Thank you for the step-by-step guide. It took me 4 hours straight to get it installed, but I wouldn't have been able to achieve it without your detailed instructions. I'm really grateful!
Just did this in my daily work car and it took about 30-35 minutes total by using the method where you drill out the tabs. I watched this video to see how you routed the cables. Nice job!
Great dismantling aid vid - thanks! For everyone thinking of doing this remember, as ALL the instructions in manuals and TH-cam say : YOU MUST UPDATE YOUR FIRMWARE BEFORE INSTALLING THE NEW HUB UNIT. The only improvement I would make (and I may) is to show the location of all the trim retaining pins/clips for each bit removed. That way us noobs know where to apply those trim tools effectively. Great video - good perseverance, don't forget to tie back those unused connectors and remove your SD Navigation card from the old unit (if you have one) - Cheers!
@@ErickAngeles-x3f I've seen on most reddit post that you could "break the CMU" and have to get a whole new Mazda display part. It might also not be able to recognize the new part and not function properly...I'm currently in the process of downloading the files to update my Mazda :(
Great video. Thanks for the info. Inspired me to change out mine. However, it is easy to remove the face plate of the old USB unit (more recent video) which does save alot of time ripping up the center console. But hats off to you and your effort. Great information.
Thanks. I also have the 2016 and have this module waiting to be installed. I saw another video where the guy drills out the tabs to avoid taking off the center console but I rather not go that route. This video should help.
I actually thought destroying the old one too. I just was not confident that I would not break the dash frame around the old module. Turns out, taking things apart is not that bad once you know where the pins and screws are.
@@GearGadgetExperiments Thanks again. Finally banged out the Carplay upgrade. Took me about two hours because I take my time and I was trying to avoid taking out the center console. Just a note for anyone doing this, taking out the center console is really not that much work and makes is much easier so just go for it. Also you gain some extra work space if you pull out the glove box, and while you are there you can change or clean your cabin air filter. One thing I am not sure about but I moved the navigation SD card over to the new modules and I no longer have access to the built in maps. Even though I was using my phone for navigation I still liked that I had access to maps as a backup. I am not sure if the SD card was tied to the old module (I think they may be) or if you lose the ability to have mapr period. I may order a off market SD card and see if I have access again. But yeah, to anyone reading just take the entire thing off, and be careful, I dropped the 10mm bolt and will have to go in at some point to either recover and or replace the bolt, but everything did snap in.
@@smoothy569 "Mazda CarPlay/Android Auto Install Hack" the guy drills through the stock unit to break off tabs. To be honest taking off the entire center console is not that hard and really does not take that much time. I now have the stock USB box sitting in a box just in case I everneed to swap it back in. The only regret I have is beeing too lazy to go find my magnetic wand to put the 10mm screw back in the end (but it really has not ben a problem).
I might get a 2016 Mazda 3 today and I was worried about the lack of CarPlay, this will solve the issue. A little bit of more work that I was expecting but the actual module isn’t expensive
I picked up the car, it doesn’t have the CD player so it has the module in the same spot as yours, also the firmware of MazdaConnect it’s not updated, I had to make an appointment on my local Mazda dealer to get it updated first (no way I’ll pay them $500 for do the whole thing, I’m just paying for the update).
@@GearGadgetExperimentsNo, the dealer charged $60 for the update but I bought the module and installed following your video, the hardest part was pushing the bottom tabs of the module to release it, basically you’re working blind until you hit the tabs. Thank you for the video, it was very useful.
Thanks for a very good explanation and step by step instruction. But I have one question why are we adding one if we are going to dangle one more in the end. Aren't they same? Can't we use original cable instead of adding blue/green from the package?
Followed this video to the letter! Thank you! Worked a treat although there were a couple of heart racing moments once I had completed it. The screen came up with a Hybrid System Malfunction error which had me sweating bullets, but little bit of system down time reset things and we were all good again. Until...I went to put it in reverse and the camera wouldn't work! Holding mute+NAV+back forced the infotainment system to do a hard reboot which solved that issue too. Only other issue that I can't seem to find a fix for is that the touchscreen doesn't work when using Android Auto (I don't have an iPhone to see if Carplay is the same). Anyone else have that issue? Is that just the way it is, or have I missed a setting somewhere? Touchscreen works fine outside of AA.
Glad it worked! My son has a non working touchscreen. He says it is not worth fixing because Mazda disables it while the car is moving any. Is that what you are seeing?
@@GearGadgetExperiments Yeah, the default system from Mazda works while parked and driving at less than 5km/h but even when parked, AA doesn't have touchscreen functionality. Looks like it's just the way Mazda Connect and AA speak to each other, and from I've just been reading, both parties are pointing the finger at the other saying it's their fault. Maybe a firmware update will address the issue in the future. Thanks again for the tutorial video.
My son doesn't have any complaints about the unit itself. He hates that Mazda doesn't allow you to use the screen while the car is in motion. You have to use the selection wheel. He is very happy to have CarPlay in his car.
i have thought some short cut. Just put the new box inside the compartment or behind those control knob and just disconnect the old one from the screen and connect the new one.
Hey! Just a question, what size was the socket extension you were using for this installation? Only thing left for me is to buy an extension and I’m afraid of getting a short one.
I did this into my mazda3 2018. The installation was pretty easy. The problem I have is the entertainment function is now disabled and there is no FM radio into the android box. Any idea on how to enable the entertainment function and I have access to the Mazda FM feature?
Hi, I did everything as following the video instructions, but now my reverse camera is not showing up on the display when I shift into reverse 😢 do you know what is happening? The only cable that I didn't connect was the green adapter one. Thanks!
I did not see this issue. I first would try to unplug the connectors and see if any of them were bent out of place. Then re-seat them to make sure they all have good connections.
Quick question, the touch screen only works when the car is stationary, do the non touch controls work with apple car play, like the dial behind the gear lever and the steering wheel buttons? or can you only adjust, say, the song choice with your phone while you're driving?
Having no touch screen will indeed limit the ease of use. But the dial knob and steering wheel buttons will still work. The dial can control your CarPlay apps, but it is not as good as a touch screen
nice video mate im in australia and have a madza 3 2017 model and i upgraded firmware to 70 and have no auto andriod so this process should work for me , i just not keen to have to pull the car apart lol
@@GearGadgetExperiments HI mate i did the install it all went fine however auto andriod wont start , its a option in the menu now but its greyed out , i fear its because i updated my firmware a few weeks ago , would u have any ideas ?
@@GearGadgetExperiments i updated my firmward weeks ago before the hub install as i was getting a few some issues , i think i've fixed it thou with using a different cable as its now installed and working but when i bump the cable it disconnects so will order a better cable and see how it goes
@@Casper_Brisbane Oh, yes. Quality cables make a big difference for data transfer. Lower quality cables can charge ok, but sometimes struggle with data transfer. Looks like you solved your problem.
Read the other comments. I viewer put a link to a video that shows how to update the software . Seems to work for them. My son updated his software so I didn't have to do it.
Hello, your Amazon link shows that it's currently unavailable. Is there another one you recommend? I have a 2015 Mazda 3 hatchback. I really appreciate any help you can provide.
I followed your exact steps and got it all installed, have 70.00.100 installed (did that first) and it’s all up and running, but CarPlay isn’t working! Does anyone have any thoughts on this? I did a system reset to try to fix it but the CarPlay and android auto applications are completely greyed out and I can’t figure it out…
I have a 2018, I didnt take out the center console. I could get the top two legs with the long screw driver. For the lower legs, I went down where the pedals are, I removed the forward panel, then the lower air duct. From there I was prying with the screwdriver when the legs are and eventually I got it.
@@GearGadgetExperiments I'm actually still doing it right now. I'm routing the cable on the left side instead of the right because of the blendoor/ac actuator. I think it's for the dual climate. I don't want the wires to ever get in the way.
Couldn’t you just update the firmware to the latest and it add Apple CarPlay and Android auto? I think there’s a couple videos on TH-cam on how to do this. No need for installations
There was a time that i thought you were going to take out the engine too😂😂
I definitely had to pull out more than I was planning! Haha. But it wasn't too bad.
😂
Thank you for the step-by-step guide. It took me 4 hours straight to get it installed, but I wouldn't have been able to achieve it without your detailed instructions. I'm really grateful!
Glad you got it in!
Using your video I was able to successfully complete my install on my 2016 Mazda 3. Thanks for making a great video!
Happy to help!
Just did this in my daily work car and it took about 30-35 minutes total by using the method where you drill out the tabs. I watched this video to see how you routed the cables. Nice job!
Great dismantling aid vid - thanks! For everyone thinking of doing this remember, as ALL the instructions in manuals and TH-cam say : YOU MUST UPDATE YOUR FIRMWARE BEFORE INSTALLING THE NEW HUB UNIT.
The only improvement I would make (and I may) is to show the location of all the trim retaining pins/clips for each bit removed. That way us noobs know where to apply those trim tools effectively. Great video - good perseverance, don't forget to tie back those unused connectors and remove your SD Navigation card from the old unit (if you have one) - Cheers!
I’ve been wanting to do this and I was wondering what were to happen if you don’t update your Firmware and just do it like he did?
@@ErickAngeles-x3f I've seen on most reddit post that you could "break the CMU" and have to get a whole new Mazda display part. It might also not be able to recognize the new part and not function properly...I'm currently in the process of downloading the files to update my Mazda :(
I watched lots of other videos, but only your video was helpful since we have the same module to change. Thanks god, finished successfully
happy to help!
Great video. Thanks for the info. Inspired me to change out mine. However, it is easy to remove the face plate of the old USB unit (more recent video) which does save alot of time ripping up the center console. But hats off to you and your effort. Great information.
Thanks. I also have the 2016 and have this module waiting to be installed. I saw another video where the guy drills out the tabs to avoid taking off the center console but I rather not go that route. This video should help.
I actually thought destroying the old one too. I just was not confident that I would not break the dash frame around the old module. Turns out, taking things apart is not that bad once you know where the pins and screws are.
@@GearGadgetExperiments Thanks again. Finally banged out the Carplay upgrade. Took me about two hours because I take my time and I was trying to avoid taking out the center console. Just a note for anyone doing this, taking out the center console is really not that much work and makes is much easier so just go for it. Also you gain some extra work space if you pull out the glove box, and while you are there you can change or clean your cabin air filter. One thing I am not sure about but I moved the navigation SD card over to the new modules and I no longer have access to the built in maps. Even though I was using my phone for navigation I still liked that I had access to maps as a backup. I am not sure if the SD card was tied to the old module (I think they may be) or if you lose the ability to have mapr period. I may order a off market SD card and see if I have access again.
But yeah, to anyone reading just take the entire thing off, and be careful, I dropped the 10mm bolt and will have to go in at some point to either recover and or replace the bolt, but everything did snap in.
Glad it worked out for you. I would just leave the bolt in there if it is not rattling. haha
Do u remember what that video is called?
@@smoothy569 "Mazda CarPlay/Android Auto Install Hack" the guy drills through the stock unit to break off tabs. To be honest taking off the entire center console is not that hard and really does not take that much time. I now have the stock USB box sitting in a box just in case I everneed to swap it back in. The only regret I have is beeing too lazy to go find my magnetic wand to put the 10mm screw back in the end (but it really has not ben a problem).
Good thing that these mazda variants are not that common. Usually, the usb box is in the armrest compartment.
Yes, the armrest ones are easier. A few less steps.
I might get a 2016 Mazda 3 today and I was worried about the lack of CarPlay, this will solve the issue. A little bit of more work that I was expecting but the actual module isn’t expensive
It is less work if the usb module is in the center armrest. Half the mazda 3's have it there.
@@GearGadgetExperiments Thank you, I'll check that when I get the car delivered.
I picked up the car, it doesn’t have the CD player so it has the module in the same spot as yours, also the firmware of MazdaConnect it’s not updated, I had to make an appointment on my local Mazda dealer to get it updated first (no way I’ll pay them $500 for do the whole thing, I’m just paying for the update).
@@paradisopaulwill the dealer do it for free? see comments from others to see how people have updated by themselves for free.
@@GearGadgetExperimentsNo, the dealer charged $60 for the update but I bought the module and installed following your video, the hardest part was pushing the bottom tabs of the module to release it, basically you’re working blind until you hit the tabs. Thank you for the video, it was very useful.
Do we need to update Firmware ?
Does anyone have issues connecting usb to the hub?
Excellent tutorial. Thank you!
Thanks for a very good explanation and step by step instruction. But I have one question why are we adding one if we are going to dangle one more in the end. Aren't they same? Can't we use original cable instead of adding blue/green from the package?
Old one does not have CarPlay.
@@GearGadgetExperiments sorry, I meant the cable which comes with new usb hub, not the hub itself.
@@LevaniCh1they are not exactly the same. I'm sure the new cable wiring was necessary to implement the CarPlay
Followed this video to the letter! Thank you! Worked a treat although there were a couple of heart racing moments once I had completed it. The screen came up with a Hybrid System Malfunction error which had me sweating bullets, but little bit of system down time reset things and we were all good again. Until...I went to put it in reverse and the camera wouldn't work! Holding mute+NAV+back forced the infotainment system to do a hard reboot which solved that issue too. Only other issue that I can't seem to find a fix for is that the touchscreen doesn't work when using Android Auto (I don't have an iPhone to see if Carplay is the same). Anyone else have that issue? Is that just the way it is, or have I missed a setting somewhere? Touchscreen works fine outside of AA.
Glad it worked! My son has a non working touchscreen. He says it is not worth fixing because Mazda disables it while the car is moving any. Is that what you are seeing?
@@GearGadgetExperiments Yeah, the default system from Mazda works while parked and driving at less than 5km/h but even when parked, AA doesn't have touchscreen functionality. Looks like it's just the way Mazda Connect and AA speak to each other, and from I've just been reading, both parties are pointing the finger at the other saying it's their fault. Maybe a firmware update will address the issue in the future. Thanks again for the tutorial video.
Happy to help
13:23 oh man I wish you showed how you replied it. I’m left with an extra cable and it’s not a replaced usb one :(((
Hi I am curious as to how this aftermarket hub has held up after 7 months any bothersome issues? Imput would really be appreciated :)
My son doesn't have any complaints about the unit itself. He hates that Mazda doesn't allow you to use the screen while the car is in motion. You have to use the selection wheel. He is very happy to have CarPlay in his car.
There’s a option in the Bluetooth settings to turn it to always on
i have thought some short cut. Just put the new box inside the compartment or behind those control knob and just disconnect the old one from the screen and connect the new one.
Hey! Just a question, what size was the socket extension you were using for this installation? Only thing left for me is to buy an extension and I’m afraid of getting a short one.
6 inch should be enough
Would that middle piece where cup holders are be easier to take out if one of the seats was removed ?
I don't think the seats matter much
Can you still use the steering wheel controls such as volume and skipping songs?
yes
I heard you have to upgrade the firmware before installing the CarPlay module
Only if you are not already running the minimum spec firmware. Check the product details to determine what is needed.
This was entertaining 😂
Do you know if the Bluetooth calling and music functions still work like the normal version? Without connecting the cable?
Yes. Everything else works the same when not in CarPlay mode.
I did this into my mazda3 2018. The installation was pretty easy. The problem I have is the entertainment function is now disabled and there is no FM radio into the android box. Any idea on how to enable the entertainment function and I have access to the Mazda FM feature?
Sorry, I don't. My son does not have this issue is his car. Did you update the firmware as recommended by the seller?
Hi, I did everything as following the video instructions, but now my reverse camera is not showing up on the display when I shift into reverse 😢 do you know what is happening? The only cable that I didn't connect was the green adapter one.
Thanks!
I did not see this issue. I first would try to unplug the connectors and see if any of them were bent out of place. Then re-seat them to make sure they all have good connections.
Quick question, the touch screen only works when the car is stationary, do the non touch controls work with apple car play, like the dial behind the gear lever and the steering wheel buttons? or can you only adjust, say, the song choice with your phone while you're driving?
Having no touch screen will indeed limit the ease of use. But the dial knob and steering wheel buttons will still work. The dial can control your CarPlay apps, but it is not as good as a touch screen
What's the audio quality like? Distortions, static anything of that sort after 10 months of use?
works like day 1.
Did you need a firmware update?
did you update yours? planning on just installing but I am not sure.
@geargadgetexperiments Do you know if this upgrade also improves the performance of the charging ports?
Sorry, I don't know if it is any better.
It does, 2amp charging. Much faster.
Would you happen to know if this would work for my 2014 Mazda 3? It is Gen 3 - the interior looks just like yours?
Nvm im silly this is just where tou plug it in not the screen, im sorry.
Great video man! one question did you lost touch screen functionality?
The touch screen was lost before the install. My son said it was not that useful anyway since it does not work while car is moving.
I want to install it on my miata, does it work great like the oem one ?
It has given us no issues. I don't have an OEM to compare it to
nice video mate im in australia and have a madza 3 2017 model and i upgraded firmware to 70 and have no auto andriod so this process should work for me , i just not keen to have to pull the car apart lol
it is not that hard :)
@@GearGadgetExperiments HI mate i did the install it all went fine however auto andriod wont start , its a option in the menu now but its greyed out , i fear its because i updated my firmware a few weeks ago , would u have any ideas ?
Did you upgrade to the firmware listed on the seller's page? Did you try updating firmware with the New adapter present? Just some thoughts...
@@GearGadgetExperiments i updated my firmward weeks ago before the hub install as i was getting a few some issues , i think i've fixed it thou with using a different cable as its now installed and working but when i bump the cable it disconnects so will order a better cable and see how it goes
@@Casper_Brisbane Oh, yes. Quality cables make a big difference for data transfer. Lower quality cables can charge ok, but sometimes struggle with data transfer. Looks like you solved your problem.
When you install this, do the dials and steering wheel buttons work to navigate and make calls and everything or do you have to use the touchscreen?
Dials still work. Touchscreen will still not work while you are moving. Haha
Is there a way to make it work while it’s not in park?
I installed the adaptor on my mazda-3 2015 , its charging but the CarPlay is not working what could be the problem please ? 14:22
Did you update the software to minimum that the manufacturer specified?
@@GearGadgetExperiments I wasn’t aware about this , how can i update it ? Can i do it my self or should i go to someone specialised ?
Read the other comments. I viewer put a link to a video that shows how to update the software . Seems to work for them. My son updated his software so I didn't have to do it.
@@GearGadgetExperiments 👌🏻
What's the audio quality like? After 10 months of use, is it still working good? Do you notice any distortions, static etc?
still works like day 1.
Hello, your Amazon link shows that it's currently unavailable. Is there another one you recommend? I have a 2015 Mazda 3 hatchback. I really appreciate any help you can provide.
Sure, this is actually the same thing. amzn.to/4acJchp . Good luck. Don't forget to update your software.
LOL i would definitely break something if i do that and feels like paying the dealreship to do it is cheaper for my case 😂
It is not hard. haha
It's 599.99 at the dealership
I followed your exact steps and got it all installed, have 70.00.100 installed (did that first) and it’s all up and running, but CarPlay isn’t working! Does anyone have any thoughts on this? I did a system reset to try to fix it but the CarPlay and android auto applications are completely greyed out and I can’t figure it out…
Sorry, I didn't have that issue. Maybe try to re-update after the install? I am just fishing.....
Will this work on a 2013 Mazda Axela BM (MAZDA 3 BM)
You check the link in the description to see if your car is supported.
did the back up camera still work?
yes
Will it work if my module is in the centre console?
Yes. Same unit.
I have mazda2 2019, Should I update the firmware first? Thanks
We did the software first.
@@GearGadgetExperiments Where can I find the software?I’m use in Hong Kong ，thanks for reply 🙇🏻♂️🙇🏻♂️🙏🏻
@@kaman60check the comments. One of the viewers found a how to video.
@@GearGadgetExperiments ok,thank you so much😎
No need for software update before installation?
Only need update if your current software is not the minimum stated on their Amazon product page
I found it with this video! Just did the upgrade in my 2015 Mazda 3, no issue. th-cam.com/video/dKS3WpcxIYo/w-d-xo.html
what version of firmware did you use? where did you download it from can you provide a link?
My son did the software upgrade. I will need to check with him.
Son said he can't remember where he found the file. Sorry.
I found it with this video! Just did the upgrade in my 2015 Mazda 3, no issue. th-cam.com/video/dKS3WpcxIYo/w-d-xo.html
I connected my connection likes yours and I can’t received the apple car play distraction message
In your Bluetooth device setting on your phone, is the "carplay" switch on?
I installed the adaptor on my mazda-3 2015 , its charging but the CarPlay is not working what could be the problem please ?
Did you ever figure it out, I have the same problem
Did you update your software?
Please help i have a MAZDA 3 with a dvd player, i took everything out and I dont even have the HUB unit for it please help urgently
Some Mazdas have the usb port in the armrest
@@GearGadgetExperiments ok i installed everything. My mazda says v56.0 but I need v70, how do I get to v70
@@PatrickZaksyou can look at the other comments. Someone gave a link to a video on how to do it.
Thanks for the video. How long did this take you?
With filming, about 1 hour. But take your time. Don't drop the bolt or scratch your dash.
Can this work for scion ia 2016?
The one in video is for Mazda. Maybe this one might work scion? maybe? amzn.to/3ZHpJRu
Would this work with 2015?
Check the link in the video description.
he said it wasn't too bad actually 😅
hardware hack seems way more stabel than the software one i treid wayback int he day was able to watch movies until it died tho
I have a 2018, I didnt take out the center console. I could get the top two legs with the long screw driver. For the lower legs, I went down where the pedals are, I removed the forward panel, then the lower air duct. From there I was prying with the screwdriver when the legs are and eventually I got it.
Awesome. You did what I was not able to do
You put up a hell of a fight!
@@GearGadgetExperiments I'm actually still doing it right now. I'm routing the cable on the left side instead of the right because of the blendoor/ac actuator. I think it's for the dual climate. I don't want the wires to ever get in the way.
Just finished!
🤙🏻
Hmmm, maybe I don’t need CarPlay
Where can I download the software?
My son said he doesn't remember where he found the file he used. Sorry
I found it with this video! Just did the upgrade in my 2015 Mazda 3, no issue. th-cam.com/video/dKS3WpcxIYo/w-d-xo.html
@@gamergodggpwnd Awesome! Thanks for the link. I will send people there also.
Couldn’t you just update the firmware to the latest and it add Apple CarPlay and Android auto? I think there’s a couple videos on TH-cam on how to do this. No need for installations
I want to see this video
Stupid ass Mazda makes it so difficult! Thank you for a great video though
it does seem harder than it should be. But, it is worth the effort to get CarPlay.
All that work? 😢 sigh just for an infotainment system.
leave the screen alone and drive. thats what your there for. distracted drivers are the number one cause for crashes today.
Is this work for 2015 Mazda 3 as well?
You can check the product link in the description for compatibility.