Best MK2 Aygo Bonnet/Hood Strut Upgrade?
ฝัง
- เผยแพร่เมื่อ 27 พ.ย. 2024
- 💥 Open your bonnet in seconds - amzn.to/3I6WIXe 💥
In this video, I install hood/bonnet struts onto the Aygo Mk2!
The links above may be affiliate links, so I may get a small commission if you buy something through them. Thanks for your fantastic support!
#toyotaaygo #hood #struts #installation #toyota #citybug #c1 #1080p
Disclaimer:
Due to factors beyond the control of Jamie Aygo, hereby referred to as Jamie Thorne, I cannot guarantee against improper use or unauthorized modifications of this information. Jamie Thorne assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Jamie Thorne recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Jamie Thorne, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Jamie Thorne.
Another great mod that I'll be keen to do! Already followed your head unit upgrade video, which was well worth it!
In Jamie Aygo we trust 😉
That's great to hear, Sam! I was skeptical at first with the upgrade, but it is such a great quality of life upgrade, isn't it. I'd happily recommend it to anyone looking to do it.
Another great mod and one I had not heard of! I will be doing this one too. I think you may have got the bonnet brackets the wrong side of the hinge? As you have sandwiched the new plate between the hinge and the bonnet, it will have the effect of raising the back of the bonnet slightly? Should the new plates be fitted under the hinge or won't they fit? I love my Aygo too!!!
That's a good observation re the hinges. From memory, it seems that you do put them in between the hinge and the bonnet based on the instructions, but you very well might be right! It will certainly raise the bonnet ever so slightly, but I didn't notice any particular issues with it. I think you could definitely fit them under the hinges, I just didn't. If you do give it a go, let me know how you get on and thank you for such a thoughtful comment!
Hi, I have finally fitted the kit myself (had a delay as dropped one of the slam panel balljoints never to be seen again, so had to order a replacement from China!!). Agree the instructions are confusing as they show it with the bonnet brackets both above and below the hinges. If above the hinges, then they raise the bonnet and the shut lines alter. However, I found out the bonnet bolts are stepped for location/alignment purposes and do not go through the slots in the bracket if the bracket is below the hinge. I decided to leave the bonnet bolts nearest the bulkhead in place to locate the bonnet, and cut the brackets down and filed the holes larger to enable the other stepped bolts to go through them. I then had to get thinner nuts for the ball studs that bolt to the hinge bracket. Anyway, all done and working well!! Thank you for bringing this mod to my attention. Cheers
Did the instructions state to actually put the bracket behind the hood hinge? That will destroy the alignment of the hood by lifting it up in the back like in the side shots of the car
No, the instructions where quite light on this detail, but you are right, it does lift it ever so slightly and it's something I need to change, which I will cover at some point.
Can you make a video for adding the front fog lights?
It's something I am certainly looking at! I'll do a little bit of digging to see how viable it is and if I find out it is, a video will absolutely be getting made!
Another great mod!! I love these model so much that I want Toyota to sell this small car model in my country instead of some Daihatsu rebrage as Toyota and call it Yaris 😢
Thank you! Yeah, it's a lovely little car with so much charm, isn't it.
Alright.. I know what my next upgrade is gonna be.
😂 Brilliant!
Use a magnet to find your clip.
Thanks for the suggestion. It's still out there somewhere!