It's amazing how much work You put to these pieces of machinery. Every button, motor and battery planned and trimmed so the one servicing this tool will have a simple job. Thanks man, keep on filming!
The Ingersoll Rand 114GQC Air Hammer th-cam.com/users/postUgkxqqoaX03nrziKwF7Bjjcc71YzLEleMvOS was just the tool I needed. I Use it to remove stuck bolts. If held at the right angle you can cut slightly into the bolt. Then turn the air hammer to where it will hammer the stuck bolt to unspin the bolt. Given a little practice it works great. This air hammer gives you the control needed to get the job done right. Very powerful yet still does not seem to have as much vibration as other guns I have used. One of the best I have gotten my hands on.
Hahaha! I am from India. Seeing the title of the video and watching the conversion of the Drill I remembered an old saying in Tamil a language spoken in the Southern part of India. When translated into English it is something like this, "Asking for the direction to a Town to which you never ever want to Go". The appropriate title would have been, "How to waste your time and money".
un tipo con tu inteligencia y conocimientos es lo que el mundo necesita, eres un artista, por ti he comprado herramientas que ni siquiera utilizo pero es que haces que se vea tan facil todo.... saludosss
few other tool restoration channels but i guarantee you are still the best and most pleasant to watch after all, keep up the good works mate ! greeting from Indonesia
По всей видимости мастер на этом видео не знает, что родному коллекторному двигателю без разницы какой ток на него приходит, переменный или постоянный. Мощность на родном двигателе конечно была бы на 30% ниже... + Жёсткости конструкции на червяке якоря, не будет, узел конструкции будет страдать от вибрации и развалиться
Согласен, конструкция так себе... Мотор на 1 подшипник установить и вибро резинки вообще жесть... Зазор над кнопкой это жесть ибо пыли там будет куча. А светодиод вообще смешно смотрится ибо бесполезный, к тому же юсб разъем вообще не в тему. Магазинные современные перфораторы с аккумулятором дороже значительно но и в разы мощнее.
Nice, but I think that over time the drive shaft form the motor will begin to slip, where you pressure fit it into the old one. I would have taken a small metal file, filed a grove in the shaft and inside the old one, and used a small metal pin to make sure it doesn't slip.
I don't think it's really an issue considering it was that good of a press fit, but I would've liked to see some red thread locker or stud holder put in there for extra insurance
Impresionante compañero......Toda una obra de arte profesional.............Felicidades............Un gran abrazo desde Las Islas Canarias (España)................
За работу лайк. Но это чисто на камеру работа. На практике этому перфу с его запрессованной шестерней на якорь другого движка будет торба после недели работ. Или прокручиваться будет или выломает в итоге
Good job. I think a failure point may be where you drilled out one shaft, and pressed the other into it. After a while of hammering, I think one shaft will begin to slip, inside the other.
Hey.. I have that EXACT model drill (@ 220V) :) This is the coolest design - looks like a gun from Judge Dredd. I believe this is the 1st model 'BoschHammer'. Also the only model ever to have HAMMER written on the chassis. (And, If I'm not mistaken, the only Bosch 'green' to have the BoschHammer name.. I think they moved the name to Bosch Professional (blue) after this one) So it's a historical unicorn in the Bosch universe :) Very good drill. Still works perfectly (I did change the grease to better grease, though. LucasOil Xtra Heavy Duty. I do that to most of my tools (: Better adhesion at high temperatures)
The thin wires are between the switch and the motor controller, they're not carrying all the current for the motor, just signals for the controller which will be much less powerful. All the high current for the motor goes from the battery through the controller and in to the motor with thicker wires.
A little idea ,maybe you can use a white plexygless cover while remove a spring for ldon't lost while remove any eject material Again amazing video.We witnessed the rescue of another drill 😀
@@corglass 😀 FYI: brushless motor is faster than brush one, although its torque is proper to fly not to drill. He gear it up for drilling but wouldn't work for a long time.
Buonasera Io ho un problema con lo stesso martello pneumatico in pratica non batte quando è freddo premetto che lo uso pochissimo è possibile che abbia bisogno di una manutenzione di questo tipo grazie
Great job been watching your videos over the years now, and they are great, and informative. Can i ask for the link to the brushless motor and controller please.
After a few years following your amazing work, I have a question that always comes to my mind after watching every project: You must have lots of storage to put all these toys away eh? Cheers!
It's amazing how much work You put to these pieces of machinery. Every button, motor and battery planned and trimmed so the one servicing this tool will have a simple job. Thanks man, keep on filming!
Thank you very much! I will do.
Service man ; This has Been TAMPERED !! WITH !! YOU'VE !! VOIDED !! THE !! LIFETIME !! WARRANTY !!
Every time I watch your next video I think to myself ‘that’s his best one yet’! Your attention to detail is fantastic. Thank you 👍
Wow, thank you! I'm glad to hear that
The Ingersoll Rand 114GQC Air Hammer th-cam.com/users/postUgkxqqoaX03nrziKwF7Bjjcc71YzLEleMvOS was just the tool I needed. I Use it to remove stuck bolts. If held at the right angle you can cut slightly into the bolt. Then turn the air hammer to where it will hammer the stuck bolt to unspin the bolt. Given a little practice it works great. This air hammer gives you the control needed to get the job done right. Very powerful yet still does not seem to have as much vibration as other guns I have used. One of the best I have gotten my hands on.
Man you're an artist. Please don't stop making such videos ❤️
I'm so glad to hear that, thank you so much!
@@gear_show well done!!
Hahaha!
I am from India. Seeing the title of the video and watching the conversion of the Drill I remembered an old saying in Tamil a language spoken in the Southern part of India. When translated into English it is something like this, "Asking for the direction to a Town to which you never ever want to Go".
The appropriate title would have been, "How to waste your time and money".
un tipo con tu inteligencia y conocimientos es lo que el mundo necesita, eres un artista, por ti he comprado herramientas que ni siquiera utilizo pero es que haces que se vea tan facil todo.... saludosss
You have a very keen eye sir! Your measurements don't seem to be precise, yet everything fits so well and neatly! Great work!
few other tool restoration channels but i guarantee you are still the best and most pleasant to watch after all, keep up the good works mate ! greeting from Indonesia
Wow, thanks! I'm so glad to hear that
I agree, it needs some kind of keyway
По всей видимости мастер на этом видео не знает, что родному коллекторному двигателю без разницы какой ток на него приходит, переменный или постоянный. Мощность на родном двигателе конечно была бы на 30% ниже... + Жёсткости конструкции на червяке якоря, не будет, узел конструкции будет страдать от вибрации и развалиться
Надо было хотя бы крыльчатку сзади снять и задний кусок вала с подшипником напрессовать
Согласен, конструкция так себе... Мотор на 1 подшипник установить и вибро резинки вообще жесть... Зазор над кнопкой это жесть ибо пыли там будет куча. А светодиод вообще смешно смотрится ибо бесполезный, к тому же юсб разъем вообще не в тему. Магазинные современные перфораторы с аккумулятором дороже значительно но и в разы мощнее.
Там наверно движок сгорел и он решил от шуроповерта поставить. Столько времени убить на это...
Да тут сборище сверхразумов...и как вам живётся с таким интеллектом ?
@@kx5hm1ez4h приблизительно на 56% лучше чем тебе
Man that is such a nice Job!
By the way, I always use wood drills for plastic, keeps them centered better 12:24 ✌️😎
Молодец, всегда смотрю переделки. Таких мастеров мало!!
Эта переделка показуха!
Nice, but I think that over time the drive shaft form the motor will begin to slip, where you pressure fit it into the old one. I would have taken a small metal file, filed a grove in the shaft and inside the old one, and used a small metal pin to make sure it doesn't slip.
if it slips, would it end up creating enough heat to friction weld?
I don't think it's really an issue considering it was that good of a press fit, but I would've liked to see some red thread locker or stud holder put in there for extra insurance
Seus videos realmente me inspiram. Muito obrigado
master craftsman supreme yet again. thank you.
Impresionante compañero......Toda una obra de arte profesional.............Felicidades............Un gran abrazo desde Las Islas Canarias (España)................
¡Muchas gracias!
За работу лайк. Но это чисто на камеру работа. На практике этому перфу с его запрессованной шестерней на якорь другого движка будет торба после недели работ. Или прокручиваться будет или выломает в итоге
Он соединение проварил за кадром)
ой , не пязди!!!
Good job. I think a failure point may be where you drilled out one shaft, and pressed the other into it. After a while of hammering, I think one shaft will begin to slip, inside the other.
Great point! I will notice that, thank you!
I agree
You should add a small wormscrew from the side.
M3x6
Good work, well done my Friend👏👏👏🤝🤝🤝
A nice and very satisfying job, one more time, it's so relaxing to watch your videos, keep doing well ! Thank you :)
Thank you, I will
This is also my opinion !
Hervorragende Arbeit, super gemacht.
Wow that is awesome. To have the knowledge you have would be incredibly handy mate. Epic video 👍🏼👍🏼
Glad you enjoyed it, thank you!
I regularly watch your videos
Thank you for always visit this channel!
Quá Đỉnh Luôn, Học Hỏi Rất Nhiều, Cảm Ơn Đã Chia Sẽ Video.👍
Отличная идея. Просто и гениально.
Excellent job above and beyond
Thank you very much!
by the thumbnail at first i have think that the drill has 22mm rails on the top 😂😂😂 nice Video 🙌🏻
Juda yahshi ajoyib 👍👏
Good video mate . Keep going . You have nice videos and content 👍
А теперь покажи, как он работает с бурами разного диаметра.
иди не базарь тут !
hello, iam from iran, your skill is very good
Genio 👍 un saluto da Cagliari.
Woa. Amazing good job bro 🥰
Thank you so much 😀
Wow, that's an incredible job.
You win man, you are king of the tool guys!
this is more than a conversion. This is a restoration, modification, improvement, and just plain art.
Yes, you're right, thank you so much!
AND ! GUTTLESS !! TOO !!
Tôi xem video của bạn đã lâu . Bạn đúng là 1 người tuyệt vời
It’s a great job, have to give a thumbs up 👍
thank you so much for the tutorial, you are amazing👍👍👍🙏🙏
Extremely impressed
عمل اكثر من رائع كل الشكر والتقدير لك من اليمن
Hey.. I have that EXACT model drill (@ 220V) :)
This is the coolest design - looks like a gun from Judge Dredd.
I believe this is the 1st model 'BoschHammer'. Also the only model ever to have HAMMER written on the chassis.
(And, If I'm not mistaken, the only Bosch 'green' to have the BoschHammer name.. I think they moved the name to Bosch Professional (blue) after this one)
So it's a historical unicorn in the Bosch universe :)
Very good drill. Still works perfectly (I did change the grease to better grease, though. LucasOil Xtra Heavy Duty. I do that to most of my tools (: Better adhesion at high temperatures)
Maybe interesting to know;
The 220V version is also 420W.
Higher voltage, but less Amps
Pěkná práce. Hned při prvním testu. Jde od baterky jiskra.
great job master, greetings from Mexico
Thank you very much!
Absolutely lovely. Thank you for sharing.
Brushless!!! Great conversion. You are very skilled!
Wow, thanks!
FLEA ! POWERED !! BRUSHLESS !! USELESS !! MOTOR !!
Would u mind sharing the links for the motor and driver?
Excelente trabalho 👏👏👏
I like your technique & very good mind, ausom job
After you wash the parts you should put a little bit of oil or grease on them so this way there not going on dry during the assembly
sir why you use small wires of controller switch they can't heated when drill is running i confused 🤔 about these connection kindly clear them
The controller switch does not controll the current of the motor, the wires only cary a little bit of power
The thin wires are between the switch and the motor controller, they're not carrying all the current for the motor, just signals for the controller which will be much less powerful. All the high current for the motor goes from the battery through the controller and in to the motor with thicker wires.
@@danielmihaylov69 love you sir i understand your beautiful answer thanks 🌹
@@kaelkramer1259 love you sir for you answer 💕💕
Top demais! Parabéns pelo trabalho!
Комментарий в поддержку канала и ролика, а также труда мастера.
好強...只能用欣賞的角度來看了 讚
Great job, thank you brother. You are so talented
You're welcome, thank you so much!
Thanks so much for the great vids. Super useful and inspiring, I'd like to learn to do this myself.
excelent work. congratuletions.
Mi of México City.
Thank you very much!
Excellent job 👌👌👍👍
Where I can buy these motor and controller please tell🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏
Please provide a link
A little idea ,maybe you can use a white plexygless cover while remove a spring for ldon't lost while remove any eject material
Again amazing video.We witnessed the rescue of another drill 😀
Thanks for the tip!
Good job. Great engineering.
Thank you very much!
What Engineering was Really Done ! ?? Other Than PUTTING A !.FLEA ! POWERED !! MOTOR ! IN ! IT !!
Amazing engineering.
Very proper conversion 😍 may I know the different in power watt,torque,rpm after conversion?
Why?
@@corglass 😀 FYI: brushless motor is faster than brush one, although its torque is proper to fly not to drill. He gear it up for drilling but wouldn't work for a long time.
Hello, the plexiglass box Is the cover vintage discplayer ?
Yes, you're right, it is the cover vintage disc player.
@@gear_show 😂😂😂 good, and good work, I write from Italy and my english Is very bad. You are a very good maker, thank for replay.
Which type of motor is used and where it was available motor control
Buonasera Io ho un problema con lo stesso martello pneumatico in pratica non batte quando è freddo premetto che lo uso pochissimo è possibile che abbia bisogno di una manutenzione di questo tipo grazie
Very good, you are a genius
Many many thanks
лайфхак тебе на будущее, очищать от смазки хорошо керосином, а не мамкиным порошком для посудомойки
Great job been watching your videos over the years now, and they are great, and informative.
Can i ask for the link to the brushless motor and controller please.
After a few years following your amazing work, I have a question that always comes to my mind after watching every project: You must have lots of storage to put all these toys away eh? Cheers!
Yes, you're right, I have a lot of power tools in my workshop.
Красавчик, шикарная работа.
Really good job. Chapeau bas!
Thank you!
Parabéns pelo seu trabalho ficou muito bom obrigado por compartilhar com as pessoas o seu conhecimento
Very good👍👍
Thanks for the visit
Hi Gear Show could you please put the link of the brushless motor?
Meus parabéns ficou excelente. Você é muito minucioso no que faz ✌️👏👏
Ta vidéo super bien 👍
sevginin sonucu; herzaman olduğu gibi Mükemmel ! iyi işler yapmaya devam et dostum.
Teşekkür ederim! Yapacağım.
Absolutely mind blowing work thank you sir 😊👍.
I'm so glad you like it, thank you!
Good work 👍👍👍👍👍
Thanks you Great Watch Vidéo 🥰🥰🥰🥰
Excellent restoration 👍👍👍Thank you for sharing. Be safe🇨🇦
Thanks, you too!
Where I should buy a circuit board for the battery???
Really well done 👍👍👍
professional very good,,,👏👍
Einfach perfekt 😋👍
Good job 👍
The link where you bought the brushless motor
Very professional work, Thanks my friend
Many thanks, you're welcome
nice work i like it
Tôi cảm thấy bạn là người có sáng tạo hơn tôi!
good job Brooo! 👌
RPM of this motor and can this motor is used for making cordless circular saw and angle grinder
excellent work
can you provide brushless motor details with link to buy the motor
A Grandmaster!!!!🇵🇷👍💯✋!!!
🔥 Amazing
Dang that motor is really stronk... 💪
Yes, it is.
Very nice and useful
Молодец, конечно. А через сколько мотор выпрыгнет из бочины?
nicely done!
Thanks for the visit
top bro!!! tell me where to buy this controller for brushless motor please!!
where did u get motor form