i was taught using a smaller pc first then each layer after that is slightly larger. this way each layer is bonded to the boat. by using a large pc first and its adhesion fails, then the entire patch falls off.
@@KnottsFishing backing with a pc of cardboard and wax paper over it would be my choice...i still like the fact of each layer coming in contact with the hull
@@KnottsFishing the paint sticks will hold up enough for you to get some glass down and won’t take up any space in that area. This also stoops it from sagging and preventing you to have to build multiple layers up
I know I know. Boats been sitting for about 2 years now. We moved houses had a baby and life has had me busy. Ill be getting back on the boat this fall/winter
There’s actually a good reason for this. Keeps the resin from sticking to areas not cleaned yet and the main reason is the dirt settles into the small spider cracks and shows up clear as day when your sanding the boat. Helps identify areas that you may not see if you pressure washed it all away.
Bro, the surface I worked and glassed on was ground down with a grinder sanded and wiped off with acetone and denatured alcohol. Pretty sure it’ll stick to where I want it to stick. Go back and reread why i left it dirty.
Finally a real world, no BS theory, minimum time and effort, great repair work. Thank you!
Thanks for the good words.
great stuff, mate! Just what I needed to get my boat fixed. Clear and straightforward repair. Keep up the good work.
Thank you!
Coming along nicely. Time to get that thing done, the season is here!!!
Dragging my feet, not looking forward to sanding all this non skid down....
Strip of marine ply; sub-grade lumber; or, teak placed in that channel/fiberglassed in place then topped with mesh & resin.
I like how you did the edge with that CSM, good idea!
Hey thanks Dave! The CSM Always feathers out really well. Thanks for watching!
So you did not put anykind of backing under the glass to screw in to ?
I dont plan on putting the rail back on.
hello, for under the water line holes that we dont have acces to both sides should we use mat or gloth
This is above water line repair.
Cool channel. Is there a reason you laid the 1708 mat side up? Thanks.
Thanks, Capt Mike! No reason, probably not paying attention.
What is that material you are covering? It looks like resin without the fiberglass.
1708 and resin.
@@KnottsFishing The red part that you were grinding at the beginning is 1708 fiberglass?
@@ecco222 oh yes I think thats why it cracked factory didnt have much glass in there at all seemed like it was almost all resin.
i was taught using a smaller pc first then each layer after that is slightly larger. this way each layer is bonded to the boat. by using a large pc first and its adhesion fails, then the entire patch falls off.
Ive heard of it both ways I used this method since I didnt use a backer to support the glass bigger piece so when it sagged it didnt fall through.
@@KnottsFishing backing with a pc of cardboard and wax paper over it would be my choice...i still like the fact of each layer coming in contact with the hull
@@johncartelli i agree 100, I was just being lazy and working quick.
Correct. Small to large.
WOW, this restoration is going great! I love the boat!
Thanks for watching! Ill keep the boat rebuild updated as I go.
I would clean it first the whole boat that way you see what needs to be fixed
It was cleaned then got dirty sitting in-between repairs with mildew.
There was so much Timelapse footage and music with that hole I almost fell in love with it
I almost loved it so much I ummm, nevermind. 😆
WTF... There is no glass in the affected area. I wonder how how far down the gunnel that problem runs?
Looks like fun in any case. Peace.
I was thinking the same thing looked like straight resin.
What kind of resins?
Im using polyester resin here.
Should have feathered the edges more before applying glass
Ill keep that in mind next time. Thank you.
How is every bodys resin looks that red and mine from west marine is kind of clear yellow haha
It’s a die you get in the hardener that allows you to know when the batch of resin is completely mixed.
Ive worked on some bad boats in my days at the boatyard, this one takes the crown..And you made it even worse with that horrible fiber job..Awefull
What would you have done differently?
Of course they gave no response.
Clean with acetone first always
Great advice.
Should have hot glued some paint stir sticks to plug the hole before you glass it up to prevent the glass from sagging
Yea I thought about that and for some reason thought it wouldnt sag that bad. I was wrong and had to build it up higher than needed.
@@KnottsFishing the paint sticks will hold up enough for you to get some glass down and won’t take up any space in that area. This also stoops it from sagging and preventing you to have to build multiple layers up
Im going to do that next time for sure! Thanks for the tip!
Whatever happened to the next video
I know I know. Boats been sitting for about 2 years now. We moved houses had a baby and life has had me busy. Ill be getting back on the boat this fall/winter
Yes, I’m eager to see a walkthrough when you are done!
@@rustymunroe1972 coming soon. Finishing one boat in the shop and itll he backing in to finally finish it.
Why not clean that damn thing before working on it! 😂
There’s actually a good reason for this. Keeps the resin from sticking to areas not cleaned yet and the main reason is the dirt settles into the small spider cracks and shows up clear as day when your sanding the boat. Helps identify areas that you may not see if you pressure washed it all away.
Dude resin will not adhere to a dirty surface. So there’s a very good reason for a clean work surface!
Bro, the surface I worked and glassed on was ground down with a grinder sanded and wiped off with acetone and denatured alcohol. Pretty sure it’ll stick to where I want it to stick. Go back and reread why i left it dirty.
@@terryfonz4603 same principle as a guide coat. Shows me the cracks when I’m sanding.
Is that epoxy resin? Just asking because I know epoxy resin gets a red tint when it ages
great job, you act like you have done that before...lol
Thank you! Done it a few more times than id like to admit.
Under fod the same masking tape better
Agreed, would have prevented sagging
Doveva fare l'inverso prima i fogli piccoli poi i grandi.
Alcuni dicono che inizia con il più piccolo e diventa più grande e altri dicono che inizia con il più grande e diventa più piccolo.
@@KnottsFishing scuole di pensiero, alla fine è il risultato. 😊😊
A Roma si chiamano pecioni😂😂
Si
You have no idea what you are doing. I hope nobody tries to follow your "system!!"
Right, seems to be working for me. 2 years old no issues so far. 😂😂
Please don't use the hand rail... It's for decoration
@@Prestigeandclassic im pretty sure i wont because I need the room for a trolling motor.
interessante
Thanks
Ne ho visto di tutorial ma stupido come questo nessuno!
Stupido è come stupido.