Cuervo +3mm throttle body Setup, Tps Sensor calibration, idle stop screw and air bleed setup.

Cuervo ATV Raptor 700 specialists
951-743-6328 [e-mail]
/ cuervoatv
www.ebay.com/u... Cuervo ATV Raptor 700 specialists
951-743-6328 [e-mail]
/ cuervoatv
www.ebay.com/u...

[@toolsaregreat2]

Very cool, was getting ready to do this step next. Love the videos, makes the installs very smooth! Thanks for all you do!

[@notwerudy869]

Thanks Cuervo Racing 🤙🏽

[@chriscallas9358]

Thank you sir, as always great info !

[@raptorider83]

Great vid man, good lookin out..

[@tonyfoley9988]

Screw what people think, you call it a bike if you want. I know your not the only one to call it that. I myself call it a bike and so do plenty of other people. I'm confused on why its such a sin to be called a bike.

[@yxiscatti]

Great video very helpful! thank you Daniel. Are planning to show the performance increase with the +3 TB? on the dyno? It will be great, thank you!

[@rhuaustin9004]

Daniel I was hoping you would show how to set the tps using a ohm meter. I am putting your plus three on this week but have no access to a computer..
Thanks

[@zanettialvaro]

F..k. I changed the low/top voltage on my pc6 trying to make it 0 and 100% instead of adjusting the TPS and I didn't save the original values (shame on me, always take pics). Can I use your voltages as reference for adjusting my TPS?
Thank you sir. You're a Raptor guru. Incredible content.

[@cbr600rrturbo]

Quick question I bought a new 2020 raptor 700r all stock & some times it backfires on de acceleration, I bought one of your ais block off plates & it seemed better but with a occasional backfire with a weird sound like a burst of air coming out the exhaust, is it just to lean? I plan on modding it.thanks

[@chazwuest4557]

I can adjust either of those screws all the way and my bike does not lower in idle. Any ideas what's going on.

[@trucks4x418]

So if I add a +3 tb I would have to calibrate my tps , it’s not add on you can basically put on ?

[@myronwotton4149]

Would i need to change my valve springs to run a stage 3 hot cam in a 15 grizzly?

[@arturoalexistorresperea4063]

hello mr cuervo racing I have a raptor 700 from 2006 with pc5 and it always appears 100% on the throttle part, do I have to calibrate as you did?

[@poorwhiteboy6521]

Do I need a different map for the +3 throttle body ?

[@xxcoldxx-gg8903]

Would it be safe for me to run a megahurt on my stock raptor

[@leesbikelife2231]

I'm still getting backfire on Deceleration.

[@jeffaquilino1806]

Do you need a laptop to set these TB up

[@Brian-mc4pd]

This is not what video is about, but there are only a few of you doing anything with Yamaha Raptors. I have been looking for 1 piece of info for a very long time - that's it. Do you know what the dimensions are for the main frame tubing of Raptor 660 or 700 - the outside (diameter) appears to measure 1.125 (1 1/8), but I need somebody to verify. I can not measure the thickness (gauge) of that tube. Does anybody know what the thickness or gauge is on the main frame as well as diameter? Another way to put it is if you were going to replace some part of the main frame tube, what size DOM would you get? Can be Raptor 660 or 700. Thanks

[@DsteezyMedia]

My stock TB reads same .6xx min and max and if I barely touch the throttle it goes to 100. Do I need to calibrate like you just did?

[@MrCuervoRacing]

Yes u need to reset the paramiters. Min .67 max 3.96