562 is an excellent saw still have 3 of them. 2 of them are 2016’s bought new together and both have never been apart. They’ve cut ALOT of wood and been very reliable.
She's got power that's for sure, but it does struggle a bit which is totally expected of a 60cc saw sporting a 36inch bar. Still impressive for stock! Would like to see a fully ported 562 wearing that outfit.
Mr. Boedy, I may have missed it, are you doing a re-boot on the Auto-tune and M-tronic saws before the cuts? I watched the STIHL MS 400 36"vid as well. While the process is somewhat different for both saws, the cut times might be different if the saws are tuned with the 36" bars "before" the timed cuts...just curious about your methodology....thank you sir...
Just got my brand new 562 back from top tier builder/ porter and yes it screams, but my stock 372 pulled 24" buried in red oak much better. Made a mistake trying to replace 372 w hopped up 562. Picked up new Dolkita 7900. WAY more saw than my 372 was, feels about the same weight/ handling wise. I dont miss my 372. 562 now fills my 60cc role EXTREMELY well!
You finally did it, thanks! Definitely gonna buy it in the future. You could give a try of that HTSS(Walt/afleetcommand) bulit, so setting the squish right about 20 thousand, MM and that pop up piston, because everyone one can do these simple stuff at home, and then port it that would be awesome comparison. And since You going to port it You will be doing the squish and MM anyway so not that extra time anyway. Greetings Kuba
@@Szczyrczek well we have a lot of pine down here in Louisiana and to me it’s like a hot knife through butter even on hardwood with that saw. My tach I have on it is close to 17k RPM. The porting, gutting the stock muffler/dual outlet was done by me and the pop up piston I bought from lil red barn. It’s a screamer lol. I’d like to put it up against Cajuns 562 which is a hell of a screamer just to see how I compare.
Maybe one day you could tie strap a 10X10 bunch of 4X4s together and do a time comparison of at least three cuts for each of the three saws with the same bar and chain swapped out? That's the way redbull661 channel used to check their setups.
Well done! I prefer not for rpm go down so much, the saw struggles an might not be able to keep on going for as long as you like. Just my oppinion, thx 😊👍
I’d be careful with a new saw running a 36in bar gets way too hot on the crank bearings will burn it up quicker I’ve rand a 562for years felling timber loves a 24 no more
@Novice Lumberjack fair play... better than thought you must have got a strong one, slightly impressed. Though that's. 0.50 gauge, we only tend to use long bars in that gauge for milling, I can't imagine continuous cuts with that bar on that saw, stratos tend to run hot and go slower after multiple cuts in big timber ..can't see that saw lasting that long or if chain goes dull ... lots of problems with those saws failing here with short bars🤷🏻♂️
Very impressive 60cc saw. I have been wanting a 562. I have NO idea why. I am a firewood cutter, My 2 main saws are a Makita 7901 which I keep a 22" bar on, my other main saw is my 390XP which usually has a 28 on and also I have a 36 for. WHY do I want another saw when I already have like 10 or more? I don't know, Chainsaw addiction for sure.
Oh I also keep a Husqvarna 450(yeah I know), that I keep a 16" on for clearing ATV trails, I been thinking of getting a 550XP to replace it but WHY??? The 450 does fine for what I use it for, always starts but why do I want a 550 and 562, I can;t justify it at all but I sure want.
That's a stout saw for being that size I'm fixing to take my 372 get some fire wood trying out a new chain it's a orgeon skip tooth square ground chain see how it does to my hand filed square keep up the good videos
Husqvarna is the JV and Stihl is the Varsity. That is just the way it is and that is the way it's going to be. What more could I possibly say, STIHL RUNS THE YARD. 😊👍🏿👑👑👑👑👑👑👑💪🏿 #stihlpower #stihlisyourdaddy #stihlrunstheyard
@@novicelumberjack I'm glad that you are smiling. You should see the smile on my face when I'm using the Gold standard in chainsaws Stihl. Especially when I'm using the 500i. It's good to be the King. STIHL RUNS THE YARD. 😊👍🏿👑👑👑👑👑👑 #stihlpower #stihlisyourdaddy #stihlrunstheyard 😊😊😊😊😊😊😊😊😊😊
How was it modded? If you did a base gasket delete and raised the exhaust with some hogged lowers it would lose power. Sometimes,”modded”. Is less power if it was done in a certain fashion
562 is an excellent saw still have 3 of them. 2 of them are 2016’s bought new together and both have never been apart. They’ve cut ALOT of wood and been very reliable.
Hey Bohdy, if you hold your left hand slightly to the right on the top handle, it will help you to not cut out of the wood.
She's got power that's for sure, but it does struggle a bit which is totally expected of a 60cc saw sporting a 36inch bar. Still impressive for stock! Would like to see a fully ported 562 wearing that outfit.
My 7yo son is watching over my shoulder. He said haha he missed the cut! You are entertaining guys of all ages 😂
Crazy how well it pulled that and on it's first tank to boot.
I only have a 460 but it became more fun when I went from 24 down to an 18 inch bar. That 562 might be scary fun with a 18 or 20 inch bar.
Best thing to do
I only run smaller bars on powered/pro saws
Cuts beautifully
Mr. Boedy, I may have missed it, are you doing a re-boot on the Auto-tune and M-tronic saws before the cuts? I watched the STIHL MS 400 36"vid as well. While the process is somewhat different for both saws, the cut times might be different if the saws are tuned with the 36" bars "before" the timed cuts...just curious about your methodology....thank you sir...
Just got my brand new 562 back from top tier builder/ porter and yes it screams, but my stock 372 pulled 24" buried in red oak much better. Made a mistake trying to replace 372 w hopped up 562. Picked up new Dolkita 7900. WAY more saw than my 372 was, feels about the same weight/ handling wise. I dont miss my 372. 562 now fills my 60cc role EXTREMELY well!
Yeah, displacement is king.
Great vid. Keep it up.
Could you make another cut with both in the new size log
Awesome video!
Best regards!
Oh man, I felt for you when it broke through. Sometimes I cut with a hand bow saw and end up 30 degrees off vertical.
Hey Nov, question: I’ve got an old Sears PS 3.7hp (60.6cc). Based on what the 372 just did, shouldn’t my old saw pull a 36 inch bar?
that's a badass chainsaw
You finally did it, thanks! Definitely gonna buy it in the future. You could give a try of that HTSS(Walt/afleetcommand) bulit, so setting the squish right about 20 thousand, MM and that pop up piston, because everyone one can do these simple stuff at home, and then port it that would be awesome comparison. And since You going to port it You will be doing the squish and MM anyway so not that extra time anyway.
Greetings
Kuba
I'll be diving deep into this thing. But it takes me time. I'm slow.
@@novicelumberjack I get that, thank You for Your work and time Boedy!
I’ve got a pop up in mine, dual exhaust muffler mod, gasket delete, ported and a 20” Tsumura with husky full skip chain.
@@ohsnap46841 May I know why do You use full skip? How do You like 562xp? Whobdid port job for You!
@@Szczyrczek well we have a lot of pine down here in Louisiana and to me it’s like a hot knife through butter even on hardwood with that saw. My tach I have on it is close to 17k RPM. The porting, gutting the stock muffler/dual outlet was done by me and the pop up piston I bought from lil red barn. It’s a screamer lol. I’d like to put it up against Cajuns 562 which is a hell of a screamer just to see how I compare.
Maybe one day you could tie strap a 10X10 bunch of 4X4s together and do a time comparison of at least three cuts for each of the three saws with the same bar and chain swapped out? That's the way redbull661 channel used to check their setups.
Well done! I prefer not for rpm go down so much, the saw struggles an might not be able to keep on going for as long as you like. Just my oppinion, thx 😊👍
I’d be careful with a new saw running a 36in bar gets way too hot on the crank bearings will burn it up quicker I’ve rand a 562for years felling timber loves a 24 no more
👍👍
I like my little Echo cs590. However I really want an angry husky thank you for the video
The 562xp will improve after about 5 more tanks.
Pretty impressive for a 60cc saw. Full comp chain? Looks that way. How's the oiling?
Doubt, that's a full house chain, probably a skip 0.50 gauge? Or 0.58?
Full comp, C83
@Novice Lumberjack fair play... better than thought you must have got a strong one, slightly impressed. Though that's. 0.50 gauge, we only tend to use long bars in that gauge for milling, I can't imagine continuous cuts with that bar on that saw, stratos tend to run hot and go slower after multiple cuts in big timber ..can't see that saw lasting that long or if chain goes dull ... lots of problems with those saws failing here with short bars🤷🏻♂️
It's funny to hear you say the 562 is "close" to the 400 that's awesome. Says alot really.
👍🆙BigGuy
It just looks better too Bro Namath.
So the 562 xp is a large mount bar, how did it oil?
Seemed to do perfectly fine. The bar didn't get burnt up at the bottom. I had the oiler turned all the way up.
Very impressive 60cc saw. I have been wanting a 562. I have NO idea why. I am a firewood cutter, My 2 main saws are a Makita 7901 which I keep a 22" bar on, my other main saw is my 390XP which usually has a 28 on and also I have a 36 for. WHY do I want another saw when I already have like 10 or more? I don't know, Chainsaw addiction for sure.
Oh I also keep a Husqvarna 450(yeah I know), that I keep a 16" on for clearing ATV trails, I been thinking of getting a 550XP to replace it but WHY??? The 450 does fine for what I use it for, always starts but why do I want a 550 and 562, I can;t justify it at all but I sure want.
there is some newer 562 come with dished piston.
All the 562 saws ive had the pistons were domed pistons the only things that changed were the carbs
My stock 562 piston was a flat top.
@T. Jussilainen, you are very correct sir and know HUSQVARNA well..
DAYYYUMM! I gta get one...
Hard to compare to the echo 590/620, they are made more for torque, 562 higher hp & rpm, I run both, killer saw but has its place for sure
That's a stout saw for being that size I'm fixing to take my 372 get some fire wood trying out a new chain it's a orgeon skip tooth square ground chain see how it does to my hand filed square keep up the good videos
Hi Mr Novice, I just want to know Stihl vs Husqvarna which one is better chainsaw, because im looking to buy chainsaw this summer
Thanks
They (and echo) all make great saws.
I'd start with stating how big of a chainsaw you need, what kind and size wood you will be cutting.
Dealer support also critical.
What a beast for stock!
Yeah man, I am totally impressed.
They pull all day at 24 but I found myself using 20 and 18
Husqvarna is the JV and Stihl is the Varsity. That is just the way it is and that is the way it's going to be. What more could I possibly say, STIHL RUNS THE YARD. 😊👍🏿👑👑👑👑👑👑👑💪🏿 #stihlpower #stihlisyourdaddy #stihlrunstheyard
Ya know...I am growing to like your little rants. Seriously. I am smiling from ear to ear right now! 😃 😊 🙂 😀 😄
@@novicelumberjack I'm glad that you are smiling. You should see the smile on my face when I'm using the Gold standard in chainsaws Stihl. Especially when I'm using the 500i. It's good to be the King. STIHL RUNS THE YARD. 😊👍🏿👑👑👑👑👑👑 #stihlpower #stihlisyourdaddy #stihlrunstheyard 😊😊😊😊😊😊😊😊😊😊
And you are a brainwashed dipshit,
Y'know, I haven't ever seen anyone put a mini turbo on a chainsaw before... Hmm...
67cc vs 59 cc why..folks and comparisons should only be done stock no saw is modified the same.
After the muff mod and break in its going to eat that still 400
Yep absolutely will
59.8 cc
Way to make a saw cry. ???
Just because it can pull a 36 inch bar doesn’t mean you should.
Mean saw, makes me wanna trade up!
Ehhhh now ya lost me Boedy. I done had a modded 562 and it wanted no real part of a 36” bar
Ya lost me bud
Whatya mean? I simply put the bar on and cut a chunk of wood. Where did I lose you?
How was it modded? If you did a base gasket delete and raised the exhaust with some hogged lowers it would lose power. Sometimes,”modded”. Is less power if it was done in a certain fashion
@Cajun Hello I have seen some of Your amazing work. If I may ask, Is BGD, MM, and pop-up piston gut idea for a bit more grunt?
@@Szczyrczek not hardly noticeable in my opinion
@@cajun3197 many thanks!
Too big of a bar you're pushing it too hard!