How to connect a Pac Audio high to low level adapter, the LP7 2

แชร์
ฝัง
  • เผยแพร่เมื่อ 29 ก.ย. 2024
  • In this video we show you on the bench how to connect the Pac-Audio LP7-2 high to low level adapter. we hope you enjoy.
    if you would like to get one go here
    amzn.to/2eF6Iqs

ความคิดเห็น • 277

  • @kaleblangley3980
    @kaleblangley3980 4 ปีที่แล้ว +26

    Literally the best explanation of this device I found I bought one and almost gave up because I’ve searched multiple videos over this Pac LOC

  • @Kenmarshallintereststx
    @Kenmarshallintereststx ปีที่แล้ว

    I've been stressing over those RCA's until I realize you can just clip them 😂 thank you

  • @BIGTAGGART
    @BIGTAGGART 7 ปีที่แล้ว +1

    just bought one..video simplified everything

  • @melvinharris9950
    @melvinharris9950 2 ปีที่แล้ว

    How do you wire that into a 2018 Tahoe LT amp is in the rear side panel driver side really need to know ?????

  • @jvssgod
    @jvssgod 6 ปีที่แล้ว +2

    Hi Dean & Fernando!! I have a question about the LP7-2. I finished installing a JL W7 stealthbox and a JL RD 1000/1 amp on my 17 mustang. I tapped into rear deck speakers for signal and ground/power from the amplifier, remote from LP to amp. Played 40 hz test tone through HU and used my DD1+ for distortions. I got my max volume and adjusted the LP7-2 to 2 volts. Now my question is, do i play the 40z test tone again and set my gain on my amp until it shows distortion?? My DD1+ has the ability for overlap and i played 40hz overlap track and used my bass boost to give me 8 db of overlap. Is this the correct way to tune my amp? Or how do i set overlap correctly? When i start and turn my car off, my subwoofer is popping/thump, is this because of the LP voltage or my gains are too high? Please help me with my questions. Thank you!!!!!

  • @7s6l94
    @7s6l94 3 ปีที่แล้ว

    So , on this I can use factory subwoofer wires to 1 channel and and split the rca's just to sub amp. Or do I need to use both channels for signal to sub amp.

  • @Reefparty
    @Reefparty 7 ปีที่แล้ว

    If I don't have the extra RCA that you cut off to use to test the volts like you did in the video ,would I just put the positive to the terminal of the loc and negative on the vehicle ??? I used this product in my DodgeDart when I first put my system in it but just got a nice tester and would like to adjust the game the new school way lol 12in alpine type r sounds good but always would like to make it better if there's room for improvement👍🏻

    • @FiveStarCarStereoInc
      @FiveStarCarStereoInc  7 ปีที่แล้ว +1

      cory shaffer connect the positive test probe to the inside of the rca hole. Connect the negative to the rca shield or out side of the rca.

  • @mfrancis706
    @mfrancis706 7 ปีที่แล้ว

    Great video, and very informative. 2 questions...
    I have a 4 series bmw and wish to add a 1000w rms amp and sub. So could I use the LP72 to do this or would you suggest a higher spec LOC. And, would it be ok to branch off one of the existing stock underseat sub wires to connect to the LOC?

    • @FiveStarCarStereoInc
      @FiveStarCarStereoInc  7 ปีที่แล้ว

      M Henry yes and yes. This will do the trick and you can tap a wire there. Don't panic if it does not turn off right away. Your car usually takes five minutes to go to sleep. It also wakes up anytime you open a door or trunk. It is perfectly normal.

    • @mfrancis706
      @mfrancis706 7 ปีที่แล้ว

      Thank you thank you thank you, cant wait to install...

    • @FiveStarCarStereoInc
      @FiveStarCarStereoInc  7 ปีที่แล้ว

      M Henry let us know how it goes

  • @HeavyHookSet14
    @HeavyHookSet14 7 ปีที่แล้ว

    can I use this same product for a 2017 honda accord sport?

    • @FiveStarCarStereoInc
      @FiveStarCarStereoInc  7 ปีที่แล้ว

      royalty axb yes, just keep in mind your car may have active noise canceling( ANC). If so you will need to unplug the microphones. Just do a search for Honda Accord ANC

    • @HeavyHookSet14
      @HeavyHookSet14 7 ปีที่แล้ว

      Thanks alot...been trying to do as much research as I can

    • @rentjeff
      @rentjeff 5 ปีที่แล้ว

      Five Star Car Stereo hum so i have unconnect in my charger so does that mean i will have to unplug my microphones to? cause that’s what stereo shops tell me

  • @strght_flxing
    @strght_flxing 3 ปีที่แล้ว +10

    Bro, twisting the power wires with a power tool; game changer!

  • @douglasesham6773
    @douglasesham6773 2 ปีที่แล้ว +1

    If you use the power and ground from the amplifier to turn on the LP 7- 2 and the blue wire from the LP 7-2 to the amplifier remote how does the lp 7-2 turn on and off

  • @edgaralonso3659
    @edgaralonso3659 25 วันที่ผ่านมา

    I don’t have a DD1 so but I have a 40 hz/0db downloaded on my phone. Followed same steps played the track and turned it up to 75% and multimeter read .001 with the gain all the way up on the LP7 😂. Im stuck

  • @Jin180sx
    @Jin180sx 28 วันที่ผ่านมา

    Hi I know you doing as example. Does it create 8 Ohm load when you combine 2 negatives and 2 positives? Does Ohm matter going in? I mean whether factory is 8, 6, 4, or 2 ohms speaker level out?

  • @darrencedeno3538
    @darrencedeno3538 3 ปีที่แล้ว +2

    Yo!!
    I swear the best explanation by far….
    Thanks 🙏🏾

  • @tshahs5130
    @tshahs5130 6 ปีที่แล้ว +4

    Great video. I have a question, I have a Honda civic, can I cut the wires from the speakers front and rear door to go into the loc or do I need to get the wires from the head unit? Thank you.

    • @rafaelbarrientos8212
      @rafaelbarrientos8212 3 ปีที่แล้ว

      Did you ever install it? I had the same question. Did it work?

    • @grikisgrikis2779
      @grikisgrikis2779 3 ปีที่แล้ว

      From rear speakers since it gives full range frequency

  • @jgizzy
    @jgizzy หลายเดือนก่อน

    I'm guessing this install setup he showed was for a subwoofer amp, because he tied two of the speaker wires together and mentioned that the sub-bass was recorded as mono not stereo. If he were installing this for full frequency speaker install, he wouldn't have done that. That's my understanding anyways, correct me if I'm wrong.

  • @brandonjohnson7559
    @brandonjohnson7559 5 ปีที่แล้ว +2

    My Voltage only went up to 1.7 so is that fine or what?

  • @mikeleschnitman9504
    @mikeleschnitman9504 2 ปีที่แล้ว

    Would this only work with speaker line in to activate? or would RCA audio line from say, iphone audio out trigger it on?

  • @arielmoreno6601
    @arielmoreno6601 6 ปีที่แล้ว +1

    What’s the difference between the PAC LP5-4 vs LP6-4 vs LP7-4? I saw one of your install videos when you where working on the exact car I own, infinity g35 with factory Bose system, in that video you used a LP5-4.
    I am now attempting that same install but don’t know to buy the LP6-4 or LP7-4...as the LP5-4 is now discontinued by the manufacturer. Please help...don’t want to order the wrong model..also I am aware I will probably lose out on my Bose sub in the rear deck using this. I’ve already picked up an amp and sub for the trunk. Installing pioneer avh2440nex.
    Also, I’ve already installed this same radio in my 2012 Altima. Will the PAC SWI RC work for both the 2005 Infinity G35 and the 2012 Nissan Altima?
    Thanks in advance for any help!

  • @13salinaspride
    @13salinaspride ปีที่แล้ว

    So I I have the kicker loc, do I have to use the right side and left? Could I just tap the left rear door speaker? 15 chevy silverado crewcab, thank you!

  • @doogonutube
    @doogonutube 4 ปีที่แล้ว +1

    Hi, great video.. I do have a question though... If you are running power to the converter

  • @darylcuster4417
    @darylcuster4417 5 ปีที่แล้ว +2

    Hi my amp will do low or high input up to 10 volts what volt should I run my head unit out at?

  • @popskitchen6513
    @popskitchen6513 6 หลายเดือนก่อน

    Do I need to install a loc if I’m just upgrading speakers and adding a amp with no subwoofer?

  • @christophergohil7721
    @christophergohil7721 3 ปีที่แล้ว

    I hooked up the power and ground to the Lp7 and And tested the power coming out Of the remove and only getting 8volt and the radio is on i should be getting 12volt

  • @eduardoperez7797
    @eduardoperez7797 ปีที่แล้ว

    My vintage radio has 4 set of speakers cables how do I connect to the LOC unit? Thanks

  • @snip_king428
    @snip_king428 2 ปีที่แล้ว

    What happens when the signal is too low, and you barely hear it?
    2016 Nissan leaf Bose system

  • @cantu340
    @cantu340 7 ปีที่แล้ว +2

    I was wondering, for this specific product, on the speaker side do you connect it just to one pair of wires for one speaker or will it go for all the speakers?

    • @FiveStarCarStereoInc
      @FiveStarCarStereoInc  7 ปีที่แล้ว +3

      Alfredo Cantu if you are adding a sub you can tap a left and right speaker. Some people will tap one front and one rear, if you fade the radio at all. You can also just tap one speaker.

  • @gfooce85
    @gfooce85 6 ปีที่แล้ว +2

    Great video!!! Alot of help. im getting ready to order one for my truck!!!

  • @sneakatoke4389
    @sneakatoke4389 11 หลายเดือนก่อน

    Mine literally wont turn on when i put ithe ground and posrive on the battery i cant test it it wont even turn on

  • @titusturner7304
    @titusturner7304 2 ปีที่แล้ว

    Where is you getting the black and gold wire from where is it coming from behind the radio

  • @BadRonald1
    @BadRonald1 3 ปีที่แล้ว

    Im asking you. So many people have questions. Why is that ?

  • @FusionRush4LIFE
    @FusionRush4LIFE 6 ปีที่แล้ว +1

    howcome my PACLP7-2 works even when the remote, and power is not even connected?

  • @padelfull
    @padelfull 7 ปีที่แล้ว +2

    hi, thanks for the video.
    Where I connect 12v in ? directy batery or stereo ?

  • @zoomob1540
    @zoomob1540 3 หลายเดือนก่อน

    so youre telling me ive wasted all this time when i could have just wired these straight into my amp🤦🏼‍♂️🤣

    • @zoomob1540
      @zoomob1540 3 หลายเดือนก่อน

      ive been trying to find a video on how to wire it behind my head unit and all of the wires are colors that dont match the pac so if thats the case that would be so much easier

  • @jbrubaker13
    @jbrubaker13 ปีที่แล้ว

    Where are you tapping into for 12v for the remote turn on?

  • @1970chevy
    @1970chevy ปีที่แล้ว

    So where did that rca for the smd come from. I have a dd1.

  • @adaboy4z
    @adaboy4z 5 ปีที่แล้ว +1

    So if I'm already using the high level input on my amp will this LOC sound better or equal?

  • @alexisland3141
    @alexisland3141 5 ปีที่แล้ว +2

    Can you do an Install using one of these LOCs but using the rear speakers to do it and avoid dealing with taking out head unit

    • @rentjeff
      @rentjeff 5 ปีที่แล้ว

      Alex Island ahh thats something i would also like to know to cause thats what i was gonna do cause its way easier plus all my wires will be in the trunk so no wire running lol

    • @eaopanama
      @eaopanama 5 ปีที่แล้ว +1

      You sure can. Like you said, just tap into the rear speakers without having to remove the radio. Remember though, you still need to run a power cable from battery to amp

    • @rentjeff
      @rentjeff 5 ปีที่แล้ว +1

      eaopanama yea i know the good thing is i gotta dodge charger so my battery is in the trunk

    • @eaopanama
      @eaopanama 5 ปีที่แล้ว

      @@rentjeff It can't get easier than that then!

    • @rentjeff
      @rentjeff 5 ปีที่แล้ว

      eaopanama oh no even the fuse box so no running wires to the front yee lol

  • @seventhplace
    @seventhplace 5 ปีที่แล้ว +1

    How did you determine that it was a 2 volt output on the pac?

  • @jeepersthenightstalkercree246
    @jeepersthenightstalkercree246 ปีที่แล้ว

    Can you put the link to where to buy it at

  • @jimisalgado6004
    @jimisalgado6004 5 ปีที่แล้ว +1

    Hey... thanks a lot for what you do on the channel..
    You help out so many people like myself, that need some good info

  • @Grayback1973
    @Grayback1973 3 ปีที่แล้ว

    I've had issues in the past using the radio constant 12v and ground to power LOC's. Rerouting those wires to the amp instead seems to fix it. Is there a reason why the LOC's can't share 12v constant power with the stock radio? Especially in newer vehicles.....thanks

  • @enriquetrevino7815
    @enriquetrevino7815 5 ปีที่แล้ว +1

    I'm going to install this in my trunk, question is can I just tie -wires and +positive wires into 1 rear speaker ?

    • @sBBenipal
      @sBBenipal 5 ปีที่แล้ว

      I have the same question did you figure it out?

  • @orfeous
    @orfeous 2 ปีที่แล้ว

    On my sub amp I can use high level on rca input with rca adapters. Then I get signal sensing and remote out. Then send that rear channel out from pass through to 4ch amp rear channel running my NVX XPLOC4 as passive without the DC cables.
    Front channels from LOC to front on 4ch amp of course.
    Good idea?
    6:1 step down what does that mean? My XPLOC4 says that in specifications.
    I could only get like 2v if I remember correctly last I installed it.
    How did you hook up your volt meter to measure the output?

  • @Grayback1973
    @Grayback1973 5 ปีที่แล้ว

    My Terrain has factory low level outputs before the amp(full range).I measured them at 6.5v full tilt on a 100hz sine wave.Can I just attach RCA's to those and run them straight into the amps or should I use a LOC?

  • @gabrielmorais5224
    @gabrielmorais5224 4 หลายเดือนก่อน

    Your the best man thank you nobody could do what you did I been looking for days your a live and money saver cuz they charge $100-$200 to do anything

  • @adriandiaz1381
    @adriandiaz1381 7 ปีที่แล้ว +1

    i ran into a problem while tryn to mesure the output of the lp7-4, i cant seem to get any readig on my multimeter. i used the same method as shown in the vid (6:57)...i got everything to work and its playing music fine, but i still dont know what the voltage coming out of the lp7-4 is... my multimeter was on the correct setting (V with squiggly line) but i dont know what im doing wrong, any help would be really appreciated

    • @hightide9513
      @hightide9513 7 ปีที่แล้ว

      Adrian Diaz the “V with squiggly line” is AC voltage. You need to measure DC voltage my friend. Should be V with slashed and solid line

    • @edstark44
      @edstark44 5 ปีที่แล้ว

      I have the same problem, while I can see the voltage being output by the LP7, it is very low, only 1.5v - and that’s with the gain fully cranked! I measured that while the headunit was at 75% volume. Multimeter set to AC.

  • @hammohammbbyblksheep4251
    @hammohammbbyblksheep4251 4 ปีที่แล้ว

    Hey folks I have a question I just purchased A MTX terminator two 12s in 1 boxand the amp is 1200 Watts also terminator.
    I have it in my 2003 Pontiac grand am.
    I feel like it's not beating to it's full potential so I went back over my wiring and the h-l-i cord is not hooked up.
    Am I supposed to run new wire from back of radio to the hli piece or how do I hook up that part? Please help ASAP.
    SHOULD I BUY NEW AMP OR DID I DO SOMETHING WRONG???

  • @rafaelcasero2822
    @rafaelcasero2822 3 ปีที่แล้ว

    U have several questions and cannot find a utube that is specific to
    it...
    1 - Do I have to use the Power Yellow and the Remote Blue cable if my
    Amp already has it ? Meaning all I will need to connect is the Speaker
    wire.
    2 - I have the PAC LP7-4 L.O.C. PRO Series 4-Channel device, I'm only
    going to tap in the rear speakers, so I will use 2 channel on the PAC,
    can I just twist the other two channels together ? Meaning I will use
    the White and Gray for the 2 channels, can I just twist the Green to the
    White and the Purple to the Gray for all 4 channels and then go all 4
    channels to my amp RCA ?
    3 - The the Gain on the PAC will only have the adjustment on one side which is the Right and Left Rear Or Front ? or would I need to adjust both Gains to the same ?

  • @jms7585
    @jms7585 ปีที่แล้ว

    I have a 2020 Corolla with JBL system. I’m using an Audio Control LC1i LOC for my sub setup. I have to turn the output gain fully clockwise to achieve only 3.9 volts…thoughts??? This should be able to put more voltage out. BTW, your videos are a huge educational help!

  • @terrynanomantube1
    @terrynanomantube1 3 ปีที่แล้ว

    So the power and ground that comes off of that Hook to the power and ground to the amp I have a really bad buzzing noise right when I turn off the car like really loud bass constant Would I need a tune or something to get that to Go away

  • @de_41
    @de_41 4 ปีที่แล้ว

    I talked to a tech at Pac about using this in a 2017 civic w/factory radio to connect to a RF powered sub. He said "Needs constant ground and signal from your factory speakers and it will generate the 12v turn-on". I'm confused. No remote or power???

  • @TheSuperShaan
    @TheSuperShaan 7 ปีที่แล้ว

    hello, I do NOT have a need for a remote turn on wire. Is there a benefit to buying an LP7-2 over buying the simple LP3? I simply need high to low conversion to RCA. Does the lp7 have better sound quality or something?

  • @dougo6571
    @dougo6571 5 ปีที่แล้ว

    I have a factory JBL system in my toyota. Should i splice in from the radio before the amp or after the amp or should i try to hook into the factory output of the amp for the factory subs(which this car did not come with subs). Will coming out of the amp mess with impedance causing the amp to over heat. My amp model is JBL 86280-0w622. Any input you have would be greatly appreciated. Thanks
    Doug

  • @ruffdaddy27
    @ruffdaddy27 6 ปีที่แล้ว

    So I have a question...so the LOC I HAVE JUST HAS THE 4 SPEAKER WIRES THEY GREYS AND THE WHITES THEN TWO BRWN FOR GND... BUT IF I DON'T HAVE TO STILL BEHIND THE RADIO...BY HOOKING IT UP IN MY REAR DOOR SPEAKER..DO I HAVE TO RUN WIRE FROM THE OTHER DOOR SPEAKER OR JUST ONE SIDE ND POSSIBLY JUST PUT BOTH POSITIVE N NEGATIVE TOGETHER TO GET FREQUENCY ND OUTPUT TO THE AMP?

  • @Swt96
    @Swt96 5 ปีที่แล้ว

    ineed help, i want to put MiDs on my car on 4 Doors &&, 4 Rear Deck,, im going to be usen my stock radio from my 2010 Acura TSX, can i get more info Advice on what i will be needing ? Or how would i connect the LOc

  • @danielzamora3769
    @danielzamora3769 3 ปีที่แล้ว

    Can you use this on a 2020 Harley Davidson Tri Glide Ultra instead of a DSR1 just for a base amp and the trunk of the Tri Glide

  • @rentjeff
    @rentjeff 5 ปีที่แล้ว

    hi its me again so i have 2 questions 1st is i have the 2018 charger and want to know what fuse would be best to run remote wire to if i don’t buy this kind of converter cause i have 2 the old one of this brand and a clear one so might as well put one to use unless i get one with a bass knob and my 2nd question is do i have to disconnect the noise canceling mics in the headliner? cause some stereo shops tell me i do so the subs won’t make noise and i really don’t wanna do that cause I’m use the bluetooth in my car plus i don’t wanna pay to have them install it when i know how to do it myself i might just give yall a call tomorrow if that number is still good

  • @paquesepas6696
    @paquesepas6696 4 ปีที่แล้ว

    If the oem factory head unit has 4 speakers, does the pac need 2 speakers connected to it or can I just hook up 1 speaker and which one should it be? Front left front right rear left or rear right? Does it matter?

  • @vrr2201
    @vrr2201 2 ปีที่แล้ว

    So you set the volume just before clipping and then measure the volts? or did you lower the volume when measuring the volts? Also, is the track 0 decibels or 0 decibels is achieved by turning the volume knob all the way down?

  • @srivet121
    @srivet121 5 ปีที่แล้ว

    the two line / 4 leads i would be using is high level 2ohm 32-300 htz sub leads from the factory Amp. would you see an issue with the rest of the circuit if i use the 2 / 2ohm sub leads to line in for a 2 channel amp to power the 32-300 htz 10" subs. ( i hope i asked that question right)

  • @enviouseyes
    @enviouseyes 7 ปีที่แล้ว +1

    Stock 2016 f150 snyc3 leaving factory radio running the lp7-4 into a old pioneer 4 channel amp to run all four door speakers should I cut all rca on lp7-4 harness and splice speaker per speaker in loc. Also I do not want door chime or other to be amplified so I not power the loc and run a remote from the fuse box I the am then using the rca out on my amp to run a kicker hideaway.

    • @FiveStarCarStereoInc
      @FiveStarCarStereoInc  7 ปีที่แล้ว

      +enviouseyes is it a Sony system?

    • @enviouseyes
      @enviouseyes 7 ปีที่แล้ว

      Five Star Car Stereo no Sony

    • @enviouseyes
      @enviouseyes 7 ปีที่แล้ว

      I went ahead and did install all works great fActory chimes and alert all work great. I still have some noise playing through would this be the time I connect the ground and power or will that not have any bearing on noise reduction

  • @sleepzzz800
    @sleepzzz800 4 ปีที่แล้ว

    Hey just wanted to know if you guys ever ran into this problem or if I just wired it wrong. I tapped into rear speaker wires and removed the rear speakers completely. I try adjusting the gain on the LOC and I get about 1.9v max. I get 1.9v with the gain only about half way turned up, as I turn it up more my voltage starts to drop, any ideas?

  • @trevorsapp3693
    @trevorsapp3693 3 ปีที่แล้ว

    I have a 2006 ford explorer limited and it has a 8 inch subwoofer can I hook the line out converter to that speaker wire instead of the other speakers

  • @razhocarjr
    @razhocarjr 4 ปีที่แล้ว

    If you could help me out. I can’t get rid of the static in my car hook up. And I have a popping sound when I turn my car off.

  • @ronniegilbert7692
    @ronniegilbert7692 6 ปีที่แล้ว

    I am using the lp7-4 and a kicker cxa300.4 amp that uses the DC offset turn on, do I still need need to wire the 12v constant and ground since I won't need the remote turn on?

  • @ramthaLord
    @ramthaLord 6 ปีที่แล้ว

    Hi there,
    Nice tutorial, I have an old GM Delco radio (model number: 2700), my question is all amplifier have 2v, so I need to adjust that to 2v or how to identify this? My radio works only with 10-ohm speakers, so I need to add an amplifier to work with new speaker set.

  • @sertyfy
    @sertyfy ปีที่แล้ว

    You’re a legend

  • @lanceviator2311
    @lanceviator2311 3 ปีที่แล้ว

    Quick question ...why would it have staic on some stations but not others but if u take off amp it clears up

  • @zeth15943
    @zeth15943 3 ปีที่แล้ว

    I know this is a old video but I bought this now do I need 2 sets of wires from both front speakers for a subwoofer or can I wire them together like you did off just one front speaker lead just wondering thanks

  • @MrSanpoil
    @MrSanpoil 2 ปีที่แล้ว

    So if you wire the loc next to your amplifier do you just tap into a rear speaker?

  • @jruizz1
    @jruizz1 6 ปีที่แล้ว

    do I need one of these line output converters? i am tring to hook up my stock radio to my eqs755, my problem is thei high level input has 4 wires, my radio has 8 for each speaker should i change to the low level RCA and if i do how do i hook it up with the 8 wires. thank you for any advice.

  • @eduardchavez
    @eduardchavez 2 ปีที่แล้ว

    Very very nice!!!

  • @danielpinedo9324
    @danielpinedo9324 7 ปีที่แล้ว

    I got the package sni-35 how do I connect it if I got two brown wires my ground is attached to the screw behind the radio and the 4 cable to the left and right positive and negative on the speakers but no sound from the amp and it's on?

  • @Trucker_Tim
    @Trucker_Tim 4 ปีที่แล้ว

    When reading the manual it says that I should play a 100 hz test tone when adjusting the sound output. But you play a 40 hz test tone. What hertz should I play when adjusting output sound?

  • @ptmiller98
    @ptmiller98 3 ปีที่แล้ว

    Besides cutting the brown wire off this video was great!!! That wire cuts the noise in the speakers you get when driving

  • @bryce._.mediaa
    @bryce._.mediaa 7 ปีที่แล้ว +1

    How loud can I turn up my radio

  • @cesarhernandez3275
    @cesarhernandez3275 3 ปีที่แล้ว

    Wait wait lol
    1) where did you get the ground in power from ?
    2) what would you recommend to hook up to one speaker or two speakers for the remote turn on ?

  • @arielveloz6206
    @arielveloz6206 2 ปีที่แล้ว

    Thank you so much, how you explain the installation makes it very easy and understanding to connect everything correct

  • @DOSCIOUS10
    @DOSCIOUS10 6 ปีที่แล้ว

    my amplifier is not shutting off using this Line Out Converter... Can you help me figure this out?

  • @pronoyroy1823
    @pronoyroy1823 4 ปีที่แล้ว

    Does these actually convert highs to lows?
    I want to convert 40hz subwoofer high level to low level rca to 30hz mono amp.

  • @ZEPR0FESS0RR
    @ZEPR0FESS0RR 6 ปีที่แล้ว

    When you connect the converters inputs to your cars rear speakers is it a 3 way connect where the rear speaker still work??? Even after adding this product?

  • @pete6506
    @pete6506 5 ปีที่แล้ว

    Question: I have a '18 corolla
    I have a pdx-v9 alpine amp
    I was told I can tap into the rear speakers to connect a line output converter.
    Will the Pac lp7 be the correct one to use?
    Also I will be adding a sub later to that 5 channel, will it be easy to hook up and just be a simple plug into that 5 channel for the sub ?

  • @calvinyoung9227
    @calvinyoung9227 3 ปีที่แล้ว

    Man just found your video. Let me tell you best explanation that wasn’t drawn out. Thank you Sir!!

  • @nappyh3ad83
    @nappyh3ad83 4 ปีที่แล้ว

    So is it ok to run the remote wire to the amplifier instead of the head unit or any other accessory as a power source if the LOC has remote turn on??

  • @bennymarmolejo8449
    @bennymarmolejo8449 4 ปีที่แล้ว

    I hooked it up but only getting sound out of the white rca but both speakers work?

  • @sleepzzz800
    @sleepzzz800 4 ปีที่แล้ว

    I’m only able to get about .6 max for my voltage out of the LOC, what could be my problem?

  • @vrva3138
    @vrva3138 2 ปีที่แล้ว

    Thanks!

  • @ΛευτέρηςΑλεξάκης-γ4θ
    @ΛευτέρηςΑλεξάκης-γ4θ 3 ปีที่แล้ว

    Very helpful video. One question: Can I leave the two speakers already exist, in parallel connection with the adapter? Thank you!

  • @joseorozco-alvarez3750
    @joseorozco-alvarez3750 7 ปีที่แล้ว

    What would I need to add a subwoofer and amp to a 2013 Mercedes c300 with the Harmon kardon logic 7 surround sound

  • @marrutapa7793
    @marrutapa7793 2 ปีที่แล้ว

    Grasias

  • @jasmats
    @jasmats 5 ปีที่แล้ว

    my sub just keeps clicking and the volume is very low.ive tried almost everything.

  • @johnjohn9081
    @johnjohn9081 5 ปีที่แล้ว

    Amp 8g power and ground wire to converters 14g power and ground wire?!

  • @joshhagebusch8231
    @joshhagebusch8231 6 ปีที่แล้ว

    3000 Pioneer in a 1500 w Zeus amp how do I wire it dual voice coil it

  • @robcastro5116
    @robcastro5116 3 ปีที่แล้ว

    Is there a difference in sound hooking it to two speakers then one?

  • @BadRonald1
    @BadRonald1 3 ปีที่แล้ว

    Does the LOC hook up to the front speaker outputs or the rear speaker output ?

  • @israelortiz7017
    @israelortiz7017 8 ปีที่แล้ว

    Nesesito uno de esos para ponerselo a una chevy silverado 2011 traigo el estereo orijinal pero nose cual es el adecudo y el mejor para poner un amplificador me podrar desir cual puedo usar

  • @brandonjordan559
    @brandonjordan559 5 ปีที่แล้ว

    Wat two wires do I hook the striped wire and solid white wire to

  • @kevintillack1396
    @kevintillack1396 5 ปีที่แล้ว

    How does this lp7-2 compare to the audio control lc2i

  • @TheEvilDead44
    @TheEvilDead44 7 ปีที่แล้ว

    I am going to buy the 4 channel version and and jump RCA from 4 way amp for speakers to 2 way amp for subs. Is the line level for the subs the one I should use or for the speakers? Is this going to work or do I need 2 PAC line converters 1 for speakers 1 for subs?
    LP7-> 4xRCA {line level?}-> 4 ch amp-> 2x rca jumper from 4ch amp-> sub amp

    • @FiveStarCarStereoInc
      @FiveStarCarStereoInc  7 ปีที่แล้ว

      CSK Designs no that would work, the 4 channel works just like 2-2 channels