I have to treat or prep the aluminum surface with anything first ? Thank you for any help
I sand the resin because sometimes there are clumps, bumps, or surface imperfections that could affect the carpet job. Also, the resin comes out slick and waxy, not a great surface for glue to bind to. I highly recommend spending an extra 10 mins to hit it with some 60 grit to at least scuff it up some, nothing crazy if you don't want, anything is better than nothing. On the bare aluminum, yes, just apply the glue then carpet. I use carpet glue or contact cement. Not to confuse you, a full new how to carpet video coming soon showing what glues i use on what parts and materials and how i carpet a full boat using different techniques. Thanks
What about drainage through sides. It looks like you have a tight fit. There are times i get sloppy with netting fish. The other day i tipped my cooler taking out of boat and fish fell on floor. I'm thinking of cleaning mess. Thanks
Good job and video. I'm just not a fan of carpets for boats . It holds moisture . Hooks gets caught in the fibers . There's other choices . But to each there own . Thx .
Yes. Hydroturf or Seadek is an option. Need to use aluminum for that. Those are 150 a roll for the real deal, plus aluminum sheet. That 25$ floor just went up to 350$. This was a simple budget deal but get as high end as you prefer.
@@AnthonyJonesBrigadeBoats there's also good ol linoleum that's cheap and easy . Still used on kitchen florring Available everywhere. Lots of colors and patterns and is environmentally friendly . Lots of guys and companys like carpet . Happy New Year . Stay Healthy and Happy . Thx .
Have you found any product that can be used to seal the inside of a jon boat? I mean every jon boat will leak a bit, and a bilge pump can be used, but if a floor is added to a deck to convert to a bass boat i would imagine that water is going to come in under the added materials.
No jon boat I ever build leaks at all. Not a drop. I water testtgembefore a biuld and if a leak is found, I fix it. This can require welding, patching, replacing a rivet, or rebucking a rivet it. I do not seal the inside of a boat. That's like putting shingles on the inside of your house. You seal tge outside of the boat. This is called "bottom coat". I recommend different products depending on your project but personally I am using Fasco Super Slick. It is a 2 part epoxy which goes on thick. Once cured it will seal around all rivets and create a flexible durable thick coat on tge bottom of your boat. Of course it's about 125$ for the quart kit and depending on your boat you may need 2 kits. Also need to flop the boat and sand or wire wheel the whole bottom to aluminum. This takes time. This is the proper way to address what you mentioned.
I like the workmanship and simplicity. I added my own modification. Instead of screwing the floor to the boat ribs, I put two stainless steel hinges on one end (to the bench) so the floor lifts up so that if water gets into the boat, you can lift the floor and let it dry between trips to the lake. Now the floor and the side storage boxes all lift up.
Nice! Great idea cuz
Show us a video
Oh yeah that is smart, thank you
Great video! I’m mowing lawns on weekends to save up for my first jon boat, I wanna get one before April 2022
Keep grinding man👊 Good things come to those who work for it!
@@AnthonyJonesBrigadeBoats thanks man! It’s for sure a grind but it’ll pat off
That's awesome, you should be proud of yourself.
How old are you bro?
Good job. Keep up the hard work. (Fist bump)
Great descriptions and detail. I think I'll try the EVA foam instead of carpet, but your description is so clear that it will be very easy to do this. Thanks!
I modified my Tracker 1436 similarly but used insulation on the sidewalls covered with Luan panels and carpet. Front and rear trolling motors and dual fish finders, pedestal seat mounts, and remote anchors completed the upgrades. Electrical runs enclosed in split tubing assured reliability. I heated the boat with Coleman lanters on the floor fore and aft. Even in the dead cold of winter, the insulation worked so well that I would fish in shirt sleeves as anything else had me sweating. Night lites rounded out the project. I kept it for 7 years, selling it only after buying a brand new Tracker 175 Pro TX.
LOVE your channel! Keep the goodies flowing.
Great budget job. I would have sealed both sides of plywood because most leaks occur below deck.
I love your work and attention to detail is on point! Quick tip on your rib notching...use a hole saw the size of your rib width and then cut from the outside of your ply with your jig saw for super clean cuts. Great video either way!!!
Thanks for a well detailed and informative video. Just finished putting a deck in my Jon boat. Turned out great!
I added this exact same floor to my 1542 and it's been great so far. Thanks for this!
Bravo sir , at time about 8:00 the use of the leaf blower , excellent ! Good modern idea . Another neat modern leaf blower idea that I saw recently was leaf blowers being used to clean sand/grit off of a large go kart track on race day . Good video .
Man, I just did this to my Jon boat last week and wish I worked off had this video to shorten the learning curve.. I ended up about where you did on your video but I took a little bit longer to get there since I had never done it before. Great video. I like how you make this project accessible for the average Joe. Keep up the great work.
I took the crnter seat out insulated the bottom with the blue foam board covered it sll with plywood. Use both for hunting and fishing.
Use a mr heater with a 20 pound tank for waterfowl season. My blind keeps in the heat.
Good job on the build.
CPES is a GREAT sealer too... It's used in wood ship & boat building. Clear Penetrating Epoxy Sealer. Thanks for sharing
Very informative videos. I’ve been restoring and building boats for years now, can I make a friendly suggestion? When you put resin on plywood it works much better if you mix 50/50 resin and acetone. This lets the resin saturate into the wood instead of float on the surface. Definitely do the underside as well.
PS- double up on hardner (MEK) when you mix 50/50 resin and acetone. Good luck sir.
Thank you. I will try this. I appreciate your advice!
@@AnthonyJonesBrigadeBoats Have you tried the 50/50 on anything yet. Would like to know your opinion.
One Of The Best Budget Friendly Videos On Boat Floor Builds ! I Was A Little Nervous On Self Taping Screws But They Looked Great After They We’re Applied.And Yes I To Cross The Street for Good Deals At Lowes And Home Depot ! Going To Use Your Method Because I Don’t Want To Remove My Bench Seats And Saving Money On A Fixed Income Is A Must ! New Subscriber Thanks Very Much
Great instructions and clear methods, this is a huge help as we are starting our build
Blains Farm and Fleet has gallon Bondo Resin for $49.00 a gallon and $7.00 shipping flat rate . My 1 gallon just arrived and was slightly dented but made the journey./ Hardner was included..................Keep on Jon Boating in the Free World !!!
Lol @ballin on a budget! Thats my favorite phrase. Nice work and video.
My first one was like that with Marine Grade Plywood, second one was a sheet of aluminum .125 which was lighter does not rot. I used the blue insulation as well.
I used 2" foam to match my rib height and just put a rubber mat trimmed nicely on top. It pulls out easily at the end of the seasons to wash down and reset it.
Great job explaining the step by step process with your builds. Thank you for sharing your process with everyone.
I ran my 1448 Jon boat with a piece of 1/2" plywood floor. I treated the plywood with deck oil. No foam. No resin. No carpet. No staples. Bare plywood can dry out between trips. Lasted for years and years, even donated the floor to a friend w same model boat. Don't try and measure out the size of the floor. Much easier and accurate to make a pattern from cardboard.
With the foam did you really need the ledgers? Thanks cool easy project.
great video man. Ive got a bunch of plans for the jon boat I picked up last year, once its not winter here anymore Im gonna get going on it. This is how im gonna do the floor, thanks.
very precise! Appreciate the step by step process. Easy to follow along to when trying to replicate.
Another great one cousin! Man I just noticed 21K subscribers now! Fantastic!
I did the same type of setup for my river jet sled. I put aluminum riv-nuts in the floor board so i can easily take it out with star knobs. Sand build up bad in there with lots of kids, and any bilge water early and late in mn freezes up which creates a ton of extra weight. Removable flooring lets me blow it out with my hotsy pressure washer.
You actually did this nicely, you utilized the benches and kept the same space seen countless vids of people adding decks which is cool but also swapping there space for convenience great job
Subbed. Thanks for the help you’re a genius
Appreciate it 🙌
Glad I found your channel! I have an old Alumacraft 14’ Jon boat I’ve wanted to restore!! I’ll be checking our all of your DIY’s!! 😎
Looks really nice. I would just use grey deck stain and not bother with carpet that will hold moisture and rot the plywood.
I like the way you speed through the long processing and you did a good job on explaining I’ve done a lot of boats in my ears but it’s always good to watch out other people and other ideas thank you
No problem, thanks for positive feedback my friend
I put 1 1/2 styrofoam on bottom of hull then riveted 1/16 aluminum checker plate on top of styrofoam and into Ribbs only added 22lb weight of boat it won’t absorb water and is not slippery when wet. Simple, good looking and will last forever and not any more expensive than plywood
Just finished mine if you bevel the outer edges about fifteen degrees in it'll drop in tight and smooth to the hull.
Making me want a jon boat more than a bass boat with this idea and the fishing deck. Even older boats are expensive as hell lol. Nice work brotha.
Is there any reason you don’t use hydro turf, or is it because of budget, I think you have nailed it through the years, for content and know how. You have motivated many of us. Thank you for that, I got a hook in the carpet and ripped it but I didn’t trowl the glue I just sprayed out of an aerosol can . That might be the reason behind the rip….?
Turned out nice - good work and easy to follow instructions! Thanks for sharing
Awesome video this is going to help me a lot just got myself a flat bottom boat and wanting to do this
Glad I could help
Is there any reason you don’t use hydro turf, or is it because of budget, I think you have nailed it through the years, for content and know how. You have motivated many of us. Thank you for that, I got a hook in the carpet and ripped it but I didn’t trowl the glue I just sprayed out of an aerosol can . That might be the reason behind the rip….? bTW your voice really works for video!
At the time of this video Hydroturf was not popular yet. As of now, I only use it on aluminum. I suppose you can thickly coat plywood in resin and then cover it in turf. I haven't done so yet, but that's how I'd try. I wouldn't stick it to bare wood, but that's just me.
Anthony, grab some fiber blades. It’s a life changer on a chop saw.
I'll look into that, thanks
Just what I was looking for. Great video! I have a 1984 16/52 Monark which I found corrosion in the bottom do to previous owner care. I’m learning as I go on this project as this is my first aluminum boat. Had I known what I know now I would’ve found another boat to work on. The floor I removed had treated plywood on the bottom topped with sheet metal pieces (old signs) and hide by a nice looking none slip flooring material , looked great when I purchased it thinking I’ll have fun fixing up the motor since I am a mechanic which I did. Then I started on the boat and found things I had to pay someone to weld etc.. I have spent hours removing corrosion. I want to keep an eye on it so I was looking for an easy way to build a removable floor. Also the middle bench has been removed and I watched you use hat channel in another video but I can’t locate the small amount I need? I have a thousand questions on this project so I’m going to watch the rest of your videos. I’d bring you the boat but I’m in Texas. So keep up the good work and thanks again.
I did something like this a month ago with plans from Woodglut.
Nice!
Just what I was looking for. Thanks!
When I cut aluminum on my miter saw, I turn the blade backwards so it doesn’t buck or grab.
Hey Cousin! Having recently inherited a 16ft jon boat, I've been studying your amazing mod techniques! How did you handle the carpet folds on the rib notches? Folding, cutting, both? I've seen your videos on carpeting inside and outside corners, but this is different. Love your work!
One cut down the middle, then from center make a bunch of diagonal cuts. Envision the rib cutout now overlap that with how youd cut a pizza. Basically you end up with a whole bunch of triangles you can manipulate around and staple to the back. Hard to explain, hope that helps
@@AnthonyJonesBrigadeBoats Makes sense! You rock and thanks!
What does something like this cost? Does the plywood add a lot of weight ? Would it be better to do the floor out of aluminum for weigh reduction? Or is the plywood not much of a difference
i did this about 20 yrs. ago. the ledgers are not needed. i notched around the side ribs for a snug fit, but leave room for carpet wrap. if left outside it lasted about 4 yrs. before it needed replaced.
and , then i got smart and used sheet aluminum.
Bondo brand fiberglass resin is polyester resin. If you want your floors to last more than a few years you should consider using epoxy resin. Polyester resins delaminate and crack quicker than epoxy.
It’ll work but it won’t last as long.
Use whatever resin you want. You know what Basstracker uses from the factory on their wood decking? Nothing. Anything is better than nothing.
liked and subscribed, so many people make this overly complex without explanation. Thanks for the details, and i wondered how to utilize the seat space on these narrow jonboats, will be watching your seat cutout vid to get my workhorse up to snuff
Try using a paneling blade installed backwards in your chop saw, no kickback and a clean cut.
That’s funny, I refurbished a boat one time in my life and I did exactly what you wanted against with the carpet. I don’t think I put too much glue on it because I used the little tool with the grooves but I think I over rolled it and ended up having some of the glue start to come up through the carpet, luckily I stopped once I noticed it and everything worked out good but they were a couple areas that were a bit stiff. If I didn’t use the tool with the notches I’m pretty sure I would’ve put way too much glue on there and destroyed it.
Great vid , what would you recommend instead of carpet for very wet climates?
You gave me ideas for my boat brother. Great video!
Check you local laws on faux floors in boats also . In Texas if you add a faux floor to a boat you are required to carry a fire extinguisher . Vs if you just have open floor like a lot of Jon boats are sold as from the dealer then fire extinguisher isn’t required .
Any issues with the stainless screws in the aluminum?
No. I debate that a lot. Not any better option and aluminum corrosion in applications is WAY overblown to the level of people being misinformed. Not saying the boat manufacturers get everything right but even Tracker uses stainless for factory installs.
Put the miter saw in backwards, works for cutting metal
Is rubber mat usable instead of carpet?
When I read super simple I was expecting a laid down piece of carpeted plywood. Don’t thinking I’d want it that attached for ease of checking my subfloor, but looks nice.
Fantastic video!
To complete the boat fully, what would it cost? ....roughly.
Drilling into the ribs doesn’t weaken it?
be interesting to disassemble that now and see if you've had a lot of galvanic corrosion putting stainless steel screws straight into the the aluminium rails
Only thing I would’ve done different on yourself tapping screws is I like those beauty washers
Nice. Definitely more than one way to do it.
Hey love your videos. Im doing this my boat currently. Anyway, you happen to know where else i could get that 1" x 1" metal piece? The link isn't working.
Hi , looks great!!!’
I never have jon boat but I look forward to buy one
My question is , went you pull out all the foam from the seat for the storage room, doesn’t affects flotation of the boat. ?
Thanks for sharing your video.
No. The boat floats without any foam. The foam is there in case you flip the boat over in the water or in case it takes on A LOT of water to help you stay afloat a bit longer before sinking.
@@AnthonyJonesBrigadeBoats thanks for your honesty 🙏 really appreciate it
If you flip your saw blade backwards you can cut aluminum without it grabbing.
Great video and thanks for showing each step along the way. Do you think the plywood could be substituted with pegboard instead? Since the foam is underneath and providing rigidity and with the resin covering it should hold. Any thoughts or things to consider?
No!
Thanks for the video! What kind of plywood do you recommend? I’m unable to find any marine grade wood unfortunately. I still plan to coat the wood with fiberglass resin and hardener like you did in the video. Thanks in advance
I don't use marine grade.I use 1/2 inch "exterior" grade. The exterior grade is rated for exterior home sheathing and the plys are glued with water resistant glue to prevent delamination if it gets moisture in it. Still coat in resin.
Thanks man, yours has been one of the simplest but good quality floor plans I’ve seen and I am going to use it. In your opinion does building a deck on the front of a jon boat give it more support and make it float more, would like your input on that because I’d like to do that and this flooring on my boat.
How much do you charge for this and the bench storage ?
Thanks for the video… did you glue the foam to the bottom of the boat?
I believe in this one it's just floating. The plywood sandwiches it in tight. You can glue if you want to hold it in place but one the wood is down it doesn't go anywhere.
You provide an excellent demonstration and it looks easy but I'm as mechanically inclined as a bowling ball and I'm afraid I'd mess it up. Wish I knew someone who did this kind of thing.
Do you have a video showing ? how they put a rod holder bar on the back of my 14' Jon boat . so I can fish for catfish. On the back end.
Sorry, I do not.
Great job bud!
I'm just curious if you have ever run a grab bar attached to a wood floor like this and how it held up?
I haven't, I'd imagine it would need to tie into a rib or hull
@@AnthonyJonesBrigadeBoats Ok thanks and thanks for the video. I had another question. Do you really need the angled aluminum if you screw down the wood floor?
It might be ok without it so long as there is foam under it. I prefer to get the corners/ sides tied down securely because thats the spot where it's going to warp or bend. Definitely better with it but not 100% necessary if you want to try without end supports.
Do trouble hooks get caught on that carpet?
Yes absolutely, it's cheap outdoor carpet
Nice I just did my floor over used foam and aluminum
Anthony when coating the plywood in the fiberglass resin to you coat both sides or just top and sides?
I used to do both sides. It doesn't hurt. In reality the bottom will only soak water if the boat is really flooded. So, for time, cost, material savings, i now just coat the tops and sides. Hope this helps.
Did you do anything to hide the wires on this build?
How could I locate someone in Dallas Ft Worth TX area to do a similar floor project in a 14’ vee aluminum StarCraft fishing boat?
I find fiberglass resin can get brittle and crack. I like epoxy all day and twice on Sunday.
Yeah your not wrong.
Other than looks. What the purpose of. It Toby out the rib notches?
I'm doing the exact same build on an almost identical boat. After curing the wood with the resin is it absolutely necessary to sand it before applying the glue for the carpet ? Also on the "benches" I'm carpeting those as well I've sanded them down to the bate aluminum,do I just apply the same carpet glue directly the the aluminum then lay my carpet? Or do I have to treat or prep the aluminum surface with anything first ? Thank you for any help
I sand the resin because sometimes there are clumps, bumps, or surface imperfections that could affect the carpet job. Also, the resin comes out slick and waxy, not a great surface for glue to bind to. I highly recommend spending an extra 10 mins to hit it with some 60 grit to at least scuff it up some, nothing crazy if you don't want, anything is better than nothing. On the bare aluminum, yes, just apply the glue then carpet. I use carpet glue or contact cement. Not to confuse you, a full new how to carpet video coming soon showing what glues i use on what parts and materials and how i carpet a full boat using different techniques. Thanks
How many 4x8 sheets of wood will that bottle do ? . I'm comparing costs to decide if I should go with wood or pvc .
I like wood personally.. Pvc is very flexible and glue doesn't stick as well. 2 sheets to do full boat.
@@AnthonyJonesBrigadeBoats Not the sheets but how mush will the resin cover ? Do I need 1 or two ?
Great job!
Great job man but floor vinyl is much better than carpet for cleaning
Does cutting the benches affect the stability of the boat
Not as long as you leave some meat around the angled edges. That's the strongest point side to side connection
Wonder if sea dek decking would adhere to the sanded resin good.
Nice job thank you
What about drainage through sides. It looks like you have a tight fit. There are times i get sloppy with netting fish. The other day i tipped my cooler taking out of boat and fish fell on floor. I'm thinking of cleaning mess. Thanks
Water finds a way man. It wasn't cut air tight my friend...
How much did everything cost
Good job and video. I'm just not a fan of carpets for boats . It holds moisture . Hooks gets caught in the fibers . There's other choices . But to each there own . Thx .
Yes. Hydroturf or Seadek is an option. Need to use aluminum for that. Those are 150 a roll for the real deal, plus aluminum sheet. That 25$ floor just went up to 350$. This was a simple budget deal but get as high end as you prefer.
@@AnthonyJonesBrigadeBoats there's also good ol linoleum that's cheap and easy . Still used on kitchen florring
Available everywhere. Lots of colors and patterns and is environmentally friendly . Lots of guys and companys like carpet . Happy New Year . Stay Healthy and Happy . Thx .
My only question is what happens if the floor is exposed to rain or a lot of water? Would it be able to drain properly?
Thats what the channels stamped in the hull are for. Yes
What kind of ply wood is that? Treated or marine?
What size rivets did you use? What size drill bit did you use? Thanks.
Just came across your channel and got some great ideas from your video. 👍🏻
Cheap tip: Old used plastic gift cards are great for spreaders too, cut notches with scissors if needed
Thanks
Looks great
I have that same exact saw
awesome vid...thanks for the details!
No problem, thank u
Have you found any product that can be used to seal the inside of a jon boat? I mean every jon boat will leak a bit, and a bilge pump can be used, but if a floor is added to a deck to convert to a bass boat i would imagine that water is going to come in under the added materials.
No jon boat I ever build leaks at all. Not a drop. I water testtgembefore a biuld and if a leak is found, I fix it. This can require welding, patching, replacing a rivet, or rebucking a rivet it. I do not seal the inside of a boat. That's like putting shingles on the inside of your house. You seal tge outside of the boat. This is called "bottom coat". I recommend different products depending on your project but personally I am using Fasco Super Slick. It is a 2 part epoxy which goes on thick. Once cured it will seal around all rivets and create a flexible durable thick coat on tge bottom of your boat. Of course it's about 125$ for the quart kit and depending on your boat you may need 2 kits. Also need to flop the boat and sand or wire wheel the whole bottom to aluminum. This takes time. This is the proper way to address what you mentioned.
Don't some of those benches have foam inside? The floor looks great...
Great breakdown