F-150 Diode Dynamics LED Tail Light/Rear Turn Signal Red Pair 1997-16/Raptor 2010-14 Installation
ฝัง
- เผยแพร่เมื่อ 7 ก.ย. 2024
- Bill shows you how to install this Pair of Diode Dynamics Red LED Tail Light and Rear Turn Signal Bulbs on your 1997-2016 F-150 or 2010-2014 F-150 Raptor.
Purchase Product Here:
www.cjponyparts...
This Pair of Red LED Tail Light and Rear Turn Signal Bulbs is for 1997-2016 F-150s and 2010-2014 F-150 Raptors. Working for both your tail lights and rear turn signals, these bulbs make the perfect addition to the rear end of your F-150.
Being brighter, lasting longer and looking better are all advantages of picking up a set of LEDs for your F-150, so make sure to pick up some for your truck today! Sold as a pair; truck requires four total.
Check out more F-150 LED Lighting from CJ's here:
www.cjponyparts...
Check out more Diode Dynamics parts from CJ's here:
www.cjponypart...
Subscribe to CJ Off-Road on TH-cam here:
/ cjoffroad
Follow CJ Off-Road on Instagram here:
/ cjoffroad
Instale led normales sin resistencias, finalmente el hyperflash (de una ampolleta quemada) lo puedes eliminar mediante un escaner y forscan (software) , cambiando la configuración, lo hice y funcionó, me motivé a dejarlo así ya que las resistencias se calientan demasiado y derritieron cables.
10 min job compared to over a hour if you add the resistors. I let my shit hyper flash fuck it. Only hyper flashes when parking lights are on / head lights.
Thank you I went back to my original light I will look into that as soon as I get a chance
How about a before and after comparison? Old bulbs vs. LEDs.
great video...did this on my '14 and it worked great.
My left blinker an brake light don't get power.changed bulbs&fuses. What else can i do?
How about a bulb with a resistor built-in? Seems like a no-brainer.
Does it harm anything if you let it hyperflash?
Would have buy resisters for my tail lights and turn signal on my 2009 ford escape
My left tail light doesn't flash or light up for brake but running light work fine. This happen just on left tail light. I have removed all LED and return to factory. How can I find out what my issue is?
what is the point of the LED lights if you still use resistors? A Electronic LED Flasher Relay will be the way to go. Plus 10 to 20% more lumens output.
I installed 2 resistors per side and they are killing my battery now. My truck almost didn't start with a few mins of flashing. 100 watts per side drain and the resistors are very hot.
5:36 any corrosion protection needed or is this bed aluminum?
What was the resistor spec you used? 6 or 8 ohm?
Would re?sistors be needed at front flashers also for all around LED switch?
Do I need a resisitor if I'm replacing just the reverse lights to led lights?
I’m no expert but I changed my reverse lights to LED on my 12 f-150 and my 01 2500HD Silverado and haven’t had any issues with either bro. I noticed you didn’t get a response and since I did it I thought I would share my results with you.
Have you tried using dual colors led bulbs so that the turn signal would amber color?
Do you think the yellow light will be bright enough to shine yellow through the red housing?
Resistors also get very hot! its not good to run them. They get over 200 degrees in like 60 seconds.
Will a strobe brake light bulb work on the truck cause that’s what I want on mine
Get ready to do some soldering... The brackets break and the inline splicers suck....
So do u put 4 resistors in for each blub?
Do you have to put in a load resistor ?
So do I need a resistor per bulb?? There are 4 bulbs there
is it bad not to put the resister in it?. cause it kinda looks cool with it blinking faster.
It will probably wear out a little faster but I don't think it would hurt anything.
+Bill Tumas thanks!i mean just to save me some extra work i think ill do that. great video btw!
I said the same thing I like it blinking fast
It would affect the cruise control.
@@crlaw75 how ?
Does a plug a play resistor work, or do you need to use the ones that attached directly to the wires.
plug and play should work
last week I installed brake lights on my 2011 Ford F150 they work great but it makes my turn signal sound twice as loud and Fast I'll it do the same thing but this one?
If the bulbs you installed were LED they will cause the signal to blink faster. You can install load resistors to make them act normal again.
So can the resistors be mounted/drilled to either metal or plastic wall because my sport trac area I found to mount the resistor is plastic but wanna be sure if I can mount on the plastic wall piece of the vehicle and not gonna cause problem to wall piece when resistor gets hot?
Thanks!
Could you just change the flasher relay to a led flasher relay?
Yup, or you could install load resistors.
Or you could not cut into the harness and not cause extra problems by cutting wires. Don't be cheap, show install of a resistor for led lights. It is better for the truck, of course you won't because you get paid by manufacturers to put in cheap crap.
the relay for the turn signals on this f150 is not serviceable its a part of the bcm ...
I would have said it is the two outside wires on the plug to put the resistor on.
Do you need a resister
What size resistors did you use?
What did they need the drill for?
To mount the resistor to the metal, as if it touched the plastic or wires (since the resistor gets hot), it would melt either one of those.
Anyone else find themselves head banging watching this video.
Good👍
BAD Way to do it. Adding the resistor means it draws the same juice as the old bulb. Need to go back to the flasher electronics and fool it there with no extra amps required. Where is the flasher circuit? I also want more control on emergency flasher lights. To many rear enders
Too bad you couldn't do one resistor before it split off into two rear taillight bulbs instead of one resistor per bulb.
How come you did not just put the flasher relay in that would work with the led? Oh that's right you want them to buy your stuff and you make extra from adding resistors. If you are here looking at led's not that you can just change the flasher relay to one that will work with LED's.
that truck doesn't have a flasher relay, part of the BCM. Research before spewing nonsense.
what is the size socket they use
8mm to remove the tail light assembly.
I hope that in the near future they will ban red blinkers in Canada and USA! During bright sunny days you can't see them on most vehicles.
I agree! It's darn hazardous and dangerous! Most American cars are unmarketable overseas...
Please help
So all fine and great if you can get the lens off. That guy just pulls it off. Mine....I am 67 and not built like a gorilla and I can't come even close to getting that off. It's stupid to have to pay someone to just pull the lens.
dang lights would seem so easy to steal dont share this video id like to keep mine.
Keep your tailgate locked and it shouldn't be an issue.
I’m sorry but you lost me at using the Jesus clips... from a guy that has fixed way to much of other peoples stuff, throw those things in the garbage
I have 2012 Ford F-150 lariat no brake light and the right side is clicking faster I change the bulbs and change the turn signal switch I check the fuses and nothing please help
www.alibaba.com/product-detail/Clear-Smoke-Lens-High-Mount-LED_1600054777669.html?spm=a2747.manage.0.0.7f9471d2JrArB9
www.alibaba.com/product-detail/Clear-Lens-Bumper-Light-LED-Fog_1600059919888.html?spm=a2747.manage.0.0.7f9471d2JrArB9
www.alibaba.com/product-detail/Smoke-Lens-LED-Brake-Light-Tail_1600060986459.html?spm=a2747.manage.0.0.7f9471d2JrArB9
If you are interested, please contact us.